• Journal of the Korean Ceramic Society
• /
• v.39 no.12
• /
• pp.1143-1148
• /
• 2002

Precipitated calcium carbonate is one of the most versatile mineral fillers and is consumed in an wide range of products including paper, paint, plastics, rubber, textiles, sealants, adhesives and printing ink and can be produced by several methods. Calcium carbonate has three isomorphism; vaterite, aragonite and calcite, with numerous variations of morphology in the natural mineral or organism. Formation process of vaterite in the reaction of system $Ca(OH)_2-CH_3OH-H_2O-CO_2$ were investigated by measuring the electrical conductivity, $Ca^{2+}$ ion concentration, pH in the slurries and by means of X-ray diffraction and electron microscopic observation. It was clearly established that the reaction temperature is important variable in the carbonation process; in general over 50${\circ}C$, the vaterite was precipitated with the calcite and aragonite. SEM and XRD observations revealed that the vaterite formation could be prepared the temperature range of 40 to 50${\circ}C$ and mean size of particles in this range is controlled from 0.5 to 0.8 ${\mu}m$.

• Journal of Adhesion and Interface
• /
• v.16 no.1
• /
• pp.29-34
• /
• 2015

Hydrocarbon resins, which are defined as low molecular weight, amorphous, and thermoplastic polymers, are widely used as tackifier for various types of adhesives, as processing aids in rubber compounds, and as modifiers for plastics polymers such as isotactic polypropylene. Typically, hydrocarbon resins are non-polar, and thus highly compatible with non-polar rubbers and polymer. However, they are poorly compatible with polar system, such as acrylic copolymer, polyurethanes, and polyamides. Moreover, recently the raw materials of hydrocarbon resin from naphtha cracking had been decreased because of light feed cracking such as gas cracking. To overcome this problem, in this study, novel hydrocarbon resins were designed to have a highly polar chemical structure which material is sustainable. And, it was successfully synthesized by Diels-Alder reaction of dicyclopentadiene monomer and sorbic acid from blueberry as renewable resources. Acrylic resins were formulated with various tackifiers solution including sorbic acid grafted hydrogenated dicyclopentadiene hydrocarbon resins in acrylic adhesive and rolling ball tack, loop tack, $180^{\circ}$ peel adhesion strength, and shear adhesion strength were measured. The properties depend on the softening point and polar content of tackifiers.

• Clean Technology
• /
• v.19 no.4
• /
• pp.401-409
• /
• 2013

BBiodegradable polymers have attracted great attention because of the increased environmental pollution by waste plastics. In this study, PLA (polylactic acid)/Clay-20 (Cloisite 20) and PLA (polylactic acid)/PBS (poly(butylene succinate)/Clay-20 (Cloisite 20) nanocomposites were manufactured in a twin-screw extruder. Specimens for mechanical properties of PLA/Clay-20 and PLA/PBS (90/10)/Clay-20 nanocomposites were prepared by injection molding. Thermal, mechanical, morphological and raman spectral properties of two nanocomposites were investigated by differential scanning calorimetry (DSC), tensile tester, scanning electron microscopy (SEM) and raman-microscope spectrophotometer, respectively. In addition, hydrolytic degradation properties of two nanocomposites were investigated by hydrolytic degradation test. It was confirmed that the crystallinity of PLA/Clay-20 and PLA/PBS/Clay-20 nanocomposite was increased with increasing Clay-20 content and the Clay-20 is miscible with PLA and PLA/PBS resin from DSC and SEM results. Tensile strength of two nanocomposites was decreased, but thier elongation, impact strength, tensile modulus and flexural modulus were increased with an increase of Clay-20 content. The impact strength of PLA/Clay-20 and PLA/PBS/Clay-20 nanocomposites with 5 wt% of Clay-20 content was increased above twice than that of pure PLA and PLA/PBS (90/10). The hydrolytic degradation rate of PLA/Clay-20 nanocomposite with 3 wt% of Clay-20 content was accelerated about twice than that of pure PLA. The reason is that degradation may occur in the PLA and Clay-20 interface easily because of hydrophilic property of organic Clay-20. It was confirmed that a proper amount of Clay-20 can improve the mechanical properties of PLA and can control biodegradable property of PLA.

• Polymer(Korea)
• /
• v.27 no.6
• /
• pp.562-568
• /
• 2003

Environmental problems due to waste tire and waste plastics let us develop practical and economically feasible products. For this purpose, the characteristics of waste tire/plastic composites including various additives were examined using internal mixer. Experimental results indicated that the tensile strength and the flexural strength of waste tire/plastic composites decreased with the waste tire content. When 20 wt% of PP was added to the waste tire (60 wt%)/HDPE composites, the tensile strength was 1.5 times higher than the composite without PP, It was also found that the strain at break of composites increased by 2.5 times with 10 wt% addition of ethylene vinyl acetate and styrene ethylene butylenes styrene respectively. When 10 wt% of glass fiber was added to waste tire (60 wt%)/ HDPE composites, the tensile strength was 63% higher than the composite without glass fiber.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.4
• /
• pp.364-371
• /
• 2009

This study was carried out to investigate the bending strength of the Larix glulam beams which were reinforced with CFRP (Carbon fiber reinforced plastic) of which the reinforcement ratios were 0.7% and 2.1% by volume. In the bending test, the rupture shape of the reinforced glulam shows that the reinforced glulam broke firstly in the lowest bottom layer on which tension was loaded, but did not in the upper part reinforced with the CFRP layer. The upper part of the reinforced layer kept strength and did not break when the reinforced glulam broke firstly at the bottom part of the reinforced layer, but broke secondly as loading was increased. In the glulam beams reinforced with CFRP of which the reinforcement ratio was 0.7% by volume, the bending strength of the reinforced beams was increased by 28% at the first break. When beams broke up to the upper part of the reinforced layer, the bending strength of the reinforced beams was increased by 55%, compared to those of control glulam beams. When the glulam beams were reinforced with CFRP of which the reinforcement ratio was 2.1% by volume, the bending strength of the reinforced beams was increased by 77%, compared to those of control glulam beams. The ratio of the height of calculated neutral axis using failure mode recommended by Romani and the height of actual neutral axis using strain gauge was 1.03 and agreed well.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.4
• /
• pp.357-363
• /
• 2009

This study was carried out to investigate whether adhesive used in manufacturing glulam can be used to bond wood and GFRP, when considering working process and economical efficiency. The six different glulams were manufactured, changing the adhesives and the mixing ratios of the adhesives, and investigated by the block shear test and the delamination of the water soaking or boiling water soaking. The three glulams were manufactured, using the resocinol resin based adhesive, the PVAc resin based adhesive and the epoxy resin adhesive, and the other three glulams, using the adhesives mixing resocinol resin and PVAc resin. The block shear strength is higher than $7.1N/mm^2$ in all types, which is standard of KS F3021. However, in the wood failure the block shear strength was the highest as 65.9% in the PVAc. The delamination of glulams glued with PVAc adhesive, which was 1.08% in water soaking and 4.16% in boiling water soaking, was lower than 5.00% which is the standard of KS F 3021, and the adhesive strength is good. In glulams glued with only resocinol resin adhesive, the wood layers were good as 1.26% in the water soaking delamination and 0.00% in the boiling water soaking delamination. The GFRP layers were not good as 21.85% in the water soaking delamination but were good as 1.45% in the boiling water soaking delamination.

• Fire Science and Engineering
• /
• v.25 no.6
• /
• pp.168-177
• /
• 2011

The combustion test for real box of AC outdoor unit has been performed in this study in order to estimate the fire hazard in multi-system type of AC outdoor unit which is currently used for commercial use. The result showed that in test, there was explosion inside of AC outdoor unit, and flame erupted and fire spread through upper side grill. And then this fire burnt the combustibles such as wires, electronic control board, heat exchange copper plate and plastics etc inside the unit, refrigerant gas pipe was burst due to fire, and accelerated the explosion and flame eruption to outside while the refrigerant was erupting. It is found in this test that the maximum heat release rate of AC outdoor unit is 5,830 kW, the maximum internal temperature measured with infrared camera and thermocouple is $1,201^{\circ}C$, maximum ambient temperature is $881^{\circ}C$, and flame rose higher than about 5 m. It is concluded that the fire in AC outdoor unit cause fire to combustibles around the unit, and may give big damage by generating the secondary fire. It is expected that the result obtained from the test on the real object may be applied to fire realization of AC outdoor unit and estimation of fire spreading to the combustibles around in the future computer simulation.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.5
• /
• pp.494-500
• /
• 2006

Life Cycle Assessment(LCA) is an environmental assessment tool for evaluating environmental burdens associated with products, processes and activities from the raw material acquisition stage to the end-of-life stage. End-of-life stage as well as other processes requires a reliant database in order to increase the confidence in the LCA results. In this study, the flow of Personal Computer(as PC) in the end-of-life stage was examined and the database of two scenarios has been established, i.e. one is part reuse and the other is no part reuse, in the end-of-life phase of PC. Also, key environmental issues were identified by carrying out LCA on a PC in the end-of-life phase for eight environmental impact categories. The 'ozone layer depletion' contributes the highest environmental impact due to generation of $Cl_2$ gas during the incineration of waste plastics. In addition, the scenario 1(part reuse) is more environmentally sound than the scenario 2(no part reuse) when comparing two scenarios.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.3
• /
• pp.382-388
• /
• 2007

Statement of problem. The role of calcium sulfate in stimulating the growth of gingival soft tissue has been reported in few studies. Such a unique property of calcium sulfate could serve as a trouble-solving broker in compensating for the lack of soft tissues in various oral surgeries. Purpose. The purpose of this study was to compare the proliferating activities of human gingival fibroblasts seeded on various bone graft barrier materials of calcium sulfate, collagen, and polytetrafluorethylene (PTFE). Material and methods. Two calcium sulfates ($CAPSET^{(R)}$. and $CalForma^{(R)}$, Lifecore Biomedical Inc., St. Paul, Minnesota, USA), a resorbable natural collagen ($Bio-Gide^{(R)}$, Geistlich Pharma Ag., Wolhusen, Switzerland), and a non-resorbable PTFE ($TefGen-FD^{(R)}$, Lifecore Biomedical Inc., St. Paul, Minnesota, USA) served as the human gingival fibroblasts' substrates and comprised the four experimental groups, whereas the untreated floors of culture plastics were used in the control group, in this study. Cells were trypsinized, seeded, and incubated for 48 h. The proliferating activities of fibroblasts were determined by XTT and SRB assay and absorbance (optical density, OD) was measured. One-way ANOVA was used to analyze the differences in the mean OD values between the groups of CAPSET, CalForma, Bio-Gide, TefGen, and the control (p<0.05). Results. From the XTT assay, the mean OD value of the control group, the highest, was significantly greater than that of any of the four experimental groups followed by CalForma, CAPSET, TefGen, and Bio-Gide. Further, the mean OD value of CalForma, was significantly greater compared to that of Bio-Gide. From the SRB assay, Calforma showed the highest mean OD value, which was significantly greater than that of any other groups, followed by the control, CAPSET, Bio-Gide, and TefGen. The mean OD values of both the control and CAPSET were significantly greater compared to that of TefGen (p<0.05). Conclusion. Assessment of the viability and proliferation of cultured fibroblasts seeded and incubated for 48 h on various barrier-material substrates using XTT and SRB assay showed that calcium sulfate $CalForma^{(R)}$ promotes the proliferating activity of human gingival fibroblasts.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.35 no.5
• /
• pp.64-72
• /
• 2007

This study investigated the types, forms, and origination of litter found along one hiking course in Moaksan Provincial Park, 'Jungin-ri Course'(entrance-ridge-valley-peak). In addition, a survey was conducted to understand hikers' litter control awareness in order to determine possible backcountry litter control measures. The following are the results of this study: 1. For the litter Sequency investigation, 199 recyclable pieces of litter were found on the mid-slope(61.6%), 89 by the entrance(27.6%), 19 in the valley(5.9%) and 16 on the peak(4.9%). A total of 323 pieces of litter were found. Paper materials were the most common, followed by plastic containers such as PET bottles and yogurt containers. Of particular interest, 288 papers and cans were found on the mid-slope(46.9%). By the entrance, more plastics and bottles were found. 2. There were 614 pieces of flammable litter collected and only 19 pieces of non-flammable. Most of the flammable litter, including snack pacts, plastic bags, processed lumber, cigarette butts, tissues, cigarette boxes, and fabric was found on the mid-slope. 3. Very little food waste was found throughout the whole site proving that the policy prohibiting hikers from cooking and eating at the designated sites has been effective. However, food waste is difficult to find because it naturally decays with time. 4. $X^2$-test was used to find different types of litter and their verified origination frequency. It was found that recyclable litter, and food waste took about 1%. In addition, recyclable litter, especially bottles, was found relatively frequently by the entrance. Flammable litter was found most often at the peak. 5. The questionnaire results showed that 48.2% of the respondents "shorten their hiking journey and purchase food outside the entrance" and 29.6% said that they "bring a packed meal from home". Only 8.2% said that they "cook something when an appropriate location is found". At the Jungin-ri course, a few hikers brought their own food to eat or cook, but most hikers purchased something to eat onsite. 6. The results of the question about having experience littering while hiking showed that 19.3% litter and 79.2% do not. Those that responded "yes" gave various reasons for littering. 63.6% claimed, "there are no designated trash containers". 15.9% said they litter subconsciously. Finally, 3.2% insist that they litter "because food naturally decomposes". 7. As a result of the overall satisfaction according to the Likert scale and the analysis with an average of 14 variables, it was found that the average "toxic litter control convenience" was 2.41 with very low satisfaction. Thus, the results indicate the importance of providing appropriate back country litter control facilities.