• Journal of Ocean Engineering and Technology
• /
• v.31 no.5
• /
• pp.335-339
• /
• 2017

This study investigated the sea trial performance of a wave piercing high speed planing hull (WPH). The bow shape of the boat is sharp, and it has no chine or spray strip like a normal planing boat. The skeg is attached to the bottom of the boat in the longitudinal direction from the bow to the stern. The speed performance was analyzed as the speed dropped in a wave, and the seakeeping performance was compared with that of a planing boat with a similar velocity coefficient by measuring the vertical acceleration of the bow in the wave. The turning circle was compared with Lewandowski's estimation for a planing boat. As a result of this study, it was confirmed that the velocity drop of the developed WPH was not large in a wave, and the vertical acceleration was greatly reduced compared with that of a normal planing boat. The turning circle was somewhat larger than the estimated results for a planing boat, but the overall tendency was the same.

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.3
• /
• pp.335-342
• /
• 2009

Motion characteristics of a planing craft are sensitively changed according to its weight and longitudinal center of gravity. In this paper, planing craft model tests were performed in calm water for various test conditions and Froude numbers. Sinkage and trim were measured to analyze the relations between the attitudes of a planing craft and the weight and center of gravity of it. Theoretical formula for the prediction of the attitudes of a prismatic planing hull was modified so that it can be applied to the prediction of the attitudes of a non-prismatic planing hull, and the calculation results by the modified formula were in good agreements with the experimental data.

• Journal of Ocean Engineering and Technology
• /
• v.11 no.3
• /
• pp.89-94
• /
• 1997

In the design of high speed fishing vessel, its hull form has to be decided from a view point of resistance and propulsion performance without negelction of seakeeping characteristics. In spite of many efforts, the performance improvement by hull form itself has its limitations, specially for high speed craft. In this paper, the development of performance of resistance and seakeeping improving appendage for high speed planing hull on behalft of the hull form of fishing vessel has been introduced. The developed appendage verified its effectiveness in the full scale test.

• Journal of the Society of Naval Architects of Korea
• /
• v.56 no.1
• /
• pp.23-33
• /
• 2019

Unmanned Surface Vehicle (USV) is being developed to do maritime survey and maritime surveillance at Korea Research Institute of Ships & Ocean engineering (KRISO). The goal is that USV should be operated at the maximum speed of 45 knots and it should be operated at sea state 4. Therefore the planing hull of USV should be excellent in resistance performance and manoeuvring performance. It is needed to check its performance using Experimental Fluid Dynamics (EFD), Computational Fluid Dynamics (CFD) or analytic method before designing the hull. In this study, resistance performance was analyzed by EFD and CFD. EFD with heave and pitch was performed at high speed towing system in Seoul National University. CFD was performed using SNUFOAM based on openFOAM with dynamic mesh to calculate running attitudes. The results of CFD were compared with EFD results. The results of CFD were resistance, running attitudes and wave height. The flow distribution and pressure distribution were also analyzed. The results of numerical resistance was under estimated than EFD. Even though the results of CFD have a slight limitation, it can be successfully used to estimate the resistance performance of planing hull. In addition it can be used as a supplement for EFD results.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.23 no.3
• /
• pp.320-329
• /
• 2017

In this research, we have calculated characteristics of wave-piercing high-speed planing hull, by using a RANS solver and overset grid method, for comparing with experimental measurements of that and simulating with several appendages, since the computed results of commercial CFD code look reasonable for the prediction of the performances of planing hulls on calm water in planing conditions. As a result, it is confirmed that the dynamic instability phenomena in pitch and heave motions (porpoising) occurred after a certain $Fn_V$, and effectively suppressed using some of appendages, especially the 0.5L spray rail is suppressed to 24-55 % in the pitch motion and 33-55 % in the heave motion. In spray phenomenon, 1L hard chine suppress spray effectively and it is effective to set the angle of appendages to be less than $0^{\circ}$ in order to suppress wave.

• Journal of the Society of Naval Architects of Korea
• /
• v.42 no.4 s.142
• /
• pp.341-349
• /
• 2005

With increasing demands of high speed transportation, recently a lot of high speed marine vehicles, such as SWATH, semi-planing craft, planing craft, hydrofoil craft, SES and so on, have been paid attention especially in high speed region over the Froude number 0.5. The resistance characteristics of the vehicles should be experimentally evaluated in the towing tank. At the Seoul National University, a light-weight cantilever type towing carriage was devised and installed in the towing tank. Wireless measurement devices were also provided for appropriate data acquisition during high-speed towing tests. With the new carriage system, a series of model tests were performed to investigate the hydrodynamic characteristics of a stepped planning hull in the towing tank and the resistance performances of the hull are introduced in this report.

• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.5
• /
• pp.401-414
• /
• 2018

Planing hull type ships are often equipped with interceptor or trim tab to improve the excessive trim angle which leads to poor resistance and sea keeping performances. The purpose of this study is to design a controller to control the attitude of the ship by controllable stern interceptor and validate the effectiveness of the attitude control by the towing tank test. Embedded controller, servo motor and controllable stern interceptor system were equipped with planing hull type model ship. Prior to designing the control algorithm, a model test was performed to identify the system dynamic model of the planing hull type ship including the stern interceptor. The matrix components of model were optimized by Genetic Algorithm. Using the identified model, PID controller which is a classical controller and sliding mode controller which is a nonlinear robust controller were designed. Gain tuning of the controllers and running simulation was conducted before the towing tank test. Inserting the designed control algorithm into the embedded controller of the model ship, the effectiveness of the active control of the stern interceptor was validated by towing tank test. In still water test with small disturbance, the sliding mode controller showed better performance of canceling the disturbance and the steady-state control performance than the PID controller.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.6 no.4
• /
• pp.867-875
• /
• 2014

Planing crafts were specifically designed to achieve relatively high speeds on the water. When a planing craft is running at high speed, dynamic pressure on the bottom makes the boat rise on the surface of the water. This reduces the area of the sinking surface of the boat to increase air resistance. Air resistance means the resistance that occurs when the hull and deck house over the surface of the water come in contact with the air current. In this paper, we carried out a CFD numerical analysis to find optimal deck houses that decreased air-resistance on the water when planing crafts are running at high speed. We finally developed the deck house shape of high-speed planing crafts that optimally decreased air resistance.

• Journal of the Society of Naval Architects of Korea
• /
• v.31 no.3
• /
• pp.100-111
• /
• 1994

This study was carried out for understanding the characteristics of the spray around high speed vessels. Prismatic planing hull made of an acrylate board was used to the tests. The distribution of local spray velocity were estimated from the analysis of the spray visualization. A new test system for measuring the spray thickness is proposed, and was used to estimate the local spray thickness in the model. The pressure distributions on the bottom of the hull are measured and integrated to estimate the pressure drag of the model in the towing tests. Finally. the spray drag/lift component is separated from the total drag/lift on the prismatic hull. These test results show that the spray drag component on high speed vessels is relatively large and important in total drag.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2005.06a
• /
• pp.90-96
• /
• 2005

This paper presents the results of the reliability analysis of PAU (Preliminary Assembly Unit) seat of the floating Production Storage and Off1-loading Unit (FPSO) The main aim of the analysis was to demonstrate that a sufficient safety of structural members is guaranteed against PAU loads, internal and external pressure, and hull girder moments. Topside loads for PAU design are based on owner's request. According to the seat type, topside loads are classified into maximum values of same seat type for design efficiency. Totally, 26 loading cases for each model are used for this analysis with the combination of the reactions of PAU loafing and the hull girder bending moments according to LR offshore (2). The analysis results are evaluated according to the acceptance criteria for yielding given in LR offshore and guidance note (3) and The panel buckling resistance is verified by LR offshore and SDA (4). For 900,000 bbls FPSO, the PAU support foundation analysis using 3-D F.E. model is carried out to verify the structural adequacy of PAU foundation and structure members in way of PAU. The modified structures in way of PAU support are safe against considered load cases and all stresses in way of PAU support are within design criteria.