• International Journal of Naval Architecture and Ocean Engineering
• /
• 제12권1호
• /
• pp.691-698
• /
• 2020

In this study, the effects of hydrodynamic interceptors on a high-speed vessel were investigated to identify the operating principle based on experiments. Model tests were performed using a high-speed towing carriage. The resistance, trim and rise of Center of Gravity (CG) of the high-speed vessel were measured for various ship speeds and interceptor heights. As the interceptor height increased, the trim and rise of CG were reduced. In order to quantitatively analyze these phenomena, the pressure at the stern bottom was measured using tactile sensors. The reliability of the measured results from the tactile sensors was verified through repeat tests. The pressure on the stern bottom increased in proportion to the interceptor height, as the interceptor partially blocked the flow there. Then, the trim was reduced. However, as the ship speed increases, the pressure at the location close to the interceptor decreases when the interceptor height is small, leading to increased trim. Therefore, the interceptor height for running attitude control should be carefully determined considering multiple factors in the operating condition of the high-speed planing hull.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제9권3호
• /
• pp.305-314
• /
• 2017

Asymmetric planing hulls are often used on high-speed catamarans. In this study, a linearized potential-flow method is applied for modeling steady hydrodynamics of single asymmetric hulls and their catamaran setups. Numerical results are validated with available experimental data and empirical correlations. Parametric calculation results are presented for the lift coefficient and the center of pressure for variable hull geometry, spacings, and speed regimes. The lift coefficient is found to increase at smaller hull spacings and decrease at higher Froude numbers and higher deadrise angles.

• 해양환경안전학회:학술대회논문집
• /
• 해양환경안전학회 2017년도 공동학술발표회
• /
• pp.123-123
• /
• 2017

• 한국항해항만학회지
• /
• 제36권3호
• /
• pp.157-162
• /
• 2012

활주형선은 고속 운항시 선저에 동적압력을 발생시켜 선체를 부상시켜 침수표면적을 감소시킴으로서 저항이 감소하게 되어 고속의 항주가 가능하게 된다. 또한, 활주형선 선저부에 공기공급을 유도하면 고속 주행시 선저 공기공급에 따른 접수면 감소로 인하여 전체저항 감소에 따른 속도향상과 연비절감 효과가 있다. 이에, 본 논문에서는 고속 모형시험이 가능한 실 해역모형시험기법을 이용하여 고속 활주형선을 대상으로 선저부에 공기공급을 유도하여 침수표면적 감소에 따른 저항성능 개선을 위해 공기공급 유무에 따른 고속 활주형선의 저항특성을 비교, 분석하였다. 시험결과, 선저 공기공급 활주형선이 공기공급이 없는 선형에 비해 저항감소 효과가 현저하게 나타나는 것을 확인할 수 있었다.

• 한국항해항만학회지
• /
• 제32권10호
• /
• pp.759-764
• /
• 2008

활주형선이 수면 위를 활주하여 고속이 가능하기 위해서는 특별하게 설계되어 진다. 대부분의 활주형선은 충격하중을 줄이고 황요, 종요 등의 운동성능을 개선시키기 위하여 스프레이 스트립을 설치하며, 고속에서는 파형개선과 양력발생으로 스프레이저항과 마찰저항이 감소되는 것으로 알려져 있다. 이에, 본 논문에서는 모형시험을 통하여 스프레이 스트립의 부착 유무에 따른 고속 활주형선의 저항특성을 비교, 분석하였으며, 시험결과, 스프레이 스트립 부착 고속 활주형선이 미 부착 선형에 비해서 $3.0{\sim}5.0%$의 저항감소 효과를 확인할 수 있었다.

• 한국해양공학회지
• /
• 제22권4호
• /
• pp.84-89
• /
• 2008

It is hard to find experimental data for a model test of small high-speed planning boats. It is difficult to verify the performance seen in a model test for a high-speed boat because the ship-model scale-ratio is very small and the flow velocity of the circulating water channel and the X-carriage speed of the towing tank are restricted. Therefore most hull-form designs for high-speed small boats depend on the sea-trial test result for similar boats or evaluation through numerical calculations. This study investigated the anti-rolling effect of the stern sub-body in a 50-knot doss planning boat. To carry out this work, new model test procedures were set up in the actual sea. Using this method, the anti-rolling effect of the stern sub-body was investigated. A stern sub-body attached to a planning boat was proved to be effective in reducing the roll and pitch angle.

• 해양환경안전학회:학술대회논문집
• /
• 해양환경안전학회 2017년도 공동학술발표회
• /
• pp.128-128
• /
• 2017

• Journal of Ship and Ocean Technology
• /
• 제2권1호
• /
• pp.1-12
• /
• 1998

A method to predict the dynamic roll stability of hard-chine planing craft is presented. Starting with the equation of motion, an equation governing small roll perturbations is developed. The roll restoring moment acting on the hull is evaluated by considering “static”and dynamic contributions. The contribution of rudders and skegs, which is significant for this type of craft, is also determined. A worked example is presented to show how the method can be used to find the maximum center of gravity height for transverse stability.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2003년도 추계학술대회 논문집
• /
• pp.177-181
• /
• 2003

Despite various forms have been developed and applied to ship hull forms, the superiority of hard chine type over other forms of fishing boat has been recognized so far. As one of the ways of forms for new concept fishing boat, this paper presents the result of a performance evaluation for newly developed forms of hull, appendage and deck house, which features that have esthetic forms.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제5권1호
• /
• pp.161-177
• /
• 2013

High-speed vessels require good resistance and seakeeping performance for safe operations in rough seas. The resistance and seakeeping performance of high-speed vessels varies significantly depending on their hull forms. In this study, three planing hulls that have almost the same displacement and principal dimension are designed and the hydrodynamic characteristics of those hulls are estimated by high-speed model tests. All model ships are deep-V type planing hulls. The bows of no.2 and no.3 model ships are designed to be advantageous for wave-piercing in rough water. No.2 and no.3 model ships have concave and straight forebody cross-sections, respectively. And length-to-beam ratios of no.2 and no.3 models are larger than that of no.1 model. In calm water tests, running attitude and resistance of model ships are measured at various speeds. And motion tests in regular waves are performed to measure the heave and pitch motion responses of the model ships. The required power of no.1 (VPS) model is smallest, but its vertical motion amplitudes in waves are the largest. No.2 (VWC) model shows the smallest motion amplitudes in waves, but needs the greatest power at high speed. The resistance and seakeeping performance of no.3 (VWS) model ship are the middle of three model ships, respectively. And in regular waves, no.1 model ship experiences 'fly over' phenomena around its resonant frequency. Vertical accelerations at specific locations such as F.P., center of gravity of model ships are measured at their resonant frequency. It is necessary to measure accelerations by accelerometers or other devices in model tests for the accurate prediction of vertical accelerations in real ships.