본 연구에서는 반강접 접합부 배치에 따른 구조물 거동특성을 파악하기 위하여 KBC2005 건축구조설계기준으로 비가새 5층 철골 구조물을 설계하여 모든 접합부를 완전 강접합부와 반강접 접합부로 이상화한 경우 그리고 반강접 접합부를 수직배치 및 수평배치한 경우에 대하여 비탄성 시간이력 구조해석을 실시하였다. 철골 보 및 기둥의 모멘트-곡률 관계는 화이버모델을 이용하여 확인하였으며 반강접 접합부의 모멘트-회전각 관계는 3-매개변수 파워모델 그리고 철골 보, 기둥 및 접합부의 이력거동은 3-매개변수 모델을 이용하여 나타내었다. 4개 지진파에 대한 재현주기 2400년 위험수준에 해당하는 최대지반가속도와 5% 층간변위에 대한 푸쉬오버 구조해석의 최대밑면전단력 발생 최대지반가속도에 대하여 시간이력 구조해석을 실시하여 밑면전단력, 지붕층 변위, 층간변위, 접합부 요구연성도, 기둥, 보 및 접합부의 최대휨모멘트 그리고 소성힌지 분포 등을 확인하였다. 반강접 접합부를 수직적으로 외부에 배치할수록 최대밑면전단력과 층간변위는 감소하며, 수평적으로 상부층에 배치할수록 접합부 요구연성도가 감소하였다. 푸쉬오버 구조해석과 시간이력 구조해석에서 최대층간변위 발생 위치가 다르고 크기는 푸쉬오버 구조해석에서 과대평가되었다. 밑면전단력, 층간변위 및 접합부 요구연성도를 위한 가장 바람직한 반강접 접합부 배치는 수직적으로 외부에 배치하는 것이다.
본 연구에서는 횡력을 받는 구조물 거동에 대한 보-기둥 접합부의 영향을 확인하기 위하여 5층 철골구조물을 KBC2005 건축구조 설계기준에 맞게 구조설계 하였으며 접합부를 완전 강접합부로 이상화한 경우와 반강접 접합부로 설계하였다. 철골 보 및 기둥의 모멘트-곡률관계는 화이버모델을 이용하여 확인하였으며 반강접 접합부의 모멘트-회전각 관계는 파워모델 그리고 철골 보, 기둥 및 접합부의 이력거동은 3-매개변수 모델을 이용하여 나타내었다. 5층 철골구조물은 개별골조와 연결골조의 2차원 구조물로 이상화하였다. 4개 지진파의 재현주기 수준별로 산정한 최대지반가속도와 푸쉬오버해석의 최대밑면전단력을 위한 지반가속도에 대하여 시간이력해석을 실시하여 지붕층 변위, 밑면전단력, 층간변위, 접합부 요구연성도, 기둥, 보 및 접합부의 최대모멘트 그리고 소성힌지 분포 등을 확인하였다. 반강접 접합부 골조는 완전 강접합 골조에 비해 적은 밑면전단력이 발생하였으며 기둥, 보 및 접합부에 발생하는 휨모멘트의 크기와 증가율도 적었다. TSD 접합부는 우리나라 설계수준의 지진하중에 대하여 예제 구조물에서 경제성과 안전성을 확보 할 수 있음을 확인할 수 있었다.
본원에서 하악지시상골 절단술을 시행한 하악전돌증 환자 29명 (남자 12명, 여자 17명)을 대상으로 수술전, 수술후, 장기관찰기간동안 경조직과 연조직 변화를 관찰한 결과 다음과 같은 결과를 얻었다. 1. 술후 하악은 반시계방향회전하면서 후방이동 하였으며 장기관찰시 B와 Pog에서 1.23mm, 1.28mm의 재발을 보였다. 이는 술후의 하악이동에 따른 순수한 효과(Net effect)가 81.7%, 82.2% 라는 것을 의미하며 이러한 재발로 인하여 수술의 효과를 감소시킬 수 있다는 사실을 술전 치료계획에 포함시켜야 한다고 할 수 있다. 2. 하악 경조직의 수평변화에 대한 하악 연조직의 변화비율은 하순구에서 100%, 이부에서 99.1-102.1% 로 나타났으며 하순의 경우 72.7-93.7% 로 나타났으며 상순의 경우 하악 전치 이동량의 5.7% 정도 후방 이동하게 되지만 통계적 상관관계는 미약했으나. 수직적으로 8.3-9.6% 정도 유의한 하방이동양상을 보였다. 3. 술수 상순과 하순의 관계가 개선되어 심미선에 대하여 상순(Ls)은 상대적으로 동출하고 하순(Li)은 후방이동하였으며, 상순구가 얕아지고 하순구가 깊어졌으며, 비순각이 개선되어 전반적 안모가 개선되었으나 턱부위의 전돌은 수술후에도 약간 남아있었다. 4. 하악 연조직점을 종속변수로, 하악 경조직점을 독립변수로한 회귀분석에서 경조직 변화와 연조직 변화 사이의 높은 상관관계가 있다고 하여도 이를 정확하게 예측하기 어렵다는 것을 알 수 있었으며, 연조직 두께와 수평이동사이에는 통계적 유의성이 없었다.
Background: We evaluated change in the mandibular condyle after orthognathic surgery using cone-beam computed tomography (CBCT) in patients with facial asymmetry. Methods: Thirty patients with skeletal class III malocclusion and mandibular prognathism or facial asymmetry were classified into two groups according to the amount of menton deviation (MD) from the facial midline on anteroposterior (AP) cephalogram: group A (asymmetry, MD ≥ 4 mm; n = 15) and group B (symmetry, MD < 4 mm; n = 15). Position and angle of condylar heads on the axial, sagittal, and coronal views were measured within 1 month preoperatively (T0) and postoperatively (T1) and 6 months (T2) postoperatively. Results: On axial view, both groups showed inward rotation of condylar heads at T1, but at T2, the change was gradually removed and the condylar head returned to its original position. At T1, both groups showed no AP condylar head changes on sagittal view, although downward movement of the condylar heads occurred. Then, at T2, the condylar heads tended to return to their original position. The change in distance between the two condylar heads showed that they had moved outward in both groups, causing an increase in the width between the two heads postoperatively. Analysis of all three-dimensional changes of the condylar head positions demonstrated statistically significant changes in the three different CBCT views in group B and no statistically significant changes in group A. Conclusions: There was no significant difference between the two groups in condylar head position. Because sagittal split ramus osteotomy can be performed without significant change in symmetrical and asymmetrical cases, it can be regarded as an effective method to stabilize the condylar head position in patients with skeletal class III malocclusion and mandibular prognathism or facial asymmetry.
합판과 유리섬유강화플라스틱을 조합하여 적층 후 $1.96N/mm^2$의 압력으로 $150^{\circ}C$에서 1시간 고밀화시킨 유리섬유 강화플라스틱 적층판을 제작하였다. 제작된 5가지의 유리섬유강화플라스틱 적층판을 각각 기둥재와 접하는 집성재에 부착하여 부분보강보부재를 제작하였다. 더불어 합판과 시트형 유리섬유강화플라스틱을 적층한 보강적층목재핀과 유리섬유로 보강한 원통형 단판적층기둥재로 기둥-보 접합부를 제작하였다. 기준시험편으로는 원주목과 집성재로 제작한 보부재, 드리프트핀을 사용한 접합부를 제작하여 모멘트 저항 내력을 평가하였다. 시험결과 기준시험편과 비교하여 부분보강보부재를 사용한 시험체들이 평균 1.8배 높은 내력성능이 측정되었다. 모든 부분보강보부재와 원통형 단판적층기둥재에는 파단이 발생하지 않았으며 접합부의 인성과 강성이 모두 양호하게 측정되었다. 부분보강보부재의 보강효과는 시트형 유리섬유강화플라스틱이 직물형 유리섬유강화플라스틱으로 보강한 적층판보다 양호한 보강효과를 보였으며, 시트형 유리섬유강화플라스틱을 각층에 삽입한 적층판이 접합내력과 변형각 모두 양호하여 보부재의 부분보강에 적합한 것을 확인하였다.
본 연구에서는 이종경량재료의 마찰교반용접을 모사할 수 있는 유한요소 해석모델을 개발하고, 이를 통해 기초분석과 실용적 적용 가능성에 대해 고찰하였다. Coupled Eulerian Lagrangian 에 기반한 유한요소모델을 구성하였으며, 해석 모델은 외연적 시간적분을 이용하여 열-온도, 변위-응력 물리계로 이루어진 다중 물리계를 복합적으로 계산하며, 용접툴 표면과 피용접 재료 간 마찰, 극심한 소성변형으로 인한 열에너지 발생, 그리고, 밑면을 통한 열에너지 소산 등 열발생원과 열전달 메카니즘이 모두 고려되었다. Al6061T6와 AZ61 판재의 맞대기용접을 고려하였으며, 주요 용접변수인 용접 속도와 용접툴 회전속도를 변화시킨 세 가지 조건에 대해 해석을 실시하였다. 각 해석은 피용접물의 온도분포, 결함의 분포, 소성변형률 분포가 출력이 가능하였다. 구축한 모델을 이용한 해석 결과 알루미늄보다는 마그네슘부에서 더 높은 온도가 발생하였으며, 회전속도가 커질수록 최대 온도가 증가하기보다는 알루미늄쪽으로 높은 온도가 분산되어 가는 경향을 보였다. 또한, 회전속도가 커질수록 피용접물 재료가 위로 올라오는 플래시 결함의 경향 예측이 가능하였으나, 툴 주변 결함 형성예측은 메시가 세밀하지 못하여 정확한 결과를 산출하기에는 부족하다고 볼 수 있다. 본 모델은 마찰교반용접 중 발생 가능한 여러 물리계의 여러 물리적 현상을 실제에 가깝게 반영하고 있으며, 실험적으로 밝히기 어려운 기초 분석에 응용될 수 있으나, 1달이 넘는 해석소요시간을 감안하면 실용적으로 최적의 용접조건 도출에 응용되기는 어렵다고 판단된다.
건축 구조물의 내진 설계는 탄성 정적 방법에 기초하고 있으나, 강진시 구조물의 실제 거동은 비탄성 동적이기 때문에 설계 규준의 적합성을 판단하기 위해서는 비탄성 동적 해석이 요구된다. 본 논문에서는 철근 콘크리트 특수 모멘트 저항 골조 건물을 선택하여 IBC 2003에 따라 설계한 후, 선택된 부재들의 최대 소성 회전, 소산 에너지를 구하여, 건물의 비탄성 거동이 규준에서 의도한 거동을 보이는 지를 검토함과 동시에 층간변위률 요구값을 구하여 설계 한도를 만족하는 지를 조사하였다. 더불어 비횡력 저항 시스템인 내부 모멘트 저항 골조의 해석시 포함 여부의 영향도 함께 조사하였다. 해석 결과 IBC 2003에 의해 설계된 건물은 규준이 의도한 비탄성 거동을 보여주었으며 층간변위률 또한 설계한도를 만족하였다. 그리고, 내부 모멘트 저항 골조는 지진 해석 결과에 중요한 영향을 미치므로 해석 모델에 반드시 포함되어야 함을 알수 있었다.
The slim-floor solution provides an efficient alternative to the classic slab-over-beam configuration due to architectural and structural benefits. Two deficiencies can be identified in the current state-of-art: (i) the technique is limited to nonseismic applications and (ii) the lack of information on moment-resisting slim-floor beam-to-column joints. In the seismic design of framed structures, continuous beam-to-column joints are required for plastic hinges to form at the ends of the beams. The present paper proposes a slim-floor technical solution capable of expanding the current application of slim-floor joints to seismic-resistant composite construction. The proposed solution relies on a moment-resisting connection with a thick end-plate and large-diameter bolts, which are used to fulfill the required strength and stiffness characteristics of continuous connections, while maintaining a reduced height of the configuration. Considering the proposed novel solution and the variety of parameters that could affect the behavior of the joint, experimental and numerical validations are compulsory. Consequently, the current paper presents the experimental and numerical investigation of two slim-floor beam-to-column joint assemblies. The results are discussed in terms of moment-rotation curves, available rotational capacity and failure modes. The study focuses on developing reliable slim-floor beam joints that are applicable to steel building frame structures located in seismic regions.
Seismic design codes are developed mainly based on the observation of the behavior of structures in the high seismicity regions where structures may experience significant amount of inelastic deformations and major earthquakes may result in structural damages in a vast area. Therefore, seismic loads are reduced in current design codes for building structures using response modification factors which depend on the ductility capacity and overstrength of a structural system. However, structures in low seismicity regions, subjected to a minor earthquake, will behave almost elastically because of the larger overstrength of structures in low seismicity regions such as Korea. Structures in low seismicity regions may have longer periods since they are designed to smaller seismic loads and main target of design will be minor or moderate earthquakes occurring nearby. Ground accelerations recorded at stations near the epicenter may have somewhat different response spectra from those of distant station records. Therefore, it is necessary to verify if the seismic design methods based on high seismicity would he applicable to low seismicity regions. In this study, the adequacy of design spectra, period estimation and response modification factors are discussed for the seismic design in low seismicity regions. The response modification factors are verified based on the ductility and overstrength of building structures estimated from the farce-displacement relationship. For the same response modification factor, the ductility demand in low seismicity regions may be smaller than that of high seismicity regions because the overstrength of structures may be larger in low seismicity regions. The ductility demands in example structures designed to UBC97 for high, moderate and low seismicity regions were compared. Demands of plastic rotation in connections were much lower in low seismicity regions compared to those of high seismicity regions when the structures are designed with the same response modification factor. Therefore, in low seismicity regions, it would be not required to use connection details with large ductility capacity even for structures designed with a large response modification factor.
공장생산으로 신속한 시공이 가능한 모듈러 시스템은 하중저항 방식에 따라 보-기둥 프레임식의 개방형 모듈러 시스템과 패널 및 스터드로 이뤄진 폐쇄형 모듈러 시스템으로 구분할 수 있다. 그 중 개방형 모듈러 시스템은 폐쇄형 단면형상으로 모듈간 접합이 어려우며, 특정부분의 하중 집중현상으로 국부좌굴이 발생하여 내력이 저감될 가능성이 있다. 본 연구에서는 기존 모듈러 시스템의 문제점을 해결하기 위하여 절곡형 단면 안에 콘크리트를 채운 합성단면을 사용한 모듈러 시스템을 제안하였다. 제안된 시스템의 내진 성능 평가를 위해 ATC 40의 능력스펙트럼 해석법을 사용하였으며, 일반적인 모듈러시스템의 결과와 비교하여 성능을 검증하였다. 해석결과에 따르면 성능점에서 합성단면을 사용한 모듈러시스템의 소성힌지 갯수 및 변형량이 적게 나타났다. 이를 토대로 제안된 합성단면의 내진성능이 기존 부재 보다 우수 것으로 판단하였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.