• Journal of Power System Engineering
• /
• v.22 no.1
• /
• pp.48-55
• /
• 2018

It has recently been reported that methanol fuel has been used in the product carrier with established duel fuel engine, which has been greatly reducing emissions of $CO_2$, NOx and SOx from the engine. However, to use methanol alone as fuel oil in a general diesel engine, design modification of cylinder head is needed because the ignition aid device or the duel fuel injection system is needed. On the other hand, only if the mixer is installed on the fuel oil supply line, diesel oil - methanol blending oil can be used as fuel oil for the diesel engine, but there is a problem of the phase separation when two fuels are mixed. In this study, diesel oil and methanol were blended compulsorily in preventing the phase separation with installing agitators and a fuel oil boost pump on fuel line of a test engine. Also, cylinder pressure and fuel consumption quantity were measured according to engine load and methanol blending ratio, and indicated mean effective pressure, heat release rate and combustion temperature obtained from the single zone combustion model were analyzed to investigate the effects of latent heat of vaporization of methanol on combustion stability and characteristics. As a result, the combustion stability and characteristics of 10% methanol blending oil are closest to the those of diesel oil, and it could be used as fuel oil in existing diesel engines without deterioration of engine performance and combustion characteristics.

• Elastomers and Composites
• /
• v.36 no.3
• /
• pp.188-194
• /
• 2001

Thermoplastic elastomers based on dynamically vulcanized NR/TOR/PP (rubber/PP=70/30) blends were prepared in a Haake banbury mixer. Effect of TOR content on the mechanical, dynamic mechanical and thermal stability of the rubber/plastic blends was characterized by UTM, DMTA, and TGA. On the addition of trans-polyoctylene rubber(TOR) to the rubber phase, there was a decrease in compression set and increase in tensile properties, hardness and dynamic properties as well as thermal stability or the elastomeric blends. Improvements in the properties were believed to be due to an increase in crosslink density of the rubber phase and increase in homogeneity of the blends.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.5
• /
• pp.1038-1044
• /
• 2011

In this paper, the multichannel intermediate frequency transceiver for broadband multimedia system is designed and the experimental results are analyzed. Basic elements of the transceiver such as frequency synthesizer, amplifier, mixer, automatic gain control amplifier are introduced. The analysis technique described here applies not only to amplifier but also to any other nonlinear components such as mixers and frequency doubler. Through the investigation of the power spectrum density of the transmitted signal, the phase noise of the local oscillator is evaluated below 70 dBc/kHz. The frequency characteristics of the modulated signal is flat within the system bandwidth. Also the effects of adjacent channel interference and supurious emission are analyzed. And the function of automatic gain control amplifier is well operated.

• Journal of Powder Materials
• /
• v.31 no.1
• /
• pp.43-49
• /
• 2024

In this study, a core-shell powder and sintered specimens using a mechanically alloyed (MAed) Ti-Mo powder fabricated through high-energy ball-milling are prepared. Analysis of sintering, microstructure, and mechanical properties confirms the applicability of the powder as a sputtering target material. To optimize the MAed Ti-Mo powder milling process, phase and elemental analyses of the powders are performed according to milling time. The results reveal that 20 h of milling time is the most suitable for the manufacturing process. Subsequently, the MAed Ti-Mo powder and MoO₃ powder are milled using a 3-D mixer and heat-treated for hydrogen reduction to manufacture the core-shell powder. The reduced core-shell powder is transformed to sintered specimens through molding and sintering at 1300 and 1400℃. The sintering properties are analyzed through X-ray diffraction and scanning electron microscopy for phase and porosity analyses. Moreover, the microstructure of the powder is investigated through optical microscopy and electron probe microstructure analysis. The Ti-Mo core-shell sintered specimen is found to possess high density, uniform microstructure, and excellent hardness properties. These results indicate that the Ti-Mo core-shell sintered specimen has excellent sintering properties and is suitable as a sputtering target material.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.8
• /
• pp.117-124
• /
• 2009

This paper describes a 3 to 5 GHz frequency synthesizer for MB-OFDM (Multi-Band OFDM) UWB (Ultra- Wideband) application using 0.13 ${\mu}m$ CMOS process. The frequency synthesizer operates in the band group 1 whose center frequencies are 3432 MHz 3960 MHz, and 4488 MHz. To cover the overall frequencies of group 1, an efficient frequency planning minimizing a number of blocks and the power consumption are proposed. And, a high-frequency VCO and LO Mixer architecture are also presented in this paper. A new mixed coarse tuning scheme that utilizes the MIM capacitance, the varactor arrays, and the DAC is proposed to expand the VCO tuning range. The frequency synthesizer can also provide the clock for the ADC in baseband modem. So, the PLL for the ADC in the baseband modem can be removed with this frequency synthesizer. The single PLL and two SSB-mixers consume 60 mW from a 1.2 sV supply. The VCO tuning range is 1.2 GHz. The simulated phase noise of the VCO is -112 dBc/Hz at 1 MHz offset. The die area is 2 ${\times}$ 2mm$^2$.

• Korean Journal of Applied Biomechanics
• /
• v.14 no.3
• /
• pp.17-35
• /
• 2004

The purpose of this study is to explain developmental process of gait via angle-angle diagram to understand how coordinated relationships and control change with age. Twenty four female children, from one to five years of age were the test subjects for this study, and their results were compared to a control group consisting of twenty one adult females. The Vicon 370 CCD camera, VCR, video timer, monitor, and audio visual mixer was utilized to graph the gait cycle for all test subjects. Both coordinated Intra-limb relationships, and range of motion and timing according to quadrant were explained through the angle angle diagram. Movement in the sagittal plane showed both coordinated relationships and control earlier than movement in the coronal or transverse plane. In the sagittal plane, hip and Knee coordinated relationships developed first (from one year of age.) Coordinated relationships in the Knee and ankle and hip and ankle developed next, respectively. Both hip and ankle and knee and ankle development were inhibited by the inability of children to completely perform plantar flexion during the swing and initial double limb support phases. Children appeared to compensate for this by extending at their hip joint more than adults during the third phase, final double limb support. In many cases the angle angle diagram for children had a similar shape as adult's angle angle diagram. This shows that children can coordinate their movements at an early age. However, the magnitudes and timing of children's angle angle diagrams still varied greatly from adults, even at five years of age. This indicates that even at this age, children still do not possess full control of their movements.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.12
• /
• pp.1097-1106
• /
• 2011

In this paper, we present design method of wideband single-sideband mixer(SSM) with excellent sideband suppression and carrier suppression. We proposed SSM with 4-band split structure for uniform output flatness. From circuit simulation of this structure using Microwave OfficeTM, we got satisfactory results. We realized a SSM based on this results, then we experimented. The measured results show excellent agreements with the simulated results. We compared with two SSM's(target SSM(M Co. SM0218LC1CDC SSM) and our SSM) as well. The presented SSM is 3.35 times bigger, but sideband suppression is 3 dBc better and carrier suppression is 8 dBc better than those of comparative SSM, respectively.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.27 no.2
• /
• pp.70-74
• /
• 2017

Two milling methods, dry vibration milling and wet ball milling, were used to prepare $Na_{2/3}(Ni_{1/3}Mn_{2/3})O_2$ powders as a cathode material for sodium ion batteries. The morphology and electrochemical property of the two powders with different milling processes were compared to each other. The particle size is less than $1{\mu}m$ in the dry vibration milled powder, while lots of larger particles than $1{\mu}m$ were found in the wet ball milled one. The single phase of $Na_{2/3}(Ni_{1/3}Mn_{2/3})O_2$ was obtained in the temperature range of $875{\sim}900^{\circ}C$. The discharge capacity and discharge voltage of the powder prepared by the dry process were higher than those of one prepared by the wet process.

• Aerospace Engineering and Technology
• /
• v.6 no.1
• /
• pp.83-91
• /
• 2007

An experimental verification of multipactor(MP) discharge for S-band diplexer as a sample DUT for space application by an in-house MP test facility is proposed. The designed diplexer having two BPFs for Rx and Tx is applied to a design of five pole inter-digital cavity type band pass filter with chebyshev response, it has 2.7 % bandwidth centered at 2.232 and 2.055 GHz for Rx, Tx, respectively. To avoid the MP discharge, the accurate design and analysis methods based on 3D EM field analysis are considered. The proposed in-house MP test facility consists of a phase detecting system using a doubly balanced mixer as a simple, low cost and real time MP test method compared with results of previously well-known MP detection systems as cross reference methods. The calculated MP threshold RF input power is 43.13 dBm. The measured one is 43 dBm and 44 dBm for CW, pulsed mode test, respectively.

• Polymer(Korea)
• /
• v.26 no.3
• /
• pp.316-325
• /
• 2002

The deformation and coalescence behaviors of immiscible LDPE/PS blends (86.5/13.5 vol%) prepared by internal mixer were studied using rheometer and scanning electron microscope. The fine droplets coagulated at initial stage of mixing, and deformed fiber at large strain. The critical capillary number was calculated according to the empirical equation of De Bruijn and it was 0.95, the local capillary number was 3.867. The polymer blends were annealed at $200^{\circ}C$ for various time to investigate morphological change of polymer blends. The maximum size of droplet after annealing at $200^{\circ}C$ was found at ${\gamma}$=1798, and there was destruction of the morphology at 15 minutes of annealing time. The viscosity of matrix was critical to determine a coalescence of droplet.