• 한국자동차공학회논문집
• /
• 제15권6호
• /
• pp.144-150
• /
• 2007

In recent years, the particle number emissions rather than particulate mass emissions in automotive engine have become the subject of controversial discussions. Recent results from the health effects studies imply that it is possible that particulate mass does not properly correlated with the variety of health effects attributed to diesel exhaust. So, the concern is instead now focusing on nano-sized particles emitted from I. C. engine. This study has been performed for the better understanding about the engine nano-particle for 3-measurement systems with different measuring principle. Firstly, EEPS is a newly introduced instrument for size distribution measurement of engine exhaust particles. It can measure nano-particles with an adequate resolution and in real time. In this study, the characteristics of EEPS were compared with ELPI and SMPS. As a research results, EEPS showed a same effect of engine load on the size distribution with ELPI and SMPS. But the quantitative results of EEPS were more similar to SMPS than ELPI, because the EEPS and SMPS use a same principle for classifying particles by size. The capability for transient measurement of EEPS was equivalent to that of ELPI.

• 한국식생활문화학회지
• /
• 제34권3호
• /
• pp.334-342
• /
• 2019

In this study, the effects of different varieties and particle sizes of dry milled rice flour on Jeolpyeon quality were investigated. Classify particle size of dry milled rice flour according to rice variety into 50, 100, and $150{\mu}m$. A particle size of $50{\mu}m$ in the varieties Boramchan and Hanareum resulted in the highest damaged starch contents (p<0.05). Additionally, the Boramchan and Hanareum varieties had the highest water absorption index (WAI) values (p<0.05). Analysis of the gelatinization characteristics of dry milled rice flour according to varieties revealed the peak viscosity of Dasan and Hanareum was high (p<0.05), regardless of particle size, while the breakdown was highest for Hanareum at all particle sizes (p<0.05). The moisture content of Jeolpyeon made with Boramchan varied between 48.83 and 53.64% among particle sizes, with no significant differences relative to the control. The hardness of the control was 3.15 kg, while the hardness of Jeolpyeon made with Boramchan decreased significantly 2.60-2.63 kg (p<0.05).

• Macromolecular Research
• /
• 제9권2호
• /
• pp.122-128
• /
• 2001

Monodisperse composite latex particles with size of ca. 300 nm, which consist ofn-butyl acrylate as a soft phase and methyl methacrylate as a hard phase with different morphology, were synthesized by seeded multi-stage emulsion polymerization. Three types of composite latex particles including random-, core/shell-, and gradient-type particles were obtained by using different monomer feeding methods during semi-batch emulsion polymerization. Effect of poly(butyl acrylate)-poly(methyl methacrylate) rubber particle morphology on the mechanical and rheological properties of rubber toughened poly(methyl methacrylate) was investigated. Among three different rubber particles, the gradient-type rubber particle showed better toughening effect than others. No significant variation of rheological property of poly(methyl methacrylate)/rubber blends was observed for the different rubber particle morphology.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제4권4호
• /
• pp.403-411
• /
• 2012

This study presents the nano-sized particle emission characteristics from a small turbocharged common rail diesel engine applicable to prime and auxiliary machines on marine vessels. The experiments were conducted under dynamic engine operating conditions, such as steady-state, cold start, and transient conditions. The particle number and size distributions were analyzed with a high resolution PM analyzer. The diesel oxidation catalyst (DOC) had an insignificant effect on the reduction in particle number, but particle number emissions were drastically reduced by 3 to 4 orders of magnitude downstream of the diesel particulate filter (DPF) at various steady conditions. Under high speed and load conditions, the particle filtering efficiency was decreased by the partial combustion of trapped particles inside the DPF because of the high exhaust temperature caused by the increased particle number concentration. Retarded fuel injection timing and higher EGR rates led to increased particle number emissions. As the temperature inside the DPF increased from $25^{\circ}C$ to $300^{\circ}C$, the peak particle number level was reduced by 70% compared to cold start conditions. High levels of nucleation mode particle generation were found in the deceleration phases during the transient tests.

• 한국재료학회지
• /
• 제23권9호
• /
• pp.510-516
• /
• 2013

Fly ash is one of the aluminosilicate sources used for the synthesis of geopolymers. The particle size distribution of fly ash and the content of unburned carbon residue are known to affect the compressive strength of geopolymers. In this study, the effects of particle size and unburned carbon content of fly ash on the compressive strength of geopolymers have been studied over a compositional range in geopolymer gels. Unburned carbon was effectively separated in the $-46{\mu}m$ fraction using an air classifier and the fixed carbon content declined from 3.04 wt% to 0.06 wt%. The mean particle size ($d_{50}$) decreased from $22.17{\mu}m$ to $10.79{\mu}m$. Size separation of fly ash by air classification resulted in reduced particle size and carbon residue content with a collateral increase in reactivity with alkali activators. Geopolymers produced from carbon-free ash, which was separated by air classification, developed up to 50 % higher compressive strength compared to geopolymers synthesized from raw ash. It was presumed that porous carbon particles hinder geopolymerization by trapping vitreous spheres in the pores of carbon particles and allowing them to remain intact in spite of alkaline attack. The microstructure of the geopolymers did not vary considerably with compressive strength, but the highest connectivity of the geopolymer gel network was achieved when the Si/Al ratio of the geopolymer gel was 5.0.

• 한국세라믹학회지
• /
• 제40권2호
• /
• pp.132-138
• /
• 2003

출발물질의 종류와 몰비 혼합 방법, 숙성, 결정화 온도와 결정화 시간 등 제올라이트 입자를 합성하는 조건이 FAU 형 제올라이트의 입자크기에 미치는 영향을 연구하였다. 동일한 출발물질이라도 혼합 경로에 따라 생성물의 결정상이 달랐다. 일반적으로 숙성과정을 거친 경우, 특히 숙성온도가 낮은 쪽이 입자 크기가 작았다. 2단계의 혼합겔 제조 방법을 거치는 경우 결정화 기간은 크게 단축되고 입자 크기도 작아졌으나. 1단계에서 제조된 2종의 혼합겔을 모두 숙성하지 않는 경우에는 결정화 시간은 단축되지만, 입자크기는 작아지지 않았다. 액상규산나트륨과 알루민산나트륨, 수산화나트륨을 출발물질로 하여. 저농도와 고농도의 혼합겔을 1차 제조하고, 이 혼합겔을 각각 숙성하고 다시 혼합하여 숙성하는 방법으로 결정화 시간을 단축하고 평균입경 0.4$\mu$m. 비표면적 838 $m^2$/g의 우수한 특성을 가지는 FAU혈 제올라이트를 합성하였다.

• 한국식생활문화학회지
• /
• 제25권1호
• /
• pp.70-75
• /
• 2010

The object of this study was to investigate the effects of rice particle size on the physicochemical properties of beef-rice porridge. The pH of beef-rice porridge was decreased as compared to that of the control, while the redness of beef porridge increased according to rice particle size. The viscosity of flour in the beef-rice porridge was the highest among three porridges, at $40^{\circ}C$. The protein content of beef-rice porridge was increased 3-fold over that of rice porridges. The total amino acid content of the beef-rice porridge was 3071.2 mg/100 g, and that of rice porridge was 1147.5 mg/100 g. As compared to rice porridge, the maximum amounts of the amino acids Lys and Thr were increased beef-rice porridge. Sensory evaluation results showed that the beef-rice porridge with a particle size half that of rice had the highest scores in color, taste, texture, and overall preference. Based on these results, it is suggested that beef-rice porridge with a particle size half (0.7-2.5 mm) that of rice has optimal quality in terms of both physicochemical and sensory properties.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.508-511
• /
• 2004

This study focused on the effect of autonomic microcapsules on the mechanical properties of structural material. Several types of microcapsules with healing agents were manufactured by varying agitation speed of high speed stirrer. The size distribution of microcapsules was measured by a particle size analzer. The epoxy specimens embedded with microcapsules were manufactured and the degree of cure of such epoxy specimen was measured by a differential scanning calorimetry. The tensile modulus and tensile strength in epoxy specimens embedded with microcapsules were evaluated in order to investigate the effects of microcapsules on mechanical properties of structural materials. The configuration of microcapsules and morphology of fracture surfaces for the epoxy specimen were examined by an optical microcope and a scanning electron microscope. According to the results, tensile strength of the epoxy specimen embedded with microcapsules was indicated a little reduction, but tensile modulus was not much affected on microcapsules.

• 대한기계학회논문집B
• /
• 제21권1호
• /
• pp.132-139
• /
• 1997

Spray characteristics of external mixing sonic twin-fluid atomization nozzles are investigated experimentally. Particle sizes are measured by the Fraunhofer diffraction method using the Malvern particle analyzer, and their radial distributions are obtained using the tomographical transformation technique. The spatial distribution of SMD shows that the drop size increases in the radial direction at a fixed liquid flow rate, and the distribution is getting uniform rapidly as the atomizing gas pressure increases. The SMD decreases as the liquid flow rate increases at a fixed GLR. It is found that the atomization efficiency of the flush type sonic nozzle is superior to that of protrusion type. The effect of laser beam diameter of the particle analyzer on the spatial SMD distribution is minor at present experimental conditions.

• 한국물환경학회지
• /
• 제29권2호
• /
• pp.170-175
• /
• 2013

Achieving very low phosphorus levels in treated wastewater will require the installation of additional treatment. Phosphorus removal experiments by chemical coagulation were carried out for the effluent of wastewater treatment plant in this study. TP (total phosphorus) or phosphate were highly related to the addition of PAC (poly aluminium chloride) which is one of the inorganic coagulants. But, organic polymer did not significantly affect the phosphorus removal efficiency. Polymer affected the flocculation of particle especially particle matter less than 10 micrometer so, the number of micro particles was decreased by polymer dose. Chlorination would not affect on chemical coagulation process and TP and turbidity could be effectively removed by the co-addition of PAC and polymer.