• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.939-940
• /
• 2006

An integrated inductor using the low-temperature co-fired ceramics(LTCC ) technology for low-power electronics was fabricated. In the inductor NiZn ferrite sheet(${\mu}_r=230$), was embedded to increase inductance. The inductor has Ag spiral coil with 14 turns($7turns{\times}2layers$), a dimension of 0.6mm in width, 10um in thickness, and 0.15mm pitch. To evaluate the inductance, including the parasitic resistance, the fabricated inductor was calculated and measured. It was confirmed that calculated values were very close to the measured values. Finally as an application of the LTCC integrated inductor to low power electronic circuits, a LTCC buck DC/DC converter with 1W output power and up to 0.5MHz switching frequency using the inductor fabricated was develop.

• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.35T no.3
• /
• pp.9-14
• /
• 1998

The speech recognition on long vowels are carried out by electric circuits. A level compressor is able to transform the wave of voice to serial pulses. The obtained pulses have informations to distinguish the vowels. The sampling of the pulses is carried out by the register which picks up a series of serial signals in a pitch of a vowel as an unit. The timing control pulses such as sampling pulses are generated by using peak pulses in the speech wave. The parallel data in the register assign the phonetic symbol by means of the decision making circuit which carries out the IF-THEN rule.

• Journal of Institute of Control, Robotics and Systems
• /
• v.3 no.3
• /
• pp.238-243
• /
• 1997

A new transfer alignment algorithm using the velocity and the quaternion partial matching methods is proposed to reduce the effect of a ship's Y-axis flexure on the performance of azimuth error estimation of Kalman filter. The simulation results show that it can significantly reduce the effect of Y-axis flexure on error estimation by the transfer alignment algorithm. As its results, azimuth transfer alignment error is reached up to 3 mrad under proper roll and pitch attitude motion of the ship.

• Proceedings of the IEEK Conference
• /
• 2007.07a
• /
• pp.235-236
• /
• 2007

CCD(Charge-Coupled Device) 혹은 CMOS (Complementary Metal Oxide Semiconductor)와 같은 소자를 이용하여 빛을 전기적 신호인 Image로 재구성하는 촬상소자(Color Capture Device)는 촬영환경이 어두워지면 Dynamic Range가 작아지고, Noise가 상대적으로 심해진다[1][2]. 본 논문에서는 촬영 환경이 어두울 때, Resolution을 Preserving하는 Pixel Pitch가 큰 촬상 소자와 Motion Blur를 억제하는 Exposure Time이 긴 촬상 소자의 조합을 신호처리로 구현하여, 신호의 Power를 향상시켜 Dynamic Range를 키우고 Noise의 Boost-up을 억제하여 SNR(Signal to Noise Ratio)을 향상시키는 방식으로, 촬상 장치의 감도를 향상시켜 화질을 개선하는 방법을 제안한다.

• Journal of ILASS-Korea
• /
• v.13 no.1
• /
• pp.9-15
• /
• 2008

This experimental study was carried out to examine the heat transfer characteristics of impinging air jet on a flat plate with a set of right angled triangle rods. Each right angled triangle rod in the array was positioned normal to the flow direction and parallel to the flat plate surface. The clearances from a right angled triangle rod to flat plate surface (C=1, 2 and 4 mm) and the distance from nozzle exit to flat plate (H=100 and 500 mm) were changed for the pitch between each right angled triangle rods (P=40 mm). As a result, heat transfer shows best performance at the clearance of C=1 mm, in case clearance changed, and the average heat transfer enhancement rate increased up to 47% compared to the result of a flat plate without a right angled triangle rod.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.12 no.1
• /
• pp.37-40
• /
• 1975

Heave and pitch amplitude and phase lag, relative vertical displacement, velocity and acceralation at bow as bow motion and wave exciting force and moment of a DWT 260,000 ton class tanker in the regular head wave have been calculated. All the calculations have been made by the computer program SD08 of Seoul National University. As the results it is cleared heave amplitude and acceralation have large value in the ballast condition and low Froude-number than full load condition and higher Froude numer as for as the $\frac{\lambda}{L}$ is lower than near around 1.0, however they have quite large values as $\frac{\lambda}{L}$ goes up.

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.2
• /
• pp.134.1-134.1
• /
• 2012

The radiation belt structure can be approximately reproduced by a form of diffusion equation, which takes into account the radial diffusion process as well as those in pitch angle and energy. The solution of the equation depends on several factors including initial and boundary conditions, diffusion coefficients, and plasmapause location. In this paper, we have attempted to determine a set of approximate functions for the energetic electron fluxes near the outer edge of the outer belt in terms of solar wind variable. We used the electron flux data from SST onboard the THEMIS spacecraft and determined its correlation with solar wind conditions in a systematic way. The functions were determined separately for different energy channels from ~30 keV up to 719 keV. Our determination of these functions allows us to predict the radial boundary condition for the electron flux, which can be implemented in a forecast model.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.4
• /
• pp.452-460
• /
• 1999

Sawing experiments using a two-arm system have been performed in this work. The two-arm system under consideration of two kinematically-nonidentical arms. A passive joint is inserted at the end-point of one robot in order to increase the mobility up to the motion degree required for sawing tasks. A hybrid control algorithm for control of the two-arm system is designed. We experimentally show that the performance of the velocity and force response are satisfactory, and that one additional passive joint not only prevents the system from unwanted yaw motion in the sawing task, but also allows an unwanted pitch motion to be notably reduced by an internal load control. To show the general applicability of the proposed algorithms, we perform experimentation under several different conditions for saw, such as three saw blades, two sawing speeds, and two vertical forces.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.10
• /
• pp.534-539
• /
• 2006

An integrated inductor using the low-temperature co-fired ceramics(LTCC) technology for low-power electronics was fabricated. In the inductor NiZn ferrite sheet$({\mu}_r=230)$, was embedded to increase inductance. The inductor has Ag spiral coil with 14 turns$(7turns{\times}2layers)$, a dimension of 0.6mm in width, 10um in thickness, and 0.15mm pitch. To evaluate the inductance, including the parasitic resistance, the fabricated inductor was calculated and measured. It was confirmed that calculated values were very close to the measured values. Finally as an application of the LTCC integrated inductor to low power electronic circuits, a LTCC boost DC/DC converter with 1W output power and up to 0.5MHz switching frequency using the inductor fabricated was developed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.4
• /
• pp.211-219
• /
• 2003

The main study experiments to obtain engine torque of the vehicle during performance test of the recent automobile. Torque was measured through the engine dynamometer to produces engine torque of the vehicle but the research method calculated engine torque of the vehicle without the engine dynamometer. The performance of the vehicle receive various running resistance. The study certificates performance of certification before a certification of used vehicle didn't carry out and certificate. This way evaluated on road test and chassis dynamometer The result of the study shows that it is much possible to apply the test. After comparing the engine torque of road driving with that of chassis dynamometer, the results are approximately the same. When rapidly speeded up, the road-load vehicle can pitch in some degrees, which may result in the fluctuations of acceleration, and then affect on the engine torque. Therefore it is confirmed that this method is easier way to measure the performance of vehicles.