• 상하수도학회지
• /
• 제18권3호
• /
• pp.392-400
• /
• 2004

This research uses the $TiO_2$/UV process to verify the most suitable condition and possibility to dispose dyeing wastewater that contains pigment and a large amount of pollutants. For this, this research has enforced experiments that compare photo adsorption, photolysis, and photo catalyst oxidation reaction, and also evaluated and analyzed the change of pH and $TiO_2$ dosage, irradiation rates of ultraviolet rays and the dosage change and injection method of $H_2O_2$. According to the results of the dyeing wastewater experiment of storehouse catalyst that uses the new form of $TiO_2$, the photo catalyst oxidation reaction proved to be more effective than photo adsorption and photolysis; 35%, 21% in the case of $TCOD_{cr}$ and 39%, 28% in the case of chromaticity. Taking into consideration the reaction time, amount of photo catalyst reaction and irradiation amount of ultraviolet rays, the decomposition efficiency of pH change proved to be most effective at pH 4. On the whole, the acidity area proved to be effective in dyeing water exclusion than neutral and alkalinity areas. Having evaluated the influence of $TiO_2$ dosage, not only does the decomposition efficiency continuously improve as the $TiO_2$ dosage increases but the shielding effect does not occur also when the $TiO_2$ is at a fixed state. The influence of ultraviolet irradiation amount concluded in the result that as the ultraviolet irradiation amount increases the decomposition efficiency continually increased, but in the case of chromaticity when the irradiation amount was higher than 37.8mW/cm2 the removal efficiency is slowed remarkably. The influence of $H_2O_2$ dosage evaluation reached the results that although the decomposition efficiency increases with the increase of $H_2O_2$ dosage, when above 150mg (total dosage: 1200mg) $H_2O_2$ consumes OH radical itself and reduces the decomposition efficiency. Also in the case of the $H_2O_2$ injection method rather than injecting in the whole amount of $H_2O_2$ (1200mg) needed at the beginning all at once, injecting divided quantities of $H_2O_2$ whenever the electric current density falls below 10mgfl reduces the wases of OH radical due to an excess of $H_2O_2$ and in tum heightens the decomposition efficiency.

• Nuclear Engineering and Technology
• /
• 제51권8호
• /
• pp.1957-1963
• /
• 2019

A UVC photo-Fenton advanced oxidation process (AOP) was studied to develop a process for the decomposition of oxalic acid waste generated in the chemical decontamination of nuclear power plants. The oxalate decomposition behavior was investigated by using a UVC photo-Fenton reactor system with a recirculation tank. The effects of the three operational variables-UVC irradiation, H₂O₂ and Fenton reagent-on the oxalate decomposition behavior were experimentally studied, and the behavior of the decomposition product, CO₂, was observed. UVC irradiation of oxalate resulted in vigorous CO₂ bubbling, and the irradiation dose was thought to be a rate-determining variable. Based on the above results, the oxalate decomposition kinetics were investigated from the viewpoint of radical formation, propagation, and termination reactions. The proposed UVC irradiation density model, expressed by the first-order reaction of oxalate with the same amount of H₂O₂ consumption, satisfactorily predicted the oxalate decomposition behavior, irrespective of the circulate rate in the reactor system within the experimental range.

• 한국식품영양과학회지
• /
• 제33권5호
• /
• pp.785-790
• /
• 2004

배추김치, 갓김치, 부추김치의 용매획분 추출물을 제조한 뒤 항산화관련 물질들의 함량을 측정한 결과 카로테노이드는 갓김치의 hexane층에서, 클로로필 함량은 부추김치의 hexane층에서 가장 높았고, 비타민 C함량은 갓김치의 EtOAc층과 BuOH층에서 가장 높게 나타났다. 총 폐놀화합물은 부추김 치의 CH$_2$Cl$_2$층과 EtOAc층, 배추김치 CH$_2$Cl$_2$층, 갖김치 EtOAc층과 CH$_2$Cl$_2$층에 많이 함유되어 있었다. DPPH법을 이용한 유리기 소거능을 조사한 결과 부추김치 CH$_2$Cl$_2$층과 EtOAc층, 배추김치 CH$_2$Cl$_2$층, 갓김치 EtOAc층에서 효과가 큰 것으로 나타났다. 김치종류별 용매획분을 hairless mouse의 피부균질액에 첨가하여 자외선 B를 조사한 후 지질과산 화물 함량을 측정한 결과 부추김치의 CH$_2$Cl$_2$층과 EtOAc층, 배추김치, 갓김치의 EtOAc층에서 낮게 나타나 항산화성이 높은 획분에서 피부의 광산화 억제효과가 큰 것을 알 수 있었고 김치 용매획분을 크림에 첨가하여 hairless mouse의 등에 직접 도포한 후 자외선 B를 조사하였을 때 대조군에 비해 갓김치의 hexane층, 부추김치의 hexane층과 BuOH층을 제외한 모든 용매획분이 피부홍반의 생성을 억제하였고 특히 갖김치 EtOAc층, 배추김치 CH$_2$Cl$_2$층, 부추김치 물층에서 피부보호효과가 큰 것으로 나타났다.

• 한국염색가공학회지
• /
• 제21권5호
• /
• pp.16-20
• /
• 2009

Films of Poly(ethylene oxide), PEO, were modified to impart hydrophilicity via UV irradiation. The UV irradiation treatment produced new photo-oxidized groups of carbonyl and ether groups as indicated in ATR and ESCA analysis. It was found that water contact angle decreased from $15^{\circ}C$ to $10^{\circ}C$ and total surface energy of PEO increased from 54.2 mN/m to 76.6 mN/m with increasing UV energy, which was attributed to significant contribution of acid base interaction of the photo-oxidized PEO rather than nonpolar interaction originating from the dominant increase in Lewis acid parameter. The increased hydrophilicity and surface energy were also proved by the decreased water wetting time.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.I
• /
• pp.472-475
• /
• 2005

The electrical performances of liquid crystal (LC) cells with chloromethylated polyimide (CMPI) alignment layers were investigated. The CMPI layer was previously reported as a multifunctional layer that does role of LC alignment and planarization layer as well as photo-alignment material with high photosensitivity and excellent thermal stability. The capacitance-voltage (C-V) characteristics of LC cells with CMPI alignment layers were measured. Mechanical rubbing of the CMPI layer did not generate much difference in residual DC when compared to commercial PI. However, the LC cell with photo-oxidation CMPI layer shows a high residual DC value and a corresponding low voltage holding ratio (VHR) due to the photo-induced ionic charges on the alignment layer.

• 상하수도학회지
• /
• 제24권1호
• /
• pp.109-117
• /
• 2010

In the present study, the degradation characteristics of Lindane by Advanced Oxidation Processes(UV/$H_2O_2$, Photo-Fenton process) were studied. The degradation efficiency of Lindane in aqueous solution was investigated at various initial pH values, Fenton's reagent concentrations and initial concentrations of Lindane. GC-ECD was used to analyze lindane. Lindane has not been degraded without application of AOPs over two hours. But, approximately 5% of lindane was degraded with UV or $H_2O_2$ alone. Lindane with UV/$H_2O_2$ process showed approximately 7% higher removal efficiency than $H_2O_2$ process. In the UV/$H_2O_2$ process, the pH values did not affect the removal efficiency. The optimal mole ratio of $H_2O_2/Fe^{2+}$ for lindane degradation is about 1.0 in Photo-Fenton process. Also, the experimental results showed that lindane removal efficiency increased with the decrease of initial concentration of lindane. Under the same conditions, the order lindane of removal efficiency is as following : Photo-Fenton process > UV/$H_2O_2$ process > $H_2O_2$ process. In addition, intermediate products were identified by GC-MS techniques. Than PCCH(Pentachlorocyclohexene) was identified as a reaction intermediate of the Photo-Fenton process.

• 한국재료학회지
• /
• 제19권9호
• /
• pp.481-487
• /
• 2009

The photocatalysts of Fe-ACF/$TiO_2$ compositeswere prepared by the sol-gel method and characterized by BET, XRD, SEM, and EDX. It showed that the BET surface area was related to adsorption capacity for each composite. The SEM results showed that ferric compound and titanium dioxide were distributed on the surfaces of ACF. The XRD results showed that Fe-ACF/$TiO_2$ composite only contained an anatase structure with a Fe mediated compound. EDX results showed the presence of C, O, and Ti with Fe peaks in Fe-ACF/$TiO_2$ composites. From the photocataytic degradation effect, $TiO_2$ on activated carbon fiber surface modified with Fe (Fe-ACF/$TiO_2$) could work in the photo-Fenton process. It was revealed that the photo-Fenton reaction gives considerable photocatalytic ability for the decomposition of methylene blue (MB) compared to non-treated ACF/$TiO_2$, and the photo-Fenton reaction was improved by the addition of $H_2O_2$. It was proved that the decomposition of MB under UV (365 nm) irradiation in the presence of $H_2O_2$ predominantly accelerated the oxidation of $Fe^{2+}$ to $Fe^{3+}$ and produced a high concentration of OH radicals.

• 한국결정성장학회지
• /
• 제8권1호
• /
• pp.117-123
• /
• 1998

초크랄스키 실리콘 기판의 뒷면에 형성된 기계적 손상이 미치는 효과에 대하여 고찰하였다. 기계적 손상의 정도는 레이저 여기/극초단파 반사 광전도 감쇠법에 의한 소수반송자 재결합 수명, 광열범위, X-선 단면 측정 및 습식산화/선택적 식각 방법으로 평가하였다. 그 결과, 웨이퍼 뒷면에 가해지는 기계적 손상의 세기가 강할수록 소수반송자 재결합 수명은 짧아지고, 광열 변위의 평균값은 비례적으로 증가하였으며, 손상된 웨이퍼에서 Grade 1의 과잉 광열 변위값을 1로 봤을 때 과잉 광열 변위의 정규화한 상대 정량 비는 Grade 1: Grade 2:Grade 3 = 1:19.6:41이다.

• 한국포장학회지
• /
• 제24권3호
• /
• pp.141-148
• /
• 2018

Photo-oxidation is one of the main causes of food deterioration of great variety of foods, such as dairy products, nuts, meat products, and wine. It causes a loss of both nutritional value and sensorial quality of products and may even leads to the formation of toxic compounds. Active packaging for food and beverages has been investigated and developed with embedding light absorbers or blocking materials into the plastics. In recent years, several novel light barrier materials have been proposed as an alternative option for different applications. This article reviews the up-to-date technology in light absorber and blocking material with special emphasis on chemical compound and mechanism. Inorganic, organic, hybrid organic-inorganic, and natural light absorbers were scoped. The challenges and future perspectives of light barrier materials are also discussed.

• 대한환경공학회지
• /
• 제30권6호
• /
• pp.642-652
• /
• 2008

본 연구는 축산폐수 중 COD$_{Cr}$을 응집공정 후 Photo-Fenton 공정에 의해 산화분해 최적조건 및 제거 예측식에 수립에 관한 연구이다. 본 연구는 축산폐수 중 COD$_{Cr}$에 대한 Photo-Fenton 산화반응을 이용하여 이들 분해특성을 2차원 반응모델로 추정하기 위해 중심합설계법 대안으로 많이 사용되고 있는 박스-벤켄법(Box-Behnken method)을 이용하였다. 최적조건 수립을 위한 입력변수, 즉 3가지 변수(Fe(II)(x$_1$), $H_2O_2(x_2)$, pH(x$_3$)) 등을 램덤화, 반복화 및 블록화 원리에 따라 실험설계하여 반응값에 대한 예측식을 수학적으로 산출하였다. 수학적 및 통계적으로 산출된 예측식은 Y = 79.3 + 15.61x$_1$ - 7.31x$_2$ - 4.26x$_3$ - 18x$_1{^2}$ - 10x$_2{^2}$ - 11.9x$_3{^2}$ + 2.49x$_1x_2$ - 4.4x$_2x_3$ - 1.65x$_1x_3$와 같이 얻을 수 있었고 COD$^{Cr}$ 제거율(%)의 실측치에 대한 예측치의 적합도(goodness of fit) 검증시 결정계수(coefficient of determination: R$^2$) 0.96으로 에측식을 충분히 설명할 수 있었다. 예측 모형에 대한 최소제곱추정법으로 적합된 반응표면에서 1차 선형항(linear term)은 Fe(II)(x$_1$), $H_2O_2(x_2)$, 그리고 pH(x$_3$)은 상승작용(synergistic effect)으로 반응모델에 유의한 차이를 보였으며(p < 0.001) 그러나 교호항(cross-product term)은 $H_2O_2$ $\times$ pH(x$_2x_3$)와 순수이차항(quadratic terms)의 Fe(II) $\times$ Fe(II)(x$_1{^2}$), $H_2O_2$ $\times$ H$_2O_2$(x$_2{^2}$) 그리고 pH $times$ pH(x$_3{^2}$) 등은 대립적인(감쇠)(antagonistic effect) 작용으로 반응모델에 유의한 차이를 보였다(p < 0.01). 반응 모델에 대한 예측식 수립 후 COD$_{Cr}$ 제거율(%)의 최적조건을 도출하기 위해 정준분석(canonical analysis)와 능선분석(ridge analysis)에 이용한 결과 반응값(결과값: Y)은 84 $\pm$ 0.95%, COD$_{Cr}$ 최적처리를 위한 변수들의 조건은 Fe(II)(X$_1$) = 0.0146 mM, $H_2O_2$(X$_2$) = 0.0867 mM 그리고 pH(X$_3$) = 4.704 등의 결과를 얻을 수 있었다. 또한 이들 최적조건을 이용하여 재현성을 통한 모델검증 결과 높은 신뢰성을 보였다.