• Proceedings of the IEEK Conference
• /
• 2002.07a
• /
• pp.646-649
• /
• 2002

In this paper, a low-voltage CMOS squarer and a four-quadrant analog multiplier are presented. It is based on a source-coupled pair and a scaled-floating voltage generator which are modified to work as a voltage squaring and a sum/difference circuits. The proposed squarer/multiplier have been simulated with HSPICE, where -3㏈ bandwidth of 10MHz is achieved. The power consumption is about 0.6㎽, from a ${\pm}$1.5V supply, and the total harmonic distortion is less than 0.7%, with a 1.2V peak-to-peak 1MHz input signal.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.199-200
• /
• 2011

Load forecasting is very important for power system analysis and planning. This paper suggests yearly load forecasting of considering weekly normalization and seasonal load characteristics. Each weekly peak load is normalized and the average value is calculated. The new hourly peak load is seasonally collected. This method was used for yearly load forecasting. The results of the actual data and forecast data were calculated error rate by comparing.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.68-69
• /
• 2011

Realistic amounts of time delay are found to have significant effects on the average output LED current and on the critical inductor value at the boundary between the two conduction modes. Especially, the time delay can provide an accurate LED current for the peak current controlled (PCC) buck converter with a wide input voltage. Experimental results are presented for the PCC buck LED driver with constant-frequency controller.

• Journal of the Optical Society of Korea
• /
• v.14 no.4
• /
• pp.357-362
• /
• 2010

The joint transform correlator (JTC) has been the best known technique for pattern recognition and identification. This paper proposes a new technique of fringe adjustment by adopting a sinusoidal amplitude-modulated iterative filter convolved with an interference fringe pattern in the joint power spectrum (JPS) domain. The comparison of our new technique and other techniques is presented to show that the newly proposed technique can successfully improve both the correlation peaks and the peak signal-to-noise ratio (PSNR). Simulated results of enhanced interference fringes are also presented.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1233-1234
• /
• 2015

본 연구에서는 유전 물질인 Polydimethylsiloxane(PDMS)의 두께에 따른 마찰전기 에너지 수확소자의 출력 전압을 실험적으로 확인하였다. 동작 범위 5 mm, 주파수 5 Hz를 기준으로 접촉-분리 방식으로 소자를 측정하였으며 PDMS 두께가 $440{\mu}m$일 때 peak-to-peak 전압이 131.5 V가 측정되었다. 이는 측정 두께 중 가장 얇은 두께인 $115{\mu}m$의 출력 값인 8.47 V와 비교하여 약 15배 증가한 수치이다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.04b
• /
• pp.301-307
• /
• 1995

A monitoring technique of spindle fairure should be investirated prior to researcs of fairure diagnosis. This work is about monitoring of unbalanced shaft and defected bearings. The major work is done via experiments and the vibration signal is analysed means of power spectrum technique, and root mean squqre, peak-to-peak. Relationship is quantitatively investigated between defects and these monitoring paramenters.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.2
• /
• pp.407-410
• /
• 2010

This paper presents an advanced load allocation algorithm in Direct Load Control(DLC) system. It is important to aggregate a various demand side resource which is surely controllable at the peak power time for a successful DLC system. Previous load allocation algorithm appropriate for DLC system is based on interchanged information, but, this algorithm can not derive optimal solutions. In this paper, we develop the optimal algorithm and the new load allocation algorithm in polynomial time. The simulation results show that the proposed heuristic algorithm for DLC system is very effective.

• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.550-551
• /
• 2014

A discrete time domain modeling and analysis for the peak current controlled (PCC) buck LED driver is presented in this paper. The design guidelines and experimental results for the PCC buck LED driver are presented.

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.106-108
• /
• 2020

This paper introduces a new pulse-width modulation (PWM) method to reduce common-mode voltages (CMVs) and compare its performance with other reduced CMV-PWM (RCMV-PWM) methods. To avoid the use of zero-vectors which cause high CMV peaks, the introduced method splits every reference vector into two vectors such that the peak-to-peak magnitude of CMV is reduced by one-third of conventional space-vector PWM (SVPWM). The performance of RCMV-PWMs altered by the modulation index are analyzed with simulation results.

• Proceedings of the KIPE Conference
• /
• 2013.11a
• /
• pp.227-228
• /
• 2013

The paper is related to smart maximum power system based on program logic. Especially, this system compares the total demand power with the target power by using the signal from the digital kilo watt meter. Based on the power information by the maximum power control equipment the consumed future power is anticipated. In addition, through consumed future power the controllable target power is set, and it applies on the maximum power control equipment. User or manager would control the load efficiently through the simple programming which could control load based on the control sequence and relay. So this system could control load more efficient and stable. Also the conventional load control circuit is not needed. Therefore, it is possible to improve the simple system configuration, which is resulted in cost effective and time saving. So this system is anticipated on time and coast.