• Journal of Environmental Science International
• /
• v.16 no.4
• /
• pp.433-440
• /
• 2007

The photodegradation and by-products of the gaseous toluene with $TiO_2$ (P25) and short-wavelength UV ($UV_{254+185nm}$) radiation were studied. The toluene was decomposed and mineralized efficiently owed to the synergistic effect of photochemical oxidation in the gas phase and photocatalytic oxidation on the $TiO_2$ surface. The toluene by the $UV_{254+185nm}$ photoirradiated $TiO_2$ were mainly mineralized $CO_2$ and CO, but some water-soluble organic intermediates were also formed under severe reaction conditions. The ozone and secondary organic aerosol were produced as undesirable by-products. It was found that wet scrubber was useful as post-treatment to remove water-soluble organic intermediates. Excess ozone could be easily removed by means of a $MnO_2$ ozone-decomposition catalyst. It was also observed that the $MnO_2$ catalyst could decompose organic compounds by using oxygen reactive species formed in process of ozone decomposition.

• Journal of the Korean Ceramic Society
• /
• v.47 no.2
• /
• pp.169-176
• /
• 2010

The Fe-treated CNT/$TiO_2$ photocatalysts mixed with anatase and rutile phase have been developed for the decomposition of non-biodegradable different organic dyes like methylene blue (MB), rhodamine B (Rh.B), and methyl orange (MO) in two conditions as ultraviolet and visible light respectively. The results indicate that all the Fe-CNT/$TiO_2$ composites proved to be more efficient photocatalysts since degradation of MB at higher reaction rates, tthe decomposition rate of different dyes increases with an increase of $Fe^{3+}$ concentration in composites the highest rate of decomposition of different dyes was noted under UV irradiation. These results can indicate that the large CNT network is facilitate the electron transfer and strongly adsorb dye molecules on the texted photocatalysts, iron is reactive in the photo-Fenton process resulting in high production of OH radicals and also high activity of the photocatalyst. And Fe particles can generate more photoinduced electrons to conduction band of $TiO_2$ under visible light irradiation. The composites of Fe-CNT/$TiO_2$ photocatalysts synthesized by a sol-gel method were characterized by BET, TEM, SEM, XRD and EDX.

• Journal of environmental and Sanitary engineering
• /
• v.20 no.4 s.58
• /
• pp.45-50
• /
• 2005

Titania gel formations were prepared by sol-gel method using titanium(IV) chloride $(TiCl_4)$, and its characteristics were analyzed by varying the $epoxide/TiCl_4$ ratio and the amount of water In the end, titania $(TiO_2)$ aerogel were prepared using supercritical drying process. VOCs such as benzene, toluene, and m-xylene (BTX) were oxidized using prepared titania aerogel and commercially available $TiO_2$, and its performance was compared. The surface area, pore volume, and average pore diameter of 1,2-epoxybutane are significantly smaller than the propylene oxide. And the titania aerogels with 6 moi of epoxides have high surface areas, pore volumes, and average pore diameters. As a result of photo-oxidation, conversion of benzene was reached about $70\%$, and other reactants were reached about $60\%$ similarly. The conversion of BTX was increased as inlet concentration decreased. The reactivity of titania calcined at $600^{\circ}C$ was greater than $400^{\circ}C$ and $800^{\circ}C$. Water is required as a reactants for the oxidation of VOCs, and the continuous consumption of hydroxyl radicals required replenishments to maintain catalyst activity. The activity ratio increased with increasing reaction time when enough amount of water was present in the reactor.

• Journal of Powder Materials
• /
• v.24 no.4
• /
• pp.326-331
• /
• 2017

The structural formation of inorganic nanoparticles dispersed in polymer matrices is a key technology for producing advanced nanocomposites with a unique combination of optical, electrical, and mechanical properties. Barium titanate ($BaTiO_3$) nanoparticles are attractive for increasing the refractive index and dielectric constant of polymer nanocomposites. Current synthesis processes for $BaTiO_3$ nanoparticles require expensive precursors or organic solvents, complicated steps, and long reaction times. In this study, we demonstrate a simple and continuous approach for synthesizing $BaTiO_3$ nanoparticles based on a salt-assisted ultrasonic spray pyrolysis method. This process allows the synthesis of $BaTiO_3$ nanoparticles with diameters of 20-50 nm and a highly crystalline tetragonal structure. The optical properties and photocatalytic activities of the nanoparticles show that they are suitable for use as fillers in various nanocomposites.

• Applied Chemistry for Engineering
• /
• v.17 no.5
• /
• pp.561-564
• /
• 2006

$SnO_{2}$-doped anatase type $TiO_{2}$ powder was prepared by the polymerization complex route from tin(IV) bis (acetylacetonate) dichloride, titanium diisopropoxide bis (acetylacetonate) and polyethylene glycol (PEG) as a complexing agent. The structural changes of reaction mixture were monitored by fourier transform infarared (FT-IR) spectroscopy. The microstructure and morphology of gel powder were studied by field-emission scanning electron microscopy (FE-SEM) and X-ray diffractometry (XRD). The photocatalytic activity of these powders with the anatase structure was investigated by using indigo carmine solution.

• Transactions of the Korean hydrogen and new energy society
• /
• v.18 no.1
• /
• pp.40-45
• /
• 2007

Methylene blue(MB) was photocatalytically degraded with one-body photoanode and solar simulator to investigate the possible application to both environmental purification and photoelectrochemical cell for hydrogen production. Photoactive titanium dioxide was formed on both sides of Ti plate following steps such as rinsing-annealing-calcination or anodizing(20 V, 30 V)-annealing($350^{\circ}C$, $450^{\circ}C)$ after etching. The prepared titania plate($2cm{\times}2\;cm$, ca 1.6 mg $TiO_2$ on the basis of $1\;{\mu}m$ thickness) was used to degrade MB(10 ppm in 200 mL solution). The reaction tended to follow the Langmuir-Hinshelwood kinetics with zero order. Comparative experiments with Degussa P25 showed the same zero order kinetics when 2 mg of P25 had been used, while the first order kinetics when 200 mg used. This concludes the feasibility of the prepared titania plate as a material for the purification of low-level harmful organics and an electrode or a membrane for photoelectrochemical system for hydrogen production.

• Journal of the Korean Ceramic Society
• /
• v.45 no.11
• /
• pp.667-674
• /
• 2008

In this study, we prepared Fe-activated carbon fiber(ACF)/$TiO_2$ composites with titanium (VI) n-butoxide (TNB) as the titanium source for ACF pre-treated with iron compounds through the impregnation method. In terms of textural surface properties, the composites demonstrate a slight decrease in the BET surface area of the samples and an increase in the amount of iron compounds treated. The surface morphology of the Fe-ACF/$TiO_2$ composites was characterized by means of SEM. The composites have a porous texture with homogenous compositions of Fe and titanium dioxide distributed on the sample surfaces. The phase formation and structural transition of the iron compounds and titanium dioxide were observed in X-ray diffraction patterns of the Fe-ACF/$TiO_2$ composites. The chemical composition of the Fe-ACF/$TiO_2$ composites, which was investigated with EDX shows strong peaks for the C, O, Fe and Ti elements. The photo degradation results confirm that the Fe-ACF/$TiO_2$ composites show excellent removal activity for the COD in piggery waste due to photocatalysis of the supported $TiO_2$, radical reaction by Fe species, and the adsorptivity and absorptivity of ACF.

• Journal of the Korean Ceramic Society
• /
• v.51 no.4
• /
• pp.307-311
• /
• 2014

ZnS and $ZnS/TiO_2$ were prepared by chemical deposition. The prepared photocatalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX), and transmission electron microscopy (TEM). The generation of reactive oxygen species was detected by monitoring the oxidation reaction from 1,5-diphenyl carbazide (DPCI) to 1,5-diphenyl carbazone (DPCO). Excellent catalytic degradation of methylene blue (MB) solution was observed using the $ZnS/TiO_2$ composites during irradiation with visible light. The results show that the photocatalytic performance of $TiO_2$ nanoparticles is improved by loading with ZnS.

• Journal of Korean Society for Atmospheric Environment
• /
• v.21 no.4
• /
• pp.431-438
• /
• 2005

In order to apply the photocatalytic decomposition of aromatic VOCs, adsorbent prepared from MSWI fly ash was coated by $TiO_2$ solution to endow with photo-catalytic function. The effects of coating number, existence of light source and the type of $TiO_2$ solution used for coating were examined. Adsorbent coated with amorphous $TiO_2$ solution showed higher adsorptivity than adsorbent coated with crystal $TiO_2$ solution. Without light source, breakthrough curve of photo -catalyst absorbent for VOCs removal was similar to that of absorbent made from MSWI fly ash. On the other hand, breakthrough time was enlarged with light source and total removal efficiency of benzene and toluene was also increased. It can be explained as photo-decomposition effect of $TiO_2$ photo-catalyst. Total removal efficiency of benzene and toluene was increased according to the increase of coating number with light source. It was due to the effect of adsorption and photo reaction of photo-catalytic adsorbent. But total removal efficiency of benzene was lower than that of toluene. Because benzene was removed more effectively than toluene by adsorption, but photo - decomposition effect oi toluene was more high than benzene.

• Environmental Engineering Research
• /
• v.24 no.4
• /
• pp.566-571
• /
• 2019

One-pot hydrothermal route was adopted to synthesize Al:BiVO₄, at 4 h and 8 h reaction durations, by adding 1% aluminiumoxide powder (w/v) to the precursors. The products were investigated using several characterization techniques that conform a significant morphological change and a decrease in bandgap energy of the materials upon Al modification of scheelite monoclinic bismuth vanadate matrix at both hydrothermal durations. Antibacterial experiments were performed against methicillin-resistant Staphylococcus aureus in visible light condition to harness the photoxidation property of Al-doped BiVO₄ and compare to that of unaltered BiVO₄. Minimum inhibitory concentration of the synthesized materials was identified. The results indicate that Al-doping on BiVO₄ has a significant effect on its photocatalytic antibacterial performance. Al:BiVO₄ synthesized at 8 h hydrothermal treatment parades excellent sunlight-driven photocatalysis compared to the one synthesized at 4 h.