• Journal of the Earthquake Engineering Society of Korea
• /
• v.2 no.4
• /
• pp.23-30
• /
• 1998

During an earthquake, there are three components of excitation : horizontal excitation of the ground, vertical excitation of the pile due to superstructure feedback produced by vertical excitation of the ground, and the seawater excitation by the vertical ground shaking, that is, "the seaquake." These excitations could have effects on the pore pressure buildup mode induced in the near-field of open-ended pile and the soil plugs in open-ended pipe piles installed at offshore sites. While the ground and pile excitation could be modeled by exciting the soil and pile with simulated motions, seaquake excitation induced by the vertical ground shaking can be modeled by pulsing the water pressure at the seabed. The objectives of this study were to observe buildup trend for the porewater pressures developed in near-field of open-ended pipe pile installed in the calibration chamber during the simulated earthquake and seaquake and, also to confirm the cause for reduction of soil plugging according to pore pressure buildup. During the simulated horizontal seismic motion, there was no upward flow through soil plug because the similar magnitude of excess porewater pressure were occurred at the top and under the toe of soil plug. During the horizontal seismic motion, relatively higher hydraulic gradients caused upward flow in the soil plug and then the degradation of plugging resistance was about 20%. During seaquake, in the case of the open-ended pile installed in a deep sea with more than 220m of water depth, soil plug failed completely because of high upward hydraulic gradients through soil plug.soil plug.

• Current Research on Agriculture and Life Sciences
• /
• v.6
• /
• pp.19-24
• /
• 1988

The present experiment was undertaken to study the influence of light intensity on plug establishment of zoysia-82, chewings fescue and red fescue. The results obtained are summarized as follows : In chewings fescue and zoysia-82, plant height and leaf length were increased and leaf width was decreased by reducing light intensity. But in red fescue, plant height and leaf length measured at 90 and 120 days after plugging under 9% of incident light were shorter than those under 30% of incident light. Percent ground cover was decreased by reducing light intensity in chewings fescue, red fescue and zoysia-82. Each part of dry weight in three species was getting lighter by reducing light intensity. Decrease of light intensity in zoysia-82 causes increasing chlorophyll a, b, and total chlorophyll content. But red fescue and chewings fescue had the most plentiful chlorophyll under 30% of incident light. Chewings fescue and red fescue had the lowest concentration of chlorophyll a/b under natural light intensity. But zoysia-82 had the lowest concentration of chlorophyll a/b under 30% of incident light. Tillering number of chewings fescue and red fescue was decreased by reducing light intensity. Internode length of zoysia-82 was longer in the order of : 1) 30% of incident light, 2) natural light, 3) 9% of incident light. And internode diameter was decreased by reducing light intensity.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.1
• /
• pp.185-194
• /
• 2012

Deepwater oil is becoming more attractive because most onshore and shallow water oil is developing or developed. With the on-going trend to deepwater oil developments, flow assurance problems which prevent oil flow from reservoir to processing facilities are becoming an issue because deposited material can be occurred in case oil is exposed to very different environment from reservoir. Wax deposition which is one of flow assurance problems can be a major technical and economic issue because it is very sensitive to temperature. In order to predict and mitigate wax problems, the precise measurement of wax appearance temperature (WAT) which is the starting temperature of wax precipitation is very important. Various methods have been suggested for WAT measurement of opaque oil because there is no standard method for opaque oil. In this study, the WAT of opaque oil samples was measured using viscosity measurement method, differential scanning calorimetry, filter plugging method, and pressurized filter plugging method. Wax deposition test and high temperature gas chromatography analysis were applied to verify measured WAT. As a result of study, the WAT of opaque oils was successfully measured and verified. If WAT measurement methods of opaque oil related to oil characteristics is systematized using the results of this study, it can be a valuable tool for WAT measurement of opaque oil and flow assurance related to wax deposition.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.1
• /
• pp.113-119
• /
• 2014

The compositions of saturated and unsaturated fatty acids in biodiesel feedstocks are important factors for biodiesel properties including low-temperature fluidity and oxidative stability. This study was conducted to improve low-temperature fluidity of biodiesel by reducing total saturated FAME (fatty acid methyl ester) in animal fat biodiesel fuels via urea-based fractionation and by mixing plant biodiesel fuels (rapeseed-FAME, waste cooking oil-FAME, soybean-FAME, and camellia-FAME) with enriched-polyunsaturated FAME derived from animal fat biodiesel. Our results showed that the reduction of total saturated FAME in animal fat biodiesel lowered CFPP (Cold Filter Plugging Point) to $-15^{\circ}C$. Mixing plant biodiesel fuels with the enriched-polyunsaturated FAME derived from animal fat biodiesel lowered CFPP of blended biodiesel fuels to $-10{\sim}-18^{\circ}C$.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.24 no.2
• /
• pp.153-170
• /
• 2022

Waterjet has been comprehensively used in urban areas owing to a suitable technique for cutting concrete and rock, and low noise and vibration. Recently, the abrasive waterjet technique has been adopted and applied by the Korea Atomic Energy Research Institute to demolish concrete plugging without disturbing and damaging In-situ Demonstration of Engineered Barrier System in the disposal research tunnel. In this study, the use of abrasive waterjet in the tunnel was evaluated for practical applicability and the existing cutting model was compared with the experimental results. As a variable for waterjet cutting, multi-cutting, water flow rate, abrasive flow rate, and standoff distance were selected for the diversity of analysis. As regarding the practical application, the waterjet facilitated path selection for cutting the concrete plugging and prevented additional disturbances in the periphery. The pump's noise at idling was 64.9 dB which is satisfied with the noise regulatory standard, but it exceeded the standard at ejection to air and target concrete because the experiment was performed in the tunnel space. The experimental result showed that the error between the predicted and measured cutting volume was 12~13% for the first cut and 16% for second cut. The standoff distance had a significant influence on the cutting depth and width, and the error tended to decrease with decrement of standoff distance.

• Journal of the Korean GEO-environmental Society
• /
• v.23 no.12
• /
• pp.5-15
• /
• 2022

Conventionally, because evaluation methods of the bearing capacity for double steel pipe-concrete composite pile design have not been established, the conventional vertical bearing capacity equations for steel hollow pile are used. However, there are severe differences between the predictions from these equations, and the most conservative one among vertical bearing capacity predictions are conventionally adopted as a design value. Consequently, the current prediction method for vertical bearing capacity of composite pile prediction composite pile causes design reliability and economical feasibility to be low. This paper investigated mechanical behaviors of a new composite pile, with a cross-section composed of double steel pipes filled with concrete (DSCT), vertical bearing capacities were analyzed for several DSCT pile conditions. Axisymmetric finite element models for DSCT pile and surrounding ground were created and they were used to analyze effects on behaviors of DSCT pile pile by embedding depth, stiffness of plugging material at pile tip, height of plugging material at pile tip, and rockbed material. Additionally, results from conventional design prediction equations for vertical bearing capacity at steel hollow pile tip were compared with that from numerical results, and the use of the conventional equations for steel hollow pile was examined to apply to that for DSCT pile.

• Clean Technology
• /
• v.29 no.1
• /
• pp.71-75
• /
• 2023

In general, the presence of non-selective intercrystalline (grain boundary) defects in polycrystalline metal-organic framework (MOF) or zeolite membranes, which are known to be ca. 1 nm in size, causes lower membrane performance (selectivity) than the intrinsically expected. In this study we show that applying a thin polymeric coating of polydimethylsiloxane (PDMS) on a polycrystalline MOF membrane is effective to cap the non-selective intercrystalline defects and therefore improve membrane performance. To demonstrate the concept, first, polycrystalline UiO-66, one of Zr-based MOFs, membranes were prepared by an in-situ solvothermal growth. By controlling membrane growth condition with respect to growth temperature, we were able to obtain polycrystalline UiO-66 membranes at 150 ℃ with intercrystalline defects of which the quantity is not significant, so it can be plugged by the suggested PDMS deposition. Second, their performances were compared before and after the PDMS deposition. As expected, the PDMS deposition ended up with a noticeable increase in CO₂/N₂ ideal selectivity from 6 to 14, indicating successful intercrystalline defect plugging. However, the enhancement in CO₂/N₂ selectivity was accompanied by a significant reduction in CO₂ permeance from 5700 to 33 GPU because the PDMS deposition not only plugs defects but also forms a continuous coating on membrane surface, adding an additional transport resistance.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.17 no.1
• /
• pp.39-48
• /
• 2009

Biodiesel is estimated to be the best recycling energy source as an alternative fuel for transportation vehicles which represents the biggest share of greenhouse effect gas exhausts. Thus, in order to widely expand use of biodiesel and to enhancement its reliability, studies on quality improvement of biodiesel is needed. In this study, we have produced biodiesel(BD100, BD20) through esterification reaction using raw material of waste frying oil and analyzed compatibility with 24 items of quality criteria. As waste frying oil has high contents of unsaturated fatty acid such as Oleic acid, Linoleic acid and Linolenic acid, it is confirmed that there is no problem in using the same as a raw material of biodiesel. The result of analyzing the quality criteria items of biodiesel showed that it satisfied all the quality criteria except the oxidation stability of BD100, which was 2 hours, fatty acid methyl ester of BD20, which was 18.6w% and the filter plugging point, which was $-5^{\circ}C$. We believe that it will contribute to improved utilization of waste resources as alternative energy if studies on technology to improve quality of some items are provided.

• Korean Journal of Radiology
• /
• v.25 no.7
• /
• pp.673-683
• /
• 2024

Objective: To evaluate the role of visual and quantitative chest CT parameters in assessing treatment response in patients with severe asthma. Materials and Methods: Korean participants enrolled in a prospective multicenter study, named the Precision Medicine Intervention in Severe Asthma study, from May 2020 to August 2021, underwent baseline and follow-up chest CT scans (inspiration/expiration) 10-12 months apart, before and after biologic treatment. Two radiologists scored bronchiectasis severity and mucus plugging extent. Quantitative parameters were obtained from each CT scan as follows: normal lung area (normal), air trapping without emphysema (AT without emph), air trapping with emphysema (AT with emph), and airway (total branch count, Pi10). Clinical parameters, including pulmonary function tests (forced expiratory volume in 1 s [FEV1] and FEV1/forced vital capacity [FVC]), sputum and blood eosinophil count, were assessed at initial and follow-up stages. Changes in CT parameters were correlated with changes in clinical parameters using Pearson or Spearman correlation. Results: Thirty-four participants (female:male, 20:14; median age, 50.5 years) diagnosed with severe asthma from three centers were included. Changes in the bronchiectasis and mucus plugging extent scores were negatively correlated with changes in FEV1 and FEV1/FVC (ρ = from -0.544 to -0.368, all P < 0.05). Changes in quantitative CT parameters were correlated with changes in FEV1 (normal, r = 0.373 [P = 0.030], AT without emph, r = -0.351 [P = 0.042]), FEV1/FVC (normal, r = 0.390 [P = 0.022], AT without emph, r = -0.370 [P = 0.031]). Changes in total branch count were positively correlated with changes in FEV1 (r = 0.349 [P = 0.043]). There was no correlation between changes in Pi10 and the clinical parameters (P > 0.05). Conclusion: Visual and quantitative CT parameters of normal, AT without emph, and total branch count may be effective for evaluating treatment response in patients with severe asthma.

• Journal of Computing Science and Engineering
• /
• v.2 no.1
• /
• pp.1-25
• /
• 2008

Spoken dialog tasks incur many errors including speech recognition errors, understanding errors, and even dialog management errors. These errors create a big gap between the user's intention and the system's understanding, which eventually results in a misinterpretation. To fill in the gap, people in human-to-human dialogs try to clarify the major causes of the misunderstanding to selectively correct them. This paper presents a method of clarification techniques to human-to-machine spoken dialog systems. We viewed the clarification dialog as a two-step problem-Belief confirmation and Clarification strategy establishment. To confirm the belief, we organized the clarification process into three systematic phases. In the belief confirmation phase, we consider the overall dialog system's processes including speech recognition, language understanding and semantic slot and value pairs for clarification dialog management. A clarification expert is developed for establishing clarification dialog strategy. In addition, we proposed a new design of plugging clarification dialog module in a given expert based dialog system. The experiment results demonstrate that the error verifiers effectively catch the word and utterance-level semantic errors and the clarification experts actually increase the dialog success rate and the dialog efficiency.