• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.11
• /
• pp.1379-1386
• /
• 2013

The present work reports the mismatch limit loads for a V-groove welded pipe for a circumferential crack using finite element (FE) analyses. To integrate the effect of groove angles on mismatch limit loads, one geometry-related slenderness parameter was modified by relevant geometric parameters including the groove angle, crack depth, and root opening based on plastic deformation patterns in the theory of plasticity. Circumferential through-wall cracks are located at the centre of the weldments with two different groove angles ($45^{\circ}$, $90^{\circ}$). With regard to the loading conditions, axial (longitudinal) tension and bending are applied for all cases. For the parent and weld metal, elastic-perfectly plastic materials are considered to simulate and analyze under- and over-matching conditions in plasticity. The overall results from the proposed solutions are found to be similar to the FE results.

• YAKHAK HOEJI
• /
• v.41 no.1
• /
• pp.38-47
• /
• 1997

Using a concentric cylinder type, rheometer. the steady shear flow properties of vaseline were measured over the temperature range of 20~70${\circ}$C. In this paper, the shea rate and temperature dependencies of its flow behavior were investigated and the validity of some flow models was examined. In addition, the flow characteristics over a wide temperature range were quantitatively evaluated by calculating the various material parameters. Main findings obtained from this study can be summarized as follows: (1) At relatively lower temperature range, vaseline is a plastic fluid with a yield stress and its flow behavior shows shear-thinning characteristics. (2) As the temperature increases, the value of a yield stress and the degree of shear-thinning become smaller, consequently, the Newtonian flow behavior occurs at a lower shear rate range. (3) At temperature range lower than 45${\circ}$C, the flow behavior shows much stronger temperature dependence, and a larger activation energy is needed for flow. (4) The Herschel-Bulkley model is the most effective one g$^3$ to predict the flow behavior of vaseline having a yield stress. The validity of the Bingham and Casson models becomes more available with increasing temperature. The flow behavior of vaseline at temperature range higher than 45${\circ}$C can be perfectly described by the Newton model.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.8 no.4
• /
• pp.11-20
• /
• 2004

This paper suggests the site-dependent ductility factor which is a key component of response modification factor(R). To compute the ductility factor, a group of 1,860 ground motions recorded from 47 earthquake was considered. Based on the local site conditions at the recording station, ground motions were classified into four groups according to average shear wave velocity. This site classification was consistent with site categories of the UBC(1997), NEHRP(1997) and IBC 2000(1997). Based on the results of regression analysis, a simplified equations were proposed to compute site-dependent ductility factors. The proposed equations were relatively simple and provide a good estimation of mean ductility factors. Based on the proposed equation, ductility factors considering the site conditions can be evaluated in accordance with the present building codes.

• Journal of Advanced Research in Ocean Engineering
• /
• v.1 no.4
• /
• pp.198-210
• /
• 2015

This paper presents the damage assessment of a free-fall dropped object on the seabed. The damage to a dropped object totally depends on the relationship between the impact energy and the soil strength at the mudline. In this study, unexpected dropping scenarios were first assumed by varying the relevant range of the impact velocity, structure geometry at the moment of impact, and soil strength profile along the penetration depth. Theoretical damage assessments were then undertaken for a free-fall dropping event with a fixed final embedment depth for the structure. This paper also describes the results of a three-dimensional large deformation finite element analysis undertaken for the purpose of validation. The analyses were carried out using the coupled Eulerian-Lagrangian approach, modifying the simple elastic-perfectly plastic Tresca soil model. The validation exercises for each dropping scenario showed good agreement, and the present numerical approach was capable of predicting the behavior of a free-fall dropped object.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.10
• /
• pp.1841-1852
• /
• 1992

With the wide application of fiber-reinforced composite material in aircraft, space structures and robot arms, the design and manufacture of composite joints have become a very important research area because they are often the weakest areas in composite structures. In this study, the effects of the adhesive thickness, residual thermal stress on the torque capacity of the tubular single lap joints were studied. The torque capacity of the adhesive joints were experimentally determined and found to be inversely proprotional to the adhesive thickness. In order to match the experimental results to the theoretical analyses, the elastic-perfectly plastic material properties of the adhesive were used in the closed form solution. Also, the residual thermal stress of the joints were calculated by the finite element method and it was proved that the residual thermal stress could play an important role in the thick adhesive joints.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.40 no.2
• /
• pp.140-147
• /
• 1998

Since a structure carries out its given functions and purposes while it is always resisting against the external load, the capacity of the resistance in the structure within the range that will not collapse the structure itself becomes the important factor in the design of the structures. Therefore, many suggestions were proposed and noted for determining method of the collapse load. Some of the methods from the suggestions have been commonly used due to the considerations on their distinctive advantages such as the compactness of the conceptions and the convenience in the computation. However, in case when the variation becomes huge in the materials and load, the results would carry(have or contain) many uncertain elements. On the other hand, load incremental method which regards the characteristics of the probability must be more attainable method even though it might complicate the calculation. This study intends to develop a finite element model that uses the probabilistic load incremental method to estimate the collapse load, and also to compare the result of the analysis with the linear load incremental method and Turkstra's Rule.

• Steel and Composite Structures
• /
• v.2 no.5
• /
• pp.379-396
• /
• 2002

The paper describes the mechanical behavior of short concrete-filled steel tube (CFT) columns with circular section. The efficiency of the steel tube in confining the concrete core depending on concrete strength and the steel tube thickness was examined. Fifteen columns were tested to failure under concentric axial loading. Furthermore, a mechanical model based on the interaction between the concrete core and the steel tube was developed. The model employs a volumetric strain history for the concrete, characterized by the level of applied confining stress. The situation of passive confinement is accounted for by an incremental procedure, which continuously updates the confining stress. The post-yield behavior of the columns is greatly influenced by the confinement level and is related to the efficiency of the steel tube in confining the concrete core. It is possible to classify the post-yield behavior into three categories: strain softening, perfectly plastic and strain hardening behavior. The softening behavior, which is due to a shear plane failure in the concrete core, was found for some of the CFT columns with high-strength concrete. Nevertheless, with a CFT column, it is possible to use high-strength concrete to obtain higher load resistance and still achieve a good ductile behavior.

• Journal of the Korean Geotechnical Society
• /
• v.17 no.3
• /
• pp.41-50
• /
• 2001

본 연구는 모래사면의 언덕근처에 설치된 짧은 말뚝의 수평하중의 영향에 관한 것이다. 3차원 탄소성 유한요소법해석과 실내 모형실험의 결과를 비교하였다. 경사 30$^{\circ}$의 사면에 시공된 짧은 말뚝의 특성을 파악하기 위해, 사면언덕에서 모형말뚝까지의 거리를 3종류로 상이하게 하여, 모형실험을 실시하였다. 사용된 모래의 지반특성은 배수조건하의 삼축압축실험으로 결정하였다. 동시에 3차원 탄소성 유한요소법에 의한 수치해석결과와 모형실험결과를 비교하였다. 본 유한요소법의 해석에 있어서 모래지반을 탄성완전소성모델(Elastic-perfectly plastic model)로 가정하여, 파괴기준으로 Mohr-Coulomb 식과 소성 포텐셜에 대해서는 Drucker-Prager 식을 적용한 MC-DP 모델로 하였다. 이러한 MC-DP 모델의 구성식은 유한요소법에서 있어 계산치의 수렴에 유익하다. 3차원 탄소성 유한요소법에 의한 수치해석이 사질토 사면의 언덕 부근에 설치된 단하의 수평거동에 대한 파악에 유효하다는 것을 확인하였다.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2006.03a
• /
• pp.394-401
• /
• 2006

This study developed two dimensional finite element program(FE-SCP) for the analysis of a composite ground reinforced by sand compaction piles with a low area replacement ratio based on the Mohr-Coulomb elastic perfectly plastic constitutive model. Program FE-SCP give some conveniences to users such as automatic mesh generation according to the replacement ratio and the effective sand pile diameter in the post processor. Also, it contains optimum processor in calculation of In-situ stress equilibrium considering different coefficient of earth pressure between sand pile and surrounding clay. Estimated stress-strain behavior using FE-SCP and the measured one from a centrifuge test showed good agreement comparing to the result from a general finite element program.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.8 s.251
• /
• pp.873-879
• /
• 2006

To investigate applicability of the reference stress approach as simplified inelastic stress analysis to estimate local creep rupture, detailed finite element stress analyses of a T-piece pipe with different inner pressure and system loading levels are performed. The reference stresses are obtained from the finite element (FE) limit analysis based on elastic-perfectly-plastic materials, from which the local reference stress for creep rupture is determined from R5. The resulting inelastic stresses are compared with elastic stresses resulting from linear elastic FE calculations. Furthermore they are also compared with the stresses from full elastic-creep FE analyses. It shows that the stresses estimated from the reference stress approach compare well with those from full elastic-creep FE analysis, which are significantly lower than the elastic stress results. Considering time and efforts for full inelastic creep analysis of structures, the reference stress approach is shown to be a powerful tool for creep rupture estimates and also to reduce conservatism of elastic stress analysis significantly.