• Journal of the Korean Wood Science and Technology
• /
• 제10권3호
• /
• pp.152-164
• /
• 1982

1. In order to make the improvement of plywood quality, this study has been made. The pretreatments applied to the veneers are as follows. a) The soaking treatment of the veneer in 30 percent methanol solution for 24 hours was applied to remove some resinous materials which may cause many stain discolouring on the face of finished plywood. b) The preservative treatment of the veneer in 2 percent malenit solution for 2 to 3 minutes was adopted to make resistance against decay and insect damages. c) The fire retardant treatment of the veneer in 40 percent ammonium phosphate solution for 2 hours was applied to give retardation effect against fire burning. 2. The results summarized in this study are as follows. a) One percent resinous materials was extracted, after the soaking of the veneers in 30 percent diluted methanol. b) No marks of the dirty stains of resinous materials on the face of the treated plywood was shown, although many quite dirty stains on the face of untreated plywood have contrary seen. c) However, the strip shear test strength of the treated plywood was not decreased. It means that there is no difference in the strength between the treated plywood and the untreated plywood. The strength values were 25.08 kg/$cm^2$ and 24.98 kg/$cm^2$, respectively. d) The strip shear test strength of plywood made of the treated veneers in 2 percent malenit solution was not decreased. e) The slight decrease of the strip shear test strength of the treated plywood made of the treated veneer in 40 percent ammonuim phosphate solution was shown. However, the remarkable difference of the fire retardation activities between the treated specimens and the untreated specimens has seen as in Table 10, that is, the fire proofed specimens had taken about 28 seconds to start to burn, while the untreated specimens had taken 15 seconds to reach to burning. This means that the fire retardation effect of the fire proofed plywood was greater than that of the unproofed plywood.

• Journal of the Korean Wood Science and Technology
• /
• 제8권2호
• /
• pp.9-16
• /
• 1980

Papua New Guinea(PNG)산(産) TAUN재(材)를 이용한 합판제조 조건을 확립하였다. Taunwo(材)는 목질(木質)이 다양(多樣)하고 건조후 함수 분포가 균일(均一)치 못하여 퇴적(堆積)양생시키므로써 적정 함수분포를 유지할 수가 있었다. 또한 조직이 치밀하여 접착제와의 친화성이 낮아 집착불량이 용이하게 발생되기 쉬운 재(材)이나 제호시 수지율을 높여 도포하므로서 접착불량을 제거할 수가 있었다. Taun재(材)는 lauan재(材)나 kapur(材)와 혼합접합(混合接合) 하여도 접착력은 양호한 결과를 보였다.

• 한국해양공학회지
• /
• 제32권5호
• /
• pp.367-371
• /
• 2018

Plywood is one of the important materials in LNG cargo containment systems, and, due to the characteristics of the wood, its properties vary greatly depending on the humidity conditions in the storage facility. Due to the distribution environment of plywood, there is a high probability of long-term exposure to the domestic seasonal environment. Considering an environment in which the humidity changes greatly according to the seasons in Korea and the characteristics of the wood, it is necessary to acquire data on changes in the characteristics of the plywood for accurate quality control. In this study, the moisture content of plywood was determined experimentally to reflect the seasonal environmental conditions of shipyards in Korea. A noticeable change in the thermal conductivity was confirmed experimentally.

• Journal of the Korean Wood Science and Technology
• /
• 제40권4호
• /
• pp.287-293
• /
• 2012

본 연구에서는 현재 국내 목조건축에서 벽구성 재료로 많이 사용되고 있는 수입 OSB(배향성 스트랜드보드)를 국산 합판으로 대체하기 위해 OSB와 국산 합판의 못 접합부 전단성능을 비교 검토하였다. 주부재(잣나무)와 측면부재(OSB 합판)의 섬유 방향성(평행 직각)에 따른 전단성능은 합판에서 현저하였다. 결과, OSB와 합판 모두 현행 국내 기준인 못 접합부 기준 허용전단내력을 만족하는 것으로 나타났다. 그리고, 표면층에 MLH(열대산 활잡목)를 사용하고 7ply 구성한 합판(P-4 type)은 OSB보다 섬유방향에 관계없이 큰 전단성능을 나타냈다. 전반적으로 측면부재로서 합판을 사용할 경우 주부재에 대하여 섬유방향을 직교되도록 구성할 경우, 평행방향 구성보다 큰 전단성능을 발휘할 수 있음이 확인되었다.

• 한국가구학회지
• /
• 제23권3호
• /
• pp.298-304
• /
• 2012

Since 1990's, a flooring based on plywood has gotten customers' demand. Costs of raw material and production increased because of changed environment of industry. Tropical timber such as Red Meranti (Shorea acuminate) used for raw material of the floor has been depleting beside countries in South Eastern Asia changed species of afforestation. As a result, it gets hard to secure good quality of raw material for plywood. Moreover plywood price is increased suddenly after earthquake in Japan. Eucalyptus (Eucalyptus globulus) in china has been using for raw material as a countermeasure of changed environment of industry. In this study, possibility of using flooring consisted of Eucalyptus veneer as a core layer was checked by heat transfer experiments. Flooring consisted of Red Meranti was used for comparison. Two factors which impact on heat transfer are a type of density gradient and density difference between Long-grain veneer and Short-grain veneer. Red Meranti samples are 'M' type of density gradient on the other hand Eucalyptus samples are 'W' type of density gradient.

• Journal of the Korean Wood Science and Technology
• /
• 제26권1호
• /
• pp.87-96
• /
• 1998

The bending performances were evaluated at the radiata pine plywood through veneer compositions encompassing veneer quality, ply-numbers and overlays of the high density- or medium density-phenol resin impregnated sheets (hereafter abbreviated as resin sheets) on the raw plywood. In addition, a prediction on the bending MOE of veneers and plywoods was carried out by the nondestructive testing with stresswave timer. The summarized results were as follows: I. Bending strength and bending MOE of resin sheets-overlaid plywoods in parallel surface grain direction through 5 and 7ply were increased by 13 to 45% and 17 to 34%, respectively. Resin sheets-overlay occurred an increasing effect of the strength efficiency i.e. strength perpendicular-to-grain direction versus that parallel-to-grain direction, showing the phenomenon that the plywood strength becomes greater at the perpendicular-to-grain direction of 7ply than at that of 5ply. Displacement at bending failure had a greater trend at 7ply than at 5ply, and was decreased by resin sheets-overlay. 2. After the nondestructive bending MOEs were measured for individual veneers, these veneers were rearranged in plywood-manufacture. In these plywoods, including resin sheets-overlay, the actual MOE was predictable with feasibility of $R^2$=0.53, and also the nondestructively-evaluated MOE was lower by 20% in raw plywood, and higher 20% in LVL than actual bending MOEs.

• Journal of the Korean Wood Science and Technology
• /
• 제16권4호
• /
• pp.40-47
• /
• 1988

Our plywood manufacturing industries which entertained prosperous stage in late 1970's have come to be in face of the problems of conceedingly obtaining good quality logs and yield up-grading, which is considered by future-replaceable forest resources. In view of this point, manufacturing characteristic on softwood plywood using Japanese larch, pitch pine as domestic plantation species, and western hemlock as foreign species was studied. In this study, veneer- and plywood manufacturing yields were discussed in relation to log properties and veneer defects (knots). The summarized conclusions were as follows: 1. The majority of sample logs belonged to second grade on the standard. And, eccentricity of larch was the highest 11%, about 2 times those of pitch pine, hemlock. 2. Knot frequency of occurrence of larch reached 19% within log height 8m, and pitch pine 13% within 4m. Correspondingly, the log height of larch available for plywood manufacture was higher by about 2 times that of pitch pine. 3. In the knot types, most of knots of larch appeared dead, whereas those of pitch pine and hemlock appeared live. In size of knots, larch and hemlock showed relatively small 1-2cm dia. by 70% or more and pitch pine did the larger 24cm by 65%. Generally the more knot emerged in the inner side of veneer than the outer. 4. Plywood manufacturing yields by peeling with spindle revolution lathe were 37% in larch > 32% in hemlock> 26% in pitch pine. S. Jointed core veneer yields by peeling with outer perimeter back-up lathe were 55% in hemlock> 53% in larch> and 48% in pitch pine.

• Journal of the Korean Wood Science and Technology
• /
• 제33권5호통권133호
• /
• pp.50-56
• /
• 2005

The effect of wood material type on biocide retention and distribution during supercritical fluid impregnation was assessed using three different wood types including solid wood, plywood and oriented strand board (OSB). The result revealed that biocide treatability differed with structural composition and permeability of the various materials. Low treatability of plywood might be attributed to interferences of glue line limiting fluid movement. OSB samples showed higher biocide retentions, resulting from the presence of interconnecting gaps permitting more open flow.

• 한국가구학회지
• /
• 제13권2호
• /
• pp.29-38
• /
• 2002

Five type boxes, which are from brick, wood panel, charcoal-packed wood panel, plywood panel and charcoal-packed plywood panel, were prepared. Relationship of preservation characteristic of strawberry and change of relative humidity in the boxes were measured. Physical properties and industrial analysis of white charcoal used were also investigated. Physical Properties and industrial analysis showed that charcoal had: 1) $0.62-0.79g/cm^3$ of density, zero of refining degree and 8.6-9.4 of pH; and 2) 1.0-3.0% of moisture content, 1.9-2.9% of ash content, 3.9-5.0 of volatiles and 89.2-93.2% of fixed carbon, indicating high quality. During the experimental period, relative humidity was highest in the brick box and lowest in the charcoal-packed plywood panel box. Weight loss of strawberry was greatest in charcoal-packed wood Panel box and very little in brick box. In the boxes with charcoal, strawberry was preserved for 6 days without mold, but in brick box it was covered with mold in 3 days. From these results, it is suggested that charcoal-packed wood panel can be used for better ecomaterial.

• Journal of the Korean Wood Science and Technology
• /
• 제39권5호
• /
• pp.451-458
• /
• 2011

Adhesives derived from renewable resources allow wood panel producers to make lower cost alternatives to formaldehyde-based adhesive resins. Among them, adhesive components extracted from industrial by-products or wastes are the most important research fields in the efficient utilization of waste and cost reduction. In our study, the rapeseed flour, which is a by product from the production of biodiesel extracted from rapeseed, was introduced to develop alternative adhesives for the production of wood flooring. The rapeseed flour was hydrolyzed with 1% sodium hydroxide solution and PF prepolymers were prepared with 3-molar ratios, 1.8, 2.1 and 2.4. The linear fracture mechanics was introduced to evaluate the glue bond quality in wood flooring composed of fancy-veneered and plywood, and the formaldehyde emission and adhesive penetration were also investigated. The formaldehyde emissions of wood flooring met the requirement of the standard of $SE_0$ specified in the KS standard. The rapeseed flour adhesive penetrated sufficiently into the vessel elements and lumens in fancy veneer and plywood and gave strong bond quality to the wood flooring. The fracture mechanics was introduced to evaluate the adhesive joint between fancy veneer and plywood. The critical stress intensity factor ($K_{IC}$) of boliva overlayed wood flooring was increased with increasing molar ratio and this was the same tendency in oak overlayed wood flooring. From the results, the formulated adhesives were efficiently used to bond fancy veneer onto the plywood to make wood flooring and showed a potential to be used as a component of environmentally friendly adhesive resin systems for production of flooring.