• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 말뚝기초 학술발표회
• /
• pp.107-141
• /
• 2000

Large diameter piles can be defined as piles with diameter of at least 0.76 m (2.5 ft). In bridge foundation, large diameter piles have been used as pier foundations and their use has been increased greatly. In this study, static pile load tests for large diameter piles peformed in Kwangan Grande Bridge construction site were introduced. Also, various sensor installation methods for several types of piles (that is, open-ended steel pipe pile, drilled shafts and socketed pipe piles), pipe axial load measuring method, load transfer analysis method and pile load test results (pile-head load - settlement curve, and pile axial load distribution curve along the pile depth) were introduced.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.366-376
• /
• 2008

The model tests of short pile with very small pile length/diameter(L/D) were performed in this paper. Varying the pile diameter, length, and the lateral loading point, the lateral resistance and behavior of very short pile were studied in this model tests. The experimental and analytical results are as follows. The lateral ultimate resistance of short pile in sands was the maximum at the point of h/L=0.75, regardless of pile length/diameter(L/D). As the pile diameter is larger, the lateral ultimate resistance of pile with L/D=1 decreases a little and the lateral resistance increases according to the ratio of pile length/diameter. As the lateral loads are acting on the pile, the displacement of pile head is maximum at the pile top of h/L=0, but minimum at the middle point of the pile. And if the loading point is under the middle of pile, the displacement of pile head occurs oposite in the loading direction, but its magnitude is very small.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 가을 학술발표회 논문집
• /
• pp.390-397
• /
• 2002

In this study, static pile load tests with load transfer measurement for a pile socketed into weathered rocks were performed. Axial load transfers during static pile load test were measured and analyzed. Three large diameter piles socketed into weathered rock were behavior behaved as friction pile.

• 한국지반공학회논문집
• /
• 제33권5호
• /
• pp.37-44
• /
• 2017

본 연구에서는 특정 암반에 근입된 강관말뚝의 거동특성을 분석하기 위하여, 강관말뚝의 직경, 두께 및 길이 조건에 따른 인발, 압축 및 수평재하 시의 시험결과 예측을 위한 3차원 수치해석 연구를 수행하였다. 먼저, 인발재하에 대한 거동특성을 분석한 결과, 동일한 말뚝길이 및 두께와 인발하중 크기를 기준으로 말뚝직경에 반비례하는 인발변위가 나타나는 것으로 확인되었다. 또한 압축재하에 따른 하중-침하 관계를 통하여, 말뚝 직경에 비하여 말뚝의 두께가 하중저항에 대한 효과에 더욱 큰 영향을 미치는 것으로 분석되었으며, 수평하중 재하에 따른 수평변위 관계를 바탕으로 수평하중의 저항효과는 말뚝직경에 의한 영향이 큰 것으로 분석되었다. 따라서 강관말뚝을 이용하여 기초구조물 설계에 따른 재하시험을 위해서는 예비설계 단계에서 말뚝 조건이 거동특성에 미치는 영향을 분석할 필요가 있는 것으로 확인되었다.

• 대한토목학회논문집
• /
• 제33권5호
• /
• pp.1935-1946
• /
• 2013

본 연구에서는 변단면 단일 현장타설말뚝의 거동 특성을 평가하고자 현장재하시험 사례를 분석하였으며, 또한 3차원 유한요소해석을 이용하여 말뚝 내부에서 발생하는 응력을 통해 심도별 휨응력을 산정하였다. 분석 결과, 단일 현장타설말뚝의 변단면 부근에서 휨응력이 집중되어 재료파괴가 발생하기 가장 쉬운 것을 알 수 있었다. 이를 토대로, 단일 현장타설말뚝의 기둥-말뚝 직경비와 수평 균열하중비 관계를 통해 최적의 기둥-말뚝 직경비를 제안하였다. 연구 결과, 최적의 기둥-말뚝 직경비는 기둥-말뚝 직경비와 수평 균열하중비 관계 곡선의 변곡점 부근에서 산정되었으며, 단일 현장타설말뚝 설계에 최적 변단면 특성을 고려한다면 개선된 설계가 이루어질 수 있을 것으로 판단되었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.351-359
• /
• 2010

Large PHC piles with a diameter of 1,000mm or larger were recently introduced for the first time in Korea. This paper presents full-scale static and dynamic pile load tests performed on two 1,000mm PHC piles and two composite piles with steel pipe piles of the same diameter in the upper portion, installed by driving and pre-boring. The objectives of the tests include evaluating pile drivability, load-settlement relation, allowable bearing capacity, and the stability of mechanical splicing element for the composite pile(a.k.a. non-welding joint). The performance of the large diameter PHC piles were thought to be satisfactory compared to that of middle sized PHC piles with a long history of successful applications in the domestic and foreign markets.

• Geomechanics and Engineering
• /
• 제12권6호
• /
• pp.899-917
• /
• 2017

Sixty four tests were performed in a steel tank to investigate the axial responses of piles driven into organic soil prepared at two different densities using a drop hammer. Four different pile materials were used: wood, steel, smooth concrete, and rough concrete, with different length to diameter ratios. The results of the load tests showed that the shaft load capacity of rough concrete piles continuously increased with pile settlement. In contrast, the others pile types reached the ultimate shaft resistance at a settlement equal to about 10% of the pile diameter. The ratios of base to shaft capacities of the piles were found to vary with the length to diameter ratio, surface roughness, and the density of the organic soil. The ultimate unit shaft resistance of the rough concrete pile was always greater than that of other piles irrespective of soil condition and pile length. However, the ultimate base resistance of all piles was approximately close to each other.

• 한국지반공학회지:지반
• /
• 제12권2호
• /
• pp.85-94
• /
• 1996

말뚝직경이 개단말뚝의 폐색정도와 지지력에 미치는 영향을 규명하기 위하여 응력상태와 상대밀도의 조절이 가능한 토조와 직경이 다른 세개의 모형말뚝을 이용하여 모형말뚝실험을 수행하였다. 모형말뚝은 말뚝의 지지력 성분을 분리측정하기 위하여 직경이 다른 두개의 파이프로 만들어졌다. 실험결과에 의하면 말뚝이 완전폐색 상태로 되는 관입깊이는 말뚝직경과 지반의 상대밀도가 증가할수록 커지는 것을 알 수 있었으며, 관입비와 관내토 증분비가 동일하더라도 단위 관내토 지지력은 말뚝의 직경이 커질수록 감소하는 경향을 보였다. 그러나 기존의 지지력 산정식은 말뚝의 관입비나 폐색정도가 동일한 상태에 대하여 관내토 지지력은 말뚝의 직영에 관계없이 일정하거나 직경이 증가할수록 커지는 결과를 주고 있다. 이는 본 연구의 실험결과와 상반되는 것으로서 관내토 지지력의 산정시 말뚝의 폐색정도 뿐만 아니라 크기효과도 고려하는 것이 필요한 것으로 밝혀졌다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 봄 학술발표회 논문집
• /
• pp.185-192
• /
• 1999

It had found that, as a result of cross-hole tonic logging test, concrete was not filled partially within the bottom 2.0 m of the large diameter (Ø= 2,500mm) rock socketed pile, MP20-P11(socket diameter (Ø= 2,200mm), which was a pile among piles group supporting a pier of Kwangan Grand Bridge. The pile was repaired by the combined cement grout injected through the pipes for the cross-hole sonic logging test and the bore holes for core samples. A month after the cement grouting, repairing was checked by coring and cross-hole sonic logging then 3 times of grouting and 2 times of coring were, in turns, peformed, then repairing was completed successfully. The vertical compressive capacity of the repaired large diameter socketed pile was evaluated by several formulas and software ROCKET, and was more conservative than design load (1,882 ton) of MP20-P11. It is expected that, in the case of the battered socketed piles, it could be more reasonable to analyze the behaviors of a battered pile using 3-D model. A 3-D analysis will be peformed in the future study.

• 한국환경복원기술학회지
• /
• 제9권5호
• /
• pp.10-21
• /
• 2006

For analyze of the bearing capacity, skin friction and settlements of pile on axial compressive loading, both Load transfer tests of pile and pile loading test in field have application to commonly before pile installing. A bearing capacity of pile was affected by the characteristics of surrounding ground of pile. Especially, that is very different because of evaluation of settlement due to each soil conditions of ground depths. The ground characteristics using evaluation of bearing capacity of pile through load transfer analysis depends on N values of SPT, and then a bearing capacity of pile installed soft ground and refilled area may be difficult to rational evaluation. An evaluation of bearing capacity on pile applied axial compressive loading was effected by strength of ground installed pile, unconfined compressive strength at pile tip, pile diameter, rough of excavated surface, confining pressure and deformation modules of rock etc and these are commonly including the unreliability due to slime occurred excavation works. Load transfer characteristics considered ground conditions take charge of load transfer of large diameter pile was investigated through case study applied load transfer tests. To these, matrix analytical technique of load transfer using finite differential equation developed and compared with the results of pile load test.