• 한국세라믹학회지
• /
• 제30권2호
• /
• pp.148-156
• /
• 1993

TiN films were deposited onto high speed steel (SKH9) by plasma assisted chemical vapor deposition (PACVD) using a TiCl4/N2/H2/Ar gas mixture at around 50$0^{\circ}C$. The effects of the deposition temperature, R.F. power and TiCl4 concentration on the deposition of TiN and the microhardness of TiN film were investigated. The crystallinity and the microhardness of TiN films were improved with increase of the deposition temperature. Optimum deposition temperature in this study was 50$0^{\circ}C$, because a softening or phase transformation of the substrate occurred over 50$0^{\circ}C$. A large increase of the film growth rate with a strong(200) preferred orientation was obtained by increasing R.F. power. Much chlorine content of about 10at.% was found in the deposited films and resulted in relatively low average microhardness of about 1, 500Kgf/$\textrm{mm}^2$ compared with the theoretical value(~2, 000Kgf/$\textrm{mm}^2$).

• 한국주조공학회지
• /
• 제9권6호
• /
• pp.463-473
• /
• 1989

This study is aimed to investigate the effect of cyclic heat treatment which is special heat treatment on the strength and toughness in Multi-phase(Ferrite-Bainite-Martensite) Ductile cast Irons. Spceimens were austenitized at eutectoid transformation temperature range(${\alpha}+{\gamma}$) for 30min and austempered at $300^{\circ}C$ and $400^{\circ}C$ for different holding times, and then quenched in ice water to obtain the multi-phase(Ferrite-Bainite-Martensite) structure from various prior structures, which was obtained by various cyclic heat treatments. As the number of cycle in cyclic heat treatment increased, volume fraction of pearlite increased and the its morphology was refined. As the number of cycle in cyclic heat treatment increased, the multi-phase(Ferrite-Bainite-Martensite) was dispersed in whole matrix as refined island phase. Particularly, martensite among the multi-phase gradually became a spherical shape. Good combination in impact energy and tensile strength was detained in $840^{\circ}C-300^{\circ}C-15min$ condition after 10 cycles in cyclic heat treatment, and its multi-phase volume fraction is Ferrite(50%)-Martensite(l3%)-Bainite(37%).

• 한국재료학회지
• /
• 제13권3호
• /
• pp.137-143
• /
• 2003

The air gap between the metal and mold, formed by shrinkage during solidification, causes surface and subsurface cracks in the continuous casting process. Molten crack on the surface might also occur due to improper heat transfer between them. In order to compensate the air gap in mold design, the thermal contraction is an essential factor. In this study, the thermal contraction and expansion behaviors were examined from the ($\alpha$ and pearlite)/${\gamma}$ to ${\gamma}$/$\delta$ transformations in continuous casting steels by the commercial dilatometer and the self- assembled dilatometer with laser distance measurement. It was found that the thermal contraction and expansion behaviors were very dependant on the phase transformation of the ${\gamma}$/$\delta$ as well as ($\alpha$ and pearlite)/${\gamma}$. The sudden volume change from $\delta$ to ${\gamma}$ which might cause cracks in the continuous casting process, was observed on cooling just below the melting temperature by the self-assembled dilatometer.

• 한국재료학회지
• /
• 제4권4호
• /
• pp.472-476
• /
• 1994

질산납으로부터 침전법으로 제조된 PbO-전구체의 상변태를 열분석, X-선 회절, 적외선 흡수 및 Raman분광 분석 등을 통하여 조사하였다. 질산납 수용액으로부터 $45^{\circ}C$, pH 9.0의 반응조건에서 PhO-전구체를 제조하였다. 침전물은 hydrous lead oxynitrate와 lead hydroxynitrate의 혼합체이었다. $560^{\circ}C$까지 열처리온도가 증가함에 따라 전구체는 $3Pb(NO_{3})_{2}$ㆍ7PbO를 거쳐 $Pb(NO_{3})_{2}$ㆍ5PbO로 된 후에 PbO(litharge)로 변화되었으며, $560^{\circ}C$이상에서 최종적으로 massicot형의 PbO로 변태되었다.

• 대한화학회지
• /
• 제63권2호
• /
• pp.94-101
• /
• 2019

Nb, Mo-doped and Nb/Mo-codoped $VO_2(M)$ nanocrystallites with various doping levels were synthesized for the first time by a hydrothermal and post thermal transformation method. The reversible phase transition characteristics of those doped $VO_2(M)$ was comparatively investigated. Nb-doping of $VO_2(M)$ by this method resulted in a very efficient lowering of the transition temperature ($T_c$) with a rate of $-16.7^{\circ}C/at.%$ that is comparable to W-doping, while Mo-doping did not give a serious reduction of $T_c$ with only a rate of $-5.1^{\circ}C/at.%$. Nb/Mo-codoping gave a similar result to Nb-doping without a noticeable difference. The thin films of Nb-doped and Nb/Mo-codoped $VO_2(M)$ with a thickness of ca. 120 nm were prepared by a wet-coating of the nanoparticle-dispersed solutions. Those films showed a good thermochromic modulation of near infrared radiation with 30-35% for Nb-doped $VO_2(M)$ and 37-40% for Nb/Mo-codoped ones. Nb/Mo-codoped $VO_2(M)$ film showed slightly enhanced thermochromic performance compared with Nb-doped $VO_2(M)$ film.

• 한국결정성장학회지
• /
• 제8권4호
• /
• pp.634-639
• /
• 1998

$Y_2O_3$와 $Nb_2O_5$가 첨가된 지르코니아에 입자 크기가 다른 두종류의 Al2O3를 부피비로 10~30% 첨가한 복합체를 155$0^{\circ}C$ 온도에서 5시간 소결하여 $250^{\circ}C$ 온도의 공기 분위기하에서 1000시간 혹은 $180^{\circ}C$ 온도의 0.3MPa H2O vapor pressure 분위기하에서 5시간 열처리를 하여 X-ray 회절분석 방법을 이용하여 저온 상안정성을 조사하였다. 복합체 전부 열처리 후에 정방정 상에서 단사정 상으로 상전이가 발생하지 않는 우수한 저온 상안정성이 관찰되었다. 복합체의 상아정성에 Nb 첨가가 $Al_2O_3$의 첨가보다 더 효과적이었다. 2.8$\mu$m 입자크기를 가진 Al2O3를 부피비로 20% 첨가한 복합체에서 최적의 조건이 관찰되었으며 강도와 인성값은 각각 670MPa와 7.1MPam1/2이었다. Al2O3 입자 크기가 2.8$\mu$m에서 0.2$\mu$m로 감소함에 따라 강도는 다소 증가하였으나 파괴인성값은 감소하였다.

• Smart Structures and Systems
• /
• 제15권6호
• /
• pp.1521-1542
• /
• 2015

The use of shape memory alloys (SMAs) in dynamical systems has an increasing importance in engineering especially due to their capacity to provide vibration reductions. In this regard, experimental tests are essential in order to show all potentialities of this kind of systems. In this work, SMA springs are incorporated in a dynamical system that consists of a one degree of freedom oscillator connected to a linear spring and a mass, which is also connected to the SMA spring. Two types of springs are investigated defining two distinct systems: a pseudoelastic and a shape memory system. The characterisation of the springs is evaluated by considering differential calorimetry scanning tests and also force-displacement tests at different temperatures. Free and forced vibration experiments are made in order to investigate the dynamical behaviour of the systems. For both systems, it is observed the capability of changing the equilibrium position due to phase transformations leading to hysteretic behaviour, or due to temperature changes which also induce phase transformations and therefore, change in stiffness. Both situations are investigated by promoting temperature changes and also pre-tension of the springs. This article shows several experimental tests that allow one to obtain a general comprehension of the dynamical behaviour of SMA systems. Results show the general thermo-mechanical behaviour of SMA dynamical systems and the obtained conclusions can be applied in distinct situations as in rotor-bearing systems.

• 한국세라믹학회지
• /
• 제35권1호
• /
• pp.88-96
• /
• 1998

The structural and electrical properties of titanium dioxide(TiO2) thin films deposited on p-type (100) si and 4$^{\circ}$off(100) Si substartes by metalorganic chemical vapor deposition (MOCVD) have been studied with post rapid thermal annealing. TiO2 thin films of anatase phase were grown at 300-500$^{\circ}C$ using titanium post rapid thermal annealing at a temperature of 800$^{\circ}C$ for 30sec. rutile phase was observed in the condition of the deposition temperature over 350$^{\circ}C$ in the ambient air atmosphere and at 500$^{\circ}C$ in cacuu,. SEM and AFM study show-ed surface roughness were increased slightly from 40${\AA}$to 55${\AA}$ after annealing due to grain growth and phase transformation. From capacitane-voltage measurement of Al/TiO2./p-Si structure after annealing we obtained ideal capacitance-voltage characteristics of MOS structure with dielectric constant of 16-22 in case of (100) Si and about 30- in case of 4$^{\circ}$off(100) Si but showed the higher leakage current.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2003년도 somma/kms meeting
• /
• pp.186-186
• /
• 2003

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 춘계학술발표대회 논문집
• /
• pp.151-154
• /
• 2001

Shape memory alloy (SMA) has demonstrated its potentials for various smart structure applications. SMA wires undergo a reversible phase transformation from martensite to austenite as temperature increases. This transformation leads to shape recovery and associated recovery strains. If SMA actuators are embedded off the neutral surface and are oriented in arbitrary angles with respect to a beam axis, then the beam bends and twists due to the coupling effects of recovery strains activated. In this study, the bending and twisting of a SMA/Composite beam were controlled by both electric resistive heating and passive elastic tailoring. 3-dimensional finite element formulations were derived and validated to analyze the responses of the SMA/Composite beam. Numerical results show that the shape of the SMA/Composite beam can be controlled by judicious choices of control temperatures, SMA angles, and elastic tailoring.