• Archives of Pharmacal Research
• /
• v.18 no.6
• /
• pp.427-433
• /
• 1995

A microscopic mass balance approach has hsown that the initial saturation (Is), absorption number (An), dose number (Do), and dissolution number (Dn) are four fundamental dimensionless parameters that can be used to estimate the fraction dose absorbed (F)l of suspensions of poorly soluble drugs in humans. The dissolution number of a drug increases with decreasing its particle size. The effect of micronization on F for suspensions was investigated in terms of Dn. About 90% of maximal F can be achieved at $Dn{\approx}2$. Increasing the solubility of a drug results in better oral absorption through increasing Dn and decreasing the solubility of a drug results in better oral absorption through increasing Dn and decreasing Do. The fractions dose absorbed of digoxin, griseofulvin, and benoxaprofen agree with predicted F values sorbed by reducing particle size, while absorption of drugs with high Do and low Dn is limited by solubility and requires higher solubility to enhance the fraction dose absorbed in addition to micronization. Solubility at the physiological pH should be used for the estimation of the fraction dose absorbed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.2
• /
• pp.138-143
• /
• 2004

CMP (Chemical Mechanical Polishing) technology for global planarization of multilevel interconnection structure has been widely studied for the next generation devices. Among the consumables for CMP process, especially, slurry and their chemical compositions play a very important role in the removal rates and within-wafer non-uniformity (WIWNU) for global planarization ability of CMP process. However, CMP slurries contain abrasive particles exceeding 1 ${\mu}{\textrm}{m}$ size, which can cause micro-scratch on the wafer surface after CMP process. Such a large size particle in these slurries may be caused by particle agglomeration in slurry supply-line. In this work, to investigate the effects of agglomeration on the performance of oxide CMP slurry, we have studied an aging effect of silica slurry as a function of particle size distribution and aging time during one month. We Prepared and compared the self-developed silica slurry by adding of alumina powders. Also, we have investigated the oxide CMP characteristics. As an experimental result, we could be obtained the relatively stable slurry characteristics comparable to aging effect of original silica slurry. Consequently, we can expect the saving of high-cost slurry.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.4
• /
• pp.91-98
• /
• 2012

This study was carried out in order to evaluate the effects of ultra fine precipitated calcium carbonate (UFPCC) on properties of coating color, coated paper and off-set printability. It was found that blending of UFPCC increased the low-shear viscosity and water retention of coating color. The smaller the particle size, the more significant the effect of it. When the blending ratio of UFPCC was increased, brightness, whiteness and opacity of the coated paper were improved, while paper gloss was decreased due to the increase in roughness. When the UFPCC with the average particle size of $0.12{\mu}m$ was used, the ink receptivity during off-set printing was improved while print gloss was maintained or a little decreased. It was also observed that the dry-pick and wet-pick strength of coated paper were improved by the use of UFPCC. In conclusion, it is possible to produce the low gloss matt paper with the use of UFPCC since it could improve the optical properties and ink receptivity of coated paper.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.3
• /
• pp.1-7
• /
• 2009

Talc as a coating pigment has been developed in order to replace GCC and clay for matte grade and has received much attention due to various advantages including good gravure printability. In order to elucidate the effects of talc on gravure printability, model papers were produced with three kinds of coating talc whose particle size and brightness are different. Physical properties related to surface and structure and the gravure printability of the sample were tested. Coating color with talc showed lower viscosity than that with clay. For both matte and art grades, talc tended to give lower gloss than day. The smaller the particle size of talc, the better properties in the coating color viscosity and water retention. When the particle size of talc was small enough, the surface roughness of the coated paper produced with talc was similar to that with clay while larger talcs produced rougher surface than clay. On top of that, application of talc improved compressibility and gravure printability of coated paper.

• Journal of the Korean GEO-environmental Society
• /
• v.23 no.1
• /
• pp.5-13
• /
• 2022

In tropical regions, lateritic soil is frequently used in road embankment. However, it is one of the sources of road failure owing to its low strength. Generally, cement and lime are used as stabilizers for lateritic soil, but they are not environmentally friendly. Some studies try to use eggshells, for they are food waste and share the same chemical composition as lime. Previous researchs have shown that eggshell powder could enhance the strength of lateritic soil. This research investigated the effect of particle size of the eggshell powder and the effect of the protein-membrane presence in the eggshell on stabilizing capacity of soil. Through laboratory tests, unconfined compressive strength was examined for various particle sizes. The particle size of eggshell powder ranging between 150 ㎛ and 88 ㎛ was appropriate size that made an excellent stabilizer at 3% concentration. On the other hand, the protein-membrane reduced the stabilizing ability of the eggshell powder when the content of eggshell powder is less than 4% in soil. Numerical analysis of road embankment was performed based on the results obtained in the laboratory tests. It is shown that the eggshell powder has improved the stability of the sub-base of the road embankment.

• Journal of Soil and Groundwater Environment
• /
• v.27 no.4
• /
• pp.63-74
• /
• 2022

In analyzing heavy metals in soil samples, the standard protocol established by Korean Minstry of Environment (KSTM) requires two different pretreatments (A and B) based on soil particle size. Soil particles < 0.15 mm in diameter after sieving are directly processed into acid extraction (method A). However, if the quantity of soil particles < 0.15 mm are not enough, grinding of the particles within 0.15 mm ~ 2 mm is required (method B). Grinding is often needed for some field samples, especially for the soil samples retrieved from soil washing process that contain relatively large-sized soil grains. In this study, two soil samples with different particle size distribution were prepared and analyzed for heavy metals concentrations using two different pretreatment to investigate the effect of grinding. The results showed that heavy metal concentrations tend to increase with the increase of the fraction of small-sized particles. In comparison of the two pretreatments, pretreatment A yielded higher heavy metal concentration than pretreatment B, indicating significant influence of grinding on analytical results. This results suggest that the analytical values of heavy metals in soil samples obtained by KSTM should be taken with caution and carefully reviewed.

• Clean Technology
• /
• v.16 no.4
• /
• pp.254-257
• /
• 2010

[ $Mg(OH)_2$ ]slurry was prepared by using natural mineral brucite exploited from Liaoning province in China, and its de-SOx efficiency was examined. The effect of difference in particle size distribution of brucite and activation by hydrothermal treatment were investigated. The de-$SO_2$ efficiency of a finely-milled brucite sample below 1000 mesh with narrow particle size distribution was higher than that of the sample below 80 mesh. On the other hand, the de-$SO_2$ efficiency of brucite sample below 80 meshes was significantly improved by the hydrothermal treatment at 363 K tor 3 h.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.188-197
• /
• 2010

This paper presents experimental results of a series of 1-g shaking table model tests performed on end-bearing single piles and pile groups to investigate the effect of particle size on the dynamic behavior of soil-pile systems. Two soil-pile models consisting of a single-pile and a $4{\times}2$-pile group were tested twice; first using Jumoonjin sand, and second using Australian Fine sand, which has a smaller particle size. In the case of single-pile models, the lateral displacement was almost within 1% of pile diameter which corresponds to the elastic range of the pile. The back-calculated p-y curves show that the subgrade reaction of the Jumoonjin-sand-model ground was larger than that of the Australian Fine-sand-model ground at the same displacement. This phenomenon means that the stress-strain behavior of Jumoonjin sand was initially stiffer than that of Australian Fine sand. This difference was also confirmed by resonant column tests and compression triaxial tests. And the single pile p-y backbone curves of the Australian fine sand were constructed and compared with those of the Jumoonjin sand. As a result, the stiffness of the p-y backbone curves of Jumunjin sand was larger than those of Australian fine sand. Therefore, using the same p-y curves regardless of particle size can lead to inaccurate results when evaluating dynamic behavior of soil-pile system. In the case of the group-pile models, the lateral displacement was much larger than the elastic range of pile movement at the same test conditions in the single-pile models. The back-calculated p-y curves in the case of group pile models were very similar in both sands because the stiffness difference between the Jumoonjin-sand-model ground and the Australian Fine-sand-model ground was not significantly large at a large strain level, where both sands showed non-linear behavior. According to a series of single pile and group pile test results, the evaluation group pile effect using the p-multiplier can lead to inaccurate results on dynamic behavior of soil-pile system.

• Journal of Powder Materials
• /
• v.19 no.4
• /
• pp.278-284
• /
• 2012

$Al_2O_3$ foam is an important engineering material because of its exceptional high-temperature stability, low thermal conductivity, good wear resistance, and stability in hostile chemical environment. In this work, $Al_2O_3$ foams were designed to control the microstructure, porosity, and cell size by varying different parameters such as the amount of amphiphile, solid loading, and stirring speed. Particle stabilized direct foaming technique was used and the $Al_2O_3$ particles were partially hydrophobized upon the adsorption of valeric acid on particles surface. The foam stability was drastically improved when these particles were irreversibly adsorbed at the air/water interface. However, there is still considerable ambiguity with regard to the effect of process parameters on the microstructure of particle-stabilized foam. In this study, the $Al_2O_3$ foam with open and closed-cell structure, cell size ranging from $20{\mu}m$ to $300{\mu}m$ having single strut wall and porosity from 75% to 93% were successfully fabricated by sintering at $1600^{\circ}C$ for 2 h in air.

• Journal of Adhesion and Interface
• /
• v.12 no.1
• /
• pp.1-10
• /
• 2011

An automated reaction calorimeter was used to directly monitor the rate of emulsion polymerization of vinyl acetate using poly(vinyl alcohol) (PVAs) having different degrees of blockiness. By using this technique in conjunction with other off-line measurements of the evolution of particle size distributions, important details of the process were observed. No constant graft rate period was observed for both low and high initial monomer-water ratios. The gel effect was observed for the low monomer-water ratio recipe. The particle size distributions were broad (particle diameter 40~100 nm) and bimodal. Continuous nucleation was observed to be accompanied by 'limited aggregation' and flocculation during the particle growth stages. It was speculated to be due to the occurrence of the extensive 'limited aggregation' and chain transfer to PVA leading to grafting.