• Journal of the Korean Wood Science and Technology
• /
• 제38권2호
• /
• pp.159-164
• /
• 2010

Nine compounds, caffeic acid, naringenin, apigenin, luteolin, kaempferol, verbascoside, isoverbascoside, isocampneoside II, and cistanoside F, were isolated from the EtOAc and n-BuOH fractions of P. coreana bark. The structures of these compounds (1-9) were elucidated by spectroscopic methods and literature data. All the isolates were subjected to in vitro bioassay to evaluate their inhibitory activity against rat lens aldose reductase. Among these, compounds 6 and 8 indicated the significant inhibitory activity on rat lens aldose reductase with $IC_{50}$ values of 2.67 and 5.59 ${\mu}M$, respectively. Especially, The inhibition activity of acteoside was 3.9 times better than that of quercetin as a positive control (10.6 ${\mu}M$). These results suggested that phenylethanoid glycosides are likely to be the potential compounds for the prevention and/or treatment of diabetic complications.

• Journal of the Korean Wood Science and Technology
• /
• 제31권6호
• /
• pp.15-21
• /
• 2003

Image processing technique was adapted for exploring the more convenient ways to investigate the drying characteristics of wood. The acquisition of information about drying characteristics is indispensable for the development or improvement of dry-kiln schedules. A small internal fan type wood dry kiln was combined with image-processing and data-acquisition systems to monitor continuously the formation of checks and moisture reduction during drying. All the images and data were analyzed to improve or estimate the dry-kiln schedules and predict the drying time which would be required to dry green wood to 10% moisture content in internal fan type kiln. Samples of 20 mm- and 50 mm-thick Metasequoia glyptostrobodies, Paulownia coreana Uyeki, Pinus densiflora Sieb. Et Zucc., Platanus occidentalis L., Quercus acutissima and Robinia pseudo-acacia were used to verify the potentiality of this technique.

• Journal of the Korean Wood Science and Technology
• /
• 제29권4호
• /
• pp.16-24
• /
• 2001

함수율은 목재의 효율적인 가공을 위한 기본적인 정보 중에서 가장 중요한 것의 하나이다. 그러나 기존의 열풍식 전건법으로는 수 시간에서 수일이 소요될 정도로 매우 긴 시간이 소요되므로 산업현장에서 적용하기에는 불편하다. 본 연구에서는 가정용 마이크로웨이브 오븐을 응용하여 수 분~수십 분내에 목재 시편의 함수율을 전건법에 의해 측정할 수 있는 기술을 개발하고자 하였다. 국산 3수종에 대하여 마이크로웨이브-전건실험을 수행한 결과 일반 열풍식 전건법에 비하여 전건시간을 1/7~1/10 수준으로 크게 줄일 수 있었고 일반 열풍식 전건법 과 비교하여 전건상태에서 0.1~0.2 g 정도의 편차만 나타내어 함수율 및 전건무게를 신속하고 정확하게 얻을 수 있도록 해주므로써 효율적인 목재건조를 수행하는데 도움이 될 것으로 기대된다.

• 농업과학연구
• /
• 제28권2호
• /
• pp.125-131
• /
• 2001

백색부후균 Trametes versicolor(CV5) 균주에 의한 wood lignin의 분해능을 조사하였다. CV5는 활엽수와 침엽수에 속하는 여러 수종의 프로토 리그닌 분해 시 활엽수에 한해서 분해되는 특성을 보였으며, 특히 상수리나무에서 33.5%의 가장 높은 리그닌이 분해되었다. 리그닌 분해에 관련된 phenoloxidase 분비능을 Bavendamm 시험을 통해 검토한 결과 CV5는 지금까지 연구된 우수 백색 부후균과 같은 유사 반응 형태를 나타내고 있음을 확인하였다. 또한 상수리 목재 chip표면에 CV5의 균사가 생육하면서 목재조직이 부후된 상태를 주사전자 현미경으로 관찰한 결과 목섬유 및 도관에서 균사의 침투와 목재조직의 분해를 확인하고 리그닌에 대한 높은 선택적 분해력을 갖고 있음을 구명하였다.

• Journal of the Korean Wood Science and Technology
• /
• 제36권6호
• /
• pp.1-12
• /
• 2008

주요 국산재의 여러 가지 응용물성을 지난 3년에 걸쳐 조사하였다. 전보(강 외 4인 2008, 변 외 5인 2008)에 이어 본보에서는 우리나라의 활엽수 주요 수종인 백합나무, 거제수나무, 오동나무를 재료로 사용하였다. 매년 동일한 장치와 실험조건으로 실험하였기 때문에 모든 수종에 대한 결과를 상호 비교 할 수 있었다. 수분흡착성 실험은 80메시 목분을 이용하였으며, 넓은 범위의 상대습도조건에 따른 평형 함수율과 흡착등온선을 구하였다. 열전도율과 열확산률은 열선열전도장치를, 전기의 부피저항률과 저 항은 고전기저항계를 이용하여 측정하였다. 정목재와 판목재의 열적 전기적 특성차이가 관찰되었는데 이는 해부학적 차이에 의한 것으로 보인다. 음향적 성질은 음향측정시스템을 사용하여 동적탄성률, 내부마찰을 측정하였다. 본 논문의 결과들은 목재구조물 설계, 휴대용 목재수분계 보정, 음향적 성질 등에 필요한 기본 자료를 제공한다.

• Journal of the Korean Wood Science and Technology
• /
• 제18권4호
• /
• pp.65-78
• /
• 1990

For the purpose of Improving the sounding boards for the conventional GAYAKUM, I was making approximately 202 specimens of radial board, 371 specimens of tangential board by cutting along the grain and the part of stem and 31 specimens of the disjointed traditional GAYAKUM made in Paulownia coreana. And it was conducted to measure specific gravity, dynamic Young's modulus, internal friction, resonant frequency, velosity of sound and width of annual ring by the method of the frexural vibration in a free-free bar in the audio frequency range. And it confirmed the juvenile wood by measuring wood fiber length of specimens. It was also conducted to investigate dynamic properties and moisture absorption by various heat-treatment and to test dynamic Young's modulus and internal friction for the disjointed conventional GAYAKUM. The results obtained were summarized as follow: 1. The Juvenile wood is located within about 7 annual rings from the pith in Paulownia coreana. 2. As increased with the specific gravity, the dynamic Young's modulus had more and more increased, but the internal friction had slightly decreased. 3. I think that radial board would be good for sounding board wood. because radial board is higher than tangential board in dynamic Young's mudulus and internal friction is lower than tangential board. 4. The value of mean dynamic Young's modulus on the conventional GAYAKUM, radial board and tangential board of 604 samples is $0.4283\pm0.037(\times10^{11}dyne/cm^2)$, $0.4316\pm(\times10^{11}dyne/cm^2)$ and $0.4234\pm0.112(\times10^{11}dyne/cm^2)$ respectively. The value of the radial board showed little higher than that of conventional GAYAKUM, but It had a similar tendency between conventional GAYAKUM and tangential board. 5. The annual ring width by four aspect is more narrow in north and west than that of others. 6. The values of specific gravity and dynamic Young's modulus in the mature wood showed higher than those of juvenile wood. 7. As the grain angle in the butt wood more increased to bark from pith, the dynamic Young's modulus were low. Then it was not good for sounding board. 8. It appeared that the heat-treatment for sounding board wood had a more effect to do the treatment of hotiron on surface after heat-treatment during 24 hours in $60^{\circ}C$ temperature. 9. As increased with the temperature, the rate of moisture absorption of heat-treatment wood had decreased. In conclusion, I thought that the sounding board wood for GAYAKUM would had the most effect to do the treatment of hotiron on surface after heat-treatment during 24 hours in $60^{\circ}C$ temperature using the radial board of mature wood.

• Journal of the Korean Wood Science and Technology
• /
• 제46권6호
• /
• pp.681-691
• /
• 2018

The typical methods of mercury intrusion porosimetry (MIP) and capillary flow porometry (CFP) were used to evaluate the pore size of cross-section of wood and the effect of the pore structure on the permeability of wood was analyzed in this study. The results of this study were as followings: The pore size of wood measured by CFP was larger than that measured by MIP except for Lime tree, Korean red pine and Paulownia. Among the three pore types of porous materials defined by IUPAC (through pores, blind pores, and closed pores), only through pores are related to permit fluid flow. MIP measures the pore size of both through pores and blind pores, while CFP measures the pore size of only constricted through pores. Therefore, pore size measured by MIP was not related to gas permeability, however pore size measured by CFP had a proportional relationship with gas permeability.

• Journal of the Korean Wood Science and Technology
• /
• 제40권5호
• /
• pp.303-310
• /
• 2012

Heat treatment improves dimensional stability and sound absorption properties of wood. However, mechanical properties of wood can be deteriorated during the heat treatment. The effect of heat treatment on the bending strength and hardness of wood for Korean paulownia, Pinus densiflora, Lidiodendron tulipifera and Betula costata were measured. The heat treatment temperature has been investigated at $175^{\circ}C$ and $200^{\circ}C$, respectively. The results showed that the weight and density of wood decreased after heat treatment. It was found that the density by heat treatment was lower at $200^{\circ}C$ than that at $175^{\circ}C$. And, MOE increased with the reduced density. On the contrary, MOR and hardness decreased. In all conditions, It was found that there was a high correlation of 1% level between bending modulus of elasticity and modulus of rupture.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 추계학술대회(한국공작기계학회)
• /
• pp.32-37
• /
• 2001

In the present industry, there are necessary to cut not only iron metals but also non-ferrous metals such as aluminum, brass, plastic and wood(Paulownia). therefore it had been made the studies of non-ferrous metals by many scientists. we hope this kind of study will continue. The purpose of this study is to conduct the basic experiment about influencing of change the side rake angle at turning of non-ferrous metals. As the results, the surface roughnesses were on the increase with a increase of side-rake angle at the case of the plastic, brass, aluminum, and paulownia.

• 펄프종이기술
• /
• 제44권5호
• /
• pp.63-71
• /
• 2012

This study was carried out to investigate pulping properties of the forest biomass arising from the national forest management operation. The forest biomass was collected and classified into many groups according to their species and age. After the chips were made from the forest biomass, the measurement of chip size and chemical analysis were performed. To make the pulps from the forest biomass, the kraft pulping was applied and thereafter the physical and optical properties of kraft pulps were measured. The pulp fibers from the forest biomass had the similar mean fiber length, but their properties became different according to wood species and ages. Differently from the other species, kraft pulps from chestnut wood had the highest kappa number. Acacia, paulownia and chestnut woods made kraft pulps with lower tensile strength and brightness than the others. It could be concluded that acacia, paulownia and chestnut woods must be screened out in order to make a good quality of kraft pulps while being collected during Forest Management Operation.