• Journal of IKEEE
• /
• v.21 no.2
• /
• pp.146-149
• /
• 2017

In this paper, we propose a wide-range radiation measurement system using GM Tube and NaI(TI) detector. The proposed system is designed as a small module optimized to control and count the detector signal of NaI(Tl) Detector and GM Tube. The radiation dose is measured in a wide-range 0.1uSv/h to 10mSv/h in conjunction with two detectors, and two detectors operate simultaneously at 10uSv/h to 100uSv/h, where the measurement interval overlaps. The radiation dose was selected using a wide-range radiation measurement algorithm that controls the on/off function of the detector in the appropriate interval for the overlapped radiation measurable interval. In order to evaluate the performance of the proposed system, it has been confirmed that the measurement uncertainty of each section is measured as ${\pm}7.5%$ and it operates normally under ${\pm}15%$ of the international standard.

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.2
• /
• pp.209.2-209.2
• /
• 2012

UFFO Burst Alert & Trigger telescope (UBAT) is one of major instruments of UFFO-Pathfinder. The UBAT aims at 10 arcmin resolution localization of Gamma Ray Bursts with X-ray coded mask technique. It has $400mm{\times}400mm$ coded mask aperture, hopper, shielding and detector module with effective area of $191cm^2$. The detector module consists of an assembly of 36 64-ch MAPMTs and $25mm{\times}25mm$ pixellated YSO crystal array, and associated analog and digital electronics of about 2500 channels. We performed a vibration test using a dummy MAPMT with the detector module structure to measure the indused stress applied onto the MAPMT. We designed a sub-structure on the detector module to avoid the resonance that would otherwise deforms the detector module structure. A finite element analysis confirms the reduction of the load acceleration down to 12g. The experimental results are to be reported. Consequently, it proves that the MAPMT arrays of the flight UBAT detector module structure would survive in the space launch environment.

• Journal of the Korean Society of Radiology
• /
• v.13 no.6
• /
• pp.841-846
• /
• 2019

Effect of misalignment on the performance was evaluated for the development of time-of-flight(TOF)-PET detector. A pair of TOF-PET detector consists of Lutetium-yttrium oxyorthosilicate(LYSO) scintillation crystal with a volume of 3 mm × 3 mm × 20 mm and Geiger-mode avalanche photodiodes(GAPD) photo-sensor with a active area of 3.07 mm × 3.07 mm. Analog output signals from TOF-PET detector were sent to the pre-amplifier and then fed into the gain adjust circuit for achievement of gain homogeneity for each detector. The amplified signals were recorded and digitized by data acquisition system based on oscilloscope. The effect of the detector misalignment between LYSO and GAPD was examined for four different alignment offsets of 0.0 mm, 0.5 mm, 1.0 mm and 1.5 mm for a pair of TOF-PET detector. The photopeak position decreased from ~400 mV to ~250 mV with increasing detector misalignment. the energy resolution and time resolution were degraded from 11.6% to 16.2%, and from 477 ps to 632 ps, respectively. This study demonstrated that PET detector performance was degraded considerably depending on the detector misalignment, which would be a critical issue for the development of TOF-PET detector.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.272-272
• /
• 2012

Additional neutral particle analyzer has been installed to investigate the variation of fast ion tails with regard to the line of sight during 2012 KSTAR campaign. The system has the same photo-diode particle detector as previous system [1]. Both newly installed system and previous system modifield for 2012 campaign have two channels. One has a particle stopper transparent to hard X-ray, the other has no one. It will be used to separate the hard X-ray component from total hard X-ray and fast neutral counts. It is expected to measure fast ion tails more clearly through this extended system. A detailed system and calibration result will be presented in the conference.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.77-77
• /
• 2003

산업화에 따라 각종 산업분야에서 유기 용제의 사용이 증가하게 되었고 대기오염, 수질오염 등의 상태가 심각해져가고 있는 실정이다 그러나 다양해진 오염물질을 처리하는 데 있어서 기존의 산화처리방법은 한계에 달하였고 새로운 처리공정으로 최근 고급산화법(AOP : Advanced Oxidation Process)에 대한 연구가 활발하게 진행되고 있다. 이에 본 연구에서는 대기환경 및 인체에 심각한 영향을 주는 VOCs(Voletail Organic compounds)중 BTEX(Benzene, Toluene, Ethylbenzene, Xylene)를 다양한 형태의 광촉매제를 이용하여 기상 광분해한 후 이에 대한 최적의 분해 조건과 분해율을 비교하고자 하였다. 순환식의 자체 제작한 기상광반응장치를 이용하여, CVD법으로 TiO$_2$ 입자를 알루미나 비드위에 코팅한 볼과 같은 방법으로 유리기판위에 코팅한 판상의 광촉매제 그리고 결정성이 각기 다른 루틸상과 아나타제 그리고 아나타제/루틸 혼합상의 TiO$_2$ 분말을 직접 이용하여 VOCs 농도와 종류, 광원의 종류 및 세기를 변화시켜 PID(Photo ionization Detector)방식의 순환식 VOCs 측정기를 이용하여 광분해율을 실시간으로 측정하였다.

• Journal of Sensor Science and Technology
• /
• v.20 no.1
• /
• pp.53-57
• /
• 2011

We developed a small methane detection system because methane gas is used in many areas and is dangerous. The developed system consisted of LD(Laser Diode) tuned a wavelength of $1.65\;{\mu}m$, two mirrors to collect a laser beam, photo detector. It could detect methane gas at a long range and its sensitivity was 1.98 V/$CH_4%$.

• Korean Journal of Optics and Photonics
• /
• v.14 no.2
• /
• pp.161-165
• /
• 2003

Optical 60 ㎓ millimeter-wave (MMW) signal generation is demonstrated using the sideband injection-locking method in the master/slave configuration, where two slave lasers are locked to two among several side-bands produced by the direct rf-modulation of a master laser. These two locked slave laser outputs beat against each other in the photo-detector and produce stable and very pure 60 ㎓ signals.

• Proceedings of the KIEE Conference
• /
• 1994.11a
• /
• pp.382-384
• /
• 1994

Wireless communication has become a hot issue for its simplicity. Using light wave instead of micro wave has many advantages. It is simple to design a circuit because we can make a circuit with discrete components such as photo diode, photo detector, OP Amp[2]. And we can have many communication channels for we can use every frequency domain. In this paper, we design the wireless communication system and analyze the pulse signal. Then using ray tracing technology we simulate the distribution of light beam.

• Journal of Sensor Science and Technology
• /
• v.17 no.6
• /
• pp.447-453
• /
• 2008

Respiration rate is one of the important vital signs. Photo-plethysmography (PPG) measurement especially on a finger has been widely used in pulse oximetry and also used in estimating respiration rate. It is well known that PPG contains respiration-induced intensity variation (RIIV) signal. However, the accuracy of finger PPG method has been controversial. We introduced a new technique of enhancing motion artifact by respiration. This was achieved simply by measuring PPG on the thorax. We examined the accuracy of these two PPG methods by comparing with two existing methods based on thoracic volume and nostril temperature changes. PPG sensing on finger tip, which is the most common site of measurement, produced 6.1 % error. On the other hand, our method of PPG sensing on the thorax achieved 0.4 % error which was a significant improvement. Finger PPG is sensitive to motion artifact and it is difficult to recover fully small respiratory signal buried in waveform dominated by absorption due to blood volume changes. Thorax PPG is poor to represent blood volumes changes since it contains substantial motion artifact due to respiration. Ironically, this inferior quality ensures higher accuracy in terms of respiration measurement. Extreme low-cost and small-sized LED/silicon detector and non-constrained reflection measurement provide a great candidate for respiration estimation in ubiquitous or personal health monitoring.

• Journal of Welding and Joining
• /
• v.20 no.1
• /
• pp.62-68
• /
• 2002

This study investigated the feasibility of penetration depth measurement using infrared temperature sensing on the weld surface. The detection point was optimized by FEM analysis in the laser keyhole welding. The profile of the weld surface temperature was measured using infrared detector array. Surface temperature behind the weld pool is proportional or exponentially proportional to penetration depth and bead width. From the results, the monitoring device of surface temperature using infrared detector array was applicable fur real time penetration depth control.