• 수산해양기술연구
• /
• 제51권3호
• /
• pp.285-294
• /
• 2015

As a "kind of" mature ship form, planing hull has been widely used in military and civilian areas. Therefore, a reasonable design for planing hull becomes more and more important. For planing hull, resistance and trim are always the most important problems we are concerned with. It affects the planing hull's economic efficiency and maneuverability very seriously. Instead of the expensive towing tank experiments, the development of computer comprehensive ability allows us to previously apply computational fluid dynamics(CFD)to the ship design. In this paper, the CFD method and Goal Driven Optimization (GDO) were used in the estimations of planing hull resistance and running attitude to provide a possible method for performance computation of planing hull.

• 대한조선학회지
• /
• 제2권1호
• /
• pp.9-14
• /
• 1965

Ship designers make every efforts to get faster ships in accordance with the development of the Naval Architecture. But for the speed lying over factor length ratio 2.5-3.0, we could put a powerful engine into the conventional round bottom displacement type vessels, but it is very difficult in view point of economy, weight and volume. The principal cause of these speed obstacles is the wave making resistance and researchers are trying to decrease this resistance. One of the resolving ways, planing hulls were applied to small high boats. Planing hull's advantage is not restricted to speed, but the workmanship of the planing hull is easier than those of displacement type vessels of round bottom. Planing hull, therefore, are widely applicable to the intermediate speed boats, which don't have enough high speed to take planing advantage, as well as high speed boats. We will discuss related phenomena of the planing hull in details and this paper we particularly interested in the interjection point(speed length ratio 3.0-3.5 by Mr. D. De Groots) between semi-planing and full planing hulls on the resistance characteristic curve. The paper by Prof. Keuck Chun Kim, "Some Characteristics of Straight Framed V-bottom Hull Forms", Journal of the society of Naval Architects of Korea, Vol.1, No.1, Dec.5, 1964, is referred to the V-bottom hull forms belonging to low speed region and determines practical applicable limit of the speed length ratio combined with construction costs, under which are still used by large commercial vessels. This is the interesting contrast between his and authors. We will further discuss the speed length ratio which is considered as a beginning point to planing effect. For this analysis, we choose 3 model ships: Model (1) and (2) have the same principal dimensions, model 3 varied dimension. Model (1) is full-planing hull, (2) is semi-planing hull and (3) is complete planing hull. They are aimed to collect proper design data for purposed ships.

• 한국해안·해양공학회논문집
• /
• 제30권3호
• /
• pp.95-102
• /
• 2018

고속 주행시 마찰저항을 감소시키기 위해 선체의 선저부분의 모양을 변화시키는 등 최근 관련 분야의 개발이 이루어지고 있는 바, 본 개발에서는 기하학적으로 고속활주선의 스텝 단면을 유선형(streamlined type) 구조로 제작해 침수 표면적에 의한 마찰저항의 최소화를 목적으로 준비하였다, 본 개발의 목적은 어업의 각종 위급상황 및 안전성을 고려한 고속활주선의 구조설계를 기반으로 하여 어업의 특수성 및 작업특성(어군 추적 및 어획물 출하)을 고려한 최적선형으로서 유선형 마찰저감형 고속활주선을 제작하는데 그 목표가 있으며, 이 과정에서 제작된 성과물에 대한 성능평가를 수행하여 정량적 목표치를 확보하고자 함에 본 기술개발 논문의 소개 배경이 있다.

• 한국시뮬레이션학회논문지
• /
• 제27권2호
• /
• pp.83-90
• /
• 2018

본 연구에서는 선형의 기본 파라메타가 주어졌을 때, 선형 최적화를 통하여 고속으로 주행하는 활주선의 저항성능을 개선하는 기법을 제안하였다. 먼저 선행연구 된 활주선형을 기준 선형으로 채택한 뒤, 선형 변경지점을 정의해 설계변수로 하여 최적화 문제를 수립하였다. 계산 효율을 위하여 탐색공간을 이산화하고, 최적화 문제를 풀기위하여 DPSO(Discrete binary version of Particle Swarm Optimization) 알고리즘을 사용하였다. 최적화 수행 후 기준 선형과 수정 선형의 목적함수 출력의 비교를 수행하였고, 이를 통해 고속영역에서의 저항성능의 개선을 확인하였다.

• 수산해양기술연구
• /
• 제41권3호
• /
• pp.222-226
• /
• 2005

A series of model tests carried out at the CWC of WJFEL for the purpose of prediction of resistance for the performance and improvement of resistance by attaching appendage for the ship of 50 knots class planing hull. The resistance performance evaluation has been carried out for the bare hull and for the appendage hull with two different depth of vertical type wedges. In the bare model test, trim and sinkage is calculated for the planing hull and the resistance is calculated. For minimizing the resistance, wedge appendage is attached and tested. Analysis and tests shows that for a 12.5mm wedge, resistance is minimum and overall power tallied to 5636ps.

• 한국기계연구소 소보
• /
• 통권13호
• /
• pp.87-98
• /
• 1984

An experimental study carried out to predict the performance characteristics of a high speed planing boat at the two displacements whose hull form shows hard chines form transom to bow. In the resistance test the planing hull model was porpoising at and above 30 knots for both displacements of 30 tons and 24 tons. A small stern wedge was newly designed and attached across hull bottom. The planing hull model with the stern sedge did not show any porpoising up to the speed of 45 knots for both displacements and it analysed results shows the improvement of resistance performance and planing performance comparing with those of original hull form; i.e. for displacement of 30 tons the effective power and trim angle were reduced by 18.9% and 5.71 degrees at the speed of 28 knots, and for the displacement of 24 tons the effective power and trim angle were reduced by 23.63% and 4.37 degrees at the speed of 28 knots, respectively.

• 대한조선학회논문집
• /
• 제55권5호
• /
• pp.431-437
• /
• 2018

The running attitude of a planing hull is determined by the pressure distribution on the hull bottom, and it significantly affects hydrodynamic performance of the ship, i.e., resistance, maneuverability, and seakeeping ability. Therefore, it is essential to investigate pressure distribution on the hull bottom in order to improve hull design. In the present study, a novel pressure measurement system using tactile sensors was introduced for a planing hull. The test model was a 23 m-class planing hull with a hard chine. The pressure measurement showed that the pressure at the transom was lower than the atmospheric pressure, owing to flow separation at the transom.

• 수산해양기술연구
• /
• 제40권1호
• /
• pp.17-22
• /
• 2004

This study was carried out at the CWC of Chosun university for the purpose of resistance performance improvement of planing hull, and the results of the tests were confirmed cooperatively with WJFEL. G/T 100 ton class planing hull form was selected, and the improvement of hull form including appendages were performed by using some model test techniques. The model test scope comprises resistance relative tests including wave profile observation, trim and sinkage measurement and flow visualization tests at full load and trial conditions for one bare hull and for two appended hulls. The final wedge and spray strip combined with improved hull form showed about 1.0 knot speed improvement at both of full and trial conditions, and outstanding improvement for fore wave phenomena.

• 한국해양공학회지
• /
• 제24권4호
• /
• pp.59-65
• /
• 2010

This study presents the design procedure for optimizing the semi-planing hull form, including appendages, using numerical and experimental methods. Four different referenced semi-planing hull forms were compared to determine their hydrodynamic performances, and one of the hull forms was modified for optimum operation at high-speed conditions (0.4 < $F_{NL}$ < 0.9). The optimized, semi-planing hull form was tested in the towing tank to investigate its resistance characteristics. Also, the results of the model tests with differing design parameters were used to choose the stern wedge and the spray strip to improve the hydrodynamic performance at high speeds.

• 수산해양기술연구
• /
• 제44권1호
• /
• pp.68-74
• /
• 2008

This study is concerned with the development of the basic planing hull form of small fishing boat in 25 knots high speed. A series of model test to determine the optimum performance hull form of actual fishing boat with 10 gross tonnage was carried out for 5 models made available planing hull form in the circulation water channel. Model test was performed with the resistance test to study the hydrodynamic characteristics of model ships and the sinkage and trim measurement to investigate the stability of model ships and also the wave pattern observation to analyze the effectiveness of model ships. As the result, the planing hull form of P-4 with deep V type bow can be derived as the best hull form with good performance especially in ship's resistance efficiency showing less residual resistance and sinkage and trim and the spray effect, etc..