• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.464-464
• /
• 2012

본 연구에서는 DBD (Dielectric Barrier Discharge)방식을 통해 발생된 대기압 plasma를 이용한 Photoresist (PR) Ashing에 관한 연구를 하였다. 사용된 DBD 반응기는 기존의 blank planar plate 형태의 Power가 인가되는 anode 부분과 Dielectric Barrier 사이 공간을 액상의 도전체로 채워 넣은 형태의 전극이 사용 하였으며, 인가 Power는 40 kHz AC 최대 인가 전압 15 kV를 사용 하였고(본 연구에서 인가 power는 30 KHz,전압 14 KV를 고정시킴) 플라즈마를 발생시 라디칼의 활성화를 유지하기 위해 전극 온도가 $180^{\circ}C$ 정하였다. Feeding 가스는 N2, 반응가스로는 CDA(Clean Dry Air), SF6와 CF4가스를 사용 하였으며 모든 공정은 In-line type으로 시편을 처리 하였다. CDA ratio의 경우에 질소대비 0.2%때 이송속도 30 mm/sec 1회 처리 기존 PR ashing은 최대 $320{\AA}$의 ashing 두께를 얻을 수 있었다. SF6와 CDA가스를 같이 반응하는 경우 ratio는 CDA : SF6 = 0.6% : 0.6%에서 PR ashing rate이 $841{\AA}/pass$의 값을 얻을 수 있었고, CDA가스만 첨가하는 경우보다 약2.6배 증가함을 관찰할 수 있었다. CF4 가스를 사용하는 경우 ratio는 CDA : CF4 = 0.2% : 0.2%에서 PR ashing rate이 $687{\AA}/pass$의 값을 얻을 수 있으며 CDA가스만 첨가하는 경우보다 약 2.1배 증가함을 관찰할 수 있었다. 그리고 PR ashing rate가 가스첨가종류와 비율에 따라서 변화함을 관찰하였고 최적조건을 찾기 위해 연구를 진행하였다. 추후 PR ashing rate가 향상을 하기 위해 가스혼합비율 및 stage 온도등 조건을 조절하여 공정최적조건을 얻기 위해 연구를 진행하였다.

• Macromolecular Research
• /
• v.12 no.4
• /
• pp.352-358
• /
• 2004

For their application as one-component photoresists, we prepared epoxy terpolymers containing oxime-urethane and benzophenone groups by the radical polymerization of glycidyl methacrylate (GMA), metha-cryloxyethyl benzophenoneoxime urethane (MBU), and N-(4-benzoyl)phenylmaleimide (BPMI). The terpolymer composition was optimized to provide the most photosensitive photoresist. The photo-decomposition reaction of the oxime-urethane groups in the terpolymer was monitored by UV absorption spectroscopy, and the photo-crosslinking reaction of the epoxy terpolymer was observed by measuring the normalized thickness. The photosensitivity of the epoxy terpolymer increased as the amount of BPMI and MBU units increased up to 16 and 24 mol%, respectively. Among the terpolymers we prepared, terpolymer T-II(contents of GMA, MBU, BPMI are 75, 19, 6.1 mole%, respectively) exhibited the highest photosensitivity ( $D_{c}$ $^{0.5}$ = 430 mJ/$\textrm{cm}^2$) and had a moderate contrast (${\gamma}$$^{p}$ = 1.23). Negative-tone micropatterns having a line width of ca. 10 ${\mu}{\textrm}{m}$ were obtained by developing the system with chloroform.m.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.26 no.2
• /
• pp.55-64
• /
• 2008

We designed a UV-LED exposure system which has 365nm dominant wavelength due to the environment-friendly and economical maskless screen plate making. And the photoresist applied on the screen stretched was exposed without mask by beam projector with UV-LED light source. Then it was developed by air spray with $1.7\;kgf/cm^2$ of injection pressure. The pencil hardness and solvent resistance of curing photoresist film were excellent as those of conventional photoresist film and the maximum resolution of line image formed by maskless screen plate making. was $100{\mu}m$, so we could establish the possibility of environment-friendly maskless screen plate making technology. But the sharpness of the patterns were ${\pm}40{\mu}m$ since the exposure system for maskless plate making has weak light intensity and the diffusion of light.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.152-155
• /
• 2003

Ashing of photoresist was investigated in dielectric barrier discharges in atmospheric pressure by changing applied voltage, frequency, flow rate. we analyzed the plasma by Optical Emission Spectroscopy(OES) to monitor the variation of active oxygen species. Another new peaks of oxygen radical is observed by addition of argon gas. This may explain the increase in ashing rate with argon addition. With the results of Optical Emission Spectroscopy(OES), we can find the optimized ashing conditions. MIS capacitor for monitoring charging damage by the plasma was also studied. The results suggest the dielectric barrier discharges(DBD) can be an efficient, alternative Plasma source for general surface processing.

• Journal of Microbiology and Biotechnology
• /
• v.32 no.5
• /
• pp.672-679
• /
• 2022

Microbial lipases are used widely in the synthesis of various compounds due to their substrate specificity and position specificity. 4-Ethyl malate (4-EM) made from diethyl malate (DEM) is an important starting material used to make argon fluoride (ArF) photoresist. We tested several microbial lipases and found that Photobacterium lipolyticum M37 lipase position-specifically hydrolyzed DEM to produce 4-EM. We purified the reaction product through silica gel chromatography and confirmed that it was 4-EM through nuclear magnetic resonance analysis. To mass-produce 4-EM, DEM hydrolysis reaction was performed using an enzyme reactor system that could automatically control the temperature and pH. Effects of temperature and pH on the reaction process were investigated. As a result, 50℃ and pH 4.0 were confirmed as optimal reaction conditions, meaning that M37 was specifically an acid lipase. When the substrate concentration was increased to 6% corresponding to 0.32 M, the reaction yield reached almost 100%. When the substrate concentration was further increased to 12%, the reaction yield was 81%. This enzyme reactor system and position-specific M37 lipase can be used to mass-produce 4-EM, which is required to synthesize ArF photoresist.

• Journal of the Korean Vacuum Society
• /
• v.18 no.2
• /
• pp.97-101
• /
• 2009

In the modem semiconductor industry, the progress that consumes the most capital and labor is cleansing process. Cleansing process is to remove impurities that can affect the operation of the device and deteriorate its function. Especially, Photoresist (PR) progress that etches the device always requires cleansing at the end of the progress. Also, HDI-PR (High-Dose Ion-implanted Photoresist) created from PR progress is difficult to remove. Thus, in modem IC cleansing, many steps of cleansing are used, including dry and wet cleansing. In this paper, we suggested to combine existing dry-cleansing and wet-cleansing, each represented by plasma cleansing and stripper solution, as Plasma Liquid-Vapor Activation (PLVA). This PLVA method enhances the effect of existing cleansing solution, and decreases the amount of solution and time required to strip. We stripped HDI-PR by activated solution and measured surface hardness and Young's modulus by Nano-indenter. Nano-indenter is the equipment that determines the hardness and the modulus of elasticity by indenting nano-sized tip with specific shape into the surface and measuring weight and z-axis displacement. We measured the change of surface hardness and Young's modulus before and after the cleansing. As a result, we found out that the surface hardness of the sample sharply decreased after the cleansing by plasma-activated PR stripper solution. It can be considered that if physical surface-cleansing process is inserted after this, more effective elimination of HDI-PR is possible.

• Korean Chemical Engineering Research
• /
• v.44 no.5
• /
• pp.498-504
• /
• 2006

The etch rates of photoresist (PR) and the etch selectivity of $SiO_2$ to PR in a high density $CHF_3$ plasma were investigated at different ion-incident angles and bias voltages. A Faraday cage was employed for the accurate control of ion-incident angles. The ion energy was controlled by changing bias voltages. The etch rate of $SiO_2$ continuously decreased with ion-incident angles but the etch rate of PR remained constant up to the middle angle region and decreased afterwards. The etch rates of $SiO_2$ normalized to those at $0^{\circ}$ incident angle changed with the ion-incident angle following a cosine(${\theta}$) curve. On the other hand, the normalized etch rates of the PR changed showing a drastic over-cosine shape in the middle angle region. The etch selectivity of $SiO_2$ to PR decreased with an increase in the ion-incident angle because the etch yields of PR were enhanced by physical sputtering in the middle angle region compared to the case of $SiO_2$ etching. The etch selectivity of $SiO_2$ to PR decreased with an increase in the bias voltage at nearly all ion-incident angles.

• Korean Chemical Engineering Research
• /
• v.43 no.1
• /
• pp.27-32
• /
• 2005

We propose an effective and environmentally friendly dry stripping method using a supercritical carbon dioxide ($SCCO_2$) system modified by a single and multiple cosolvents to remove ion-implanted photoresist and residue from a wafer surface at three different temperatures (97, 148, $200^{\circ}C$) and pressures (200, 300, 400 bar). After high dose of ion implantation the photoresist was not easily removed by using pure $SCCO_2$, but swollen. The $SCCO_2$ system modified by single cosolvents and multiple cosolvents mixed with aprotic solvents could not effectively remove the heavy organics, but swell them. However, the $SCCO_2$ system modified with multiple cosolvent (5%, v/v) composed of DMSO and DIW showed high removal efficiency for ion-implanted photoresists at $97^{\circ}C$ and 200 bar for 30 min (about 80%). In this study it has been shown that the dry stripping method using $SCCO_2$ system modified with multiple cosolvents could replace either plasma ashing or acid and solvent wet bench method and dramatically reduce accompanied chemical usage and disposal.

• Polymer Science and Technology
• /
• v.1 no.6
• /
• pp.370-385
• /
• 1990

• Proceedings of the Korean Vacuum Society Conference
• /
• 2008.02a
• /
• pp.347-347
• /
• 2008