• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.3
• /
• pp.442-450
• /
• 2001

Experiments were carried out on agglomeration of bipolarly charged particles in an alternating current electric field. Laboratory-scale setup was built and experiments were conducted at atmospheric condition. DOS(Di-octyl Sebacate) particles with 100% purity were generated by an atomizer. The particles were branched into two, each of which passed through a wire-to-plate type charging section where a positive or a negative DC high voltage was applied and was charged positively or negatively. These bipolarly charged particles together passed through an agglomeration section where an $\pm$20kV AC power was applied between two plates. The resident time in the agglomeration section was adjusted as l sec. Particle sampling was made by a cascade impactor (MOUDI). The effect of agglomeration system on the reduction ratio of particles below l ㎛ was 42∼45%. Effect of AC frequency on the particle size distribution was found insignificant.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.10a
• /
• pp.459-460
• /
• 2009

• Asian-Australasian Journal of Animal Sciences
• /
• v.22 no.10
• /
• pp.1377-1385
• /
• 2009

Effect of inclusion of hard vs. soft wheat bran with different particle size on diet digestibility, growth performance and some slaughter traits was evaluated in fattening rabbits. Four isonitrogenous and isocaloric diets were used according to the origin of wheat bran (hard (HWB) - Triticum durum - and soft (SWB) - Triticum aestivum) combined with wheat bran particle size sieved by 2 mm (fine: 2) or by 8 mm (coarse: 8) in a bifactorial (2${\times}$2) study. A growth trial was conducted to measure the effect of treatments on performance in one hundred and twenty New Zealand White${\times}$Californian rabbits fed experimental diets from 50 to 87 days of age. Faecal apparent digestibility was determined within the last week in twenty animals per diet. Digestibility of nutrients was higher (p<0.05) in the diet containing HWB2, except for crude protein, ether extract and ash, than fine and coarse soft wheat bran diets. Final live weight, feed intake and feed consumption of rabbits on the diet with fine hard wheat bran were higher and resulted in greater daily weight gains (p<0.01) than for animals on the other diets. The slaughter yield and percentage value of organs were not significantly (p>0.05) affected by the diets fed; however, the diet containing fine hard wheat bran led to lower (p<0.05) percentages of skin, abdominal fat and carcass drip loss than the other dietary treatments. It is concluded that fine hard wheat bran can be better included in the diet than soft wheat bran to maximize growth performance without affecting carcass traits of fattening rabbits.

• Journal of the Korean Ceramic Society
• /
• v.44 no.10
• /
• pp.562-567
• /
• 2007

To precipitate the complex gels of the pH 6, 7, 8, 9 included in a flux and an aluminum hydroxides gel, an aqueous solution of a mixture of $Na_2CO_3\;and\;Na_2PO_4{\cdot}12H_2O$ was added with stirring in an aqueous solution of a mixture of $Al_2(SO_4){_3}{\cdot}18H_2O,\;Na_2SO_4\;and\;K_2SO_4$, and then the complex gels were aged in 20 h at $90^{\circ}C$. As the hydrolysis pH changed, it had an effect on the physical properties such as the crystal structure, crystal morphology and a phase transition temperature of the AlO(OH) gel, and also on the crystal structure, crystal morphology, particle size and particle size distribution of the ${\alpha}-Al_2O_3$ platelets prepared by molten-salt precipitation. Also, in this study, the complex gels were crystallized at $1,200^{\circ}C$ and thereafter dried at $110^{\circ}C$, and then it was investigated to effect of the hydrolysis pH on the crystal structure, morphology and particle size distribution of the ${\alpha}-Al_2O_3$ platelets crystals using XRD, DTA, SEM and particle size analyzer.

• Journal of Korea Foundry Society
• /
• v.23 no.4
• /
• pp.195-203
• /
• 2003

Hyper-eutectic Al-Si alloy is used much to automatic parts and material for the electronic parts because of the low coefficient of thermal expansion, superior thermal stability and superior wear resistance. In this work, A390 alloy specimens were fabricated for control of the Si particle size by various processes, such as spray-casting, permanent mold-casting and squeeze-casting. To minimize the effect of microporosity of the specimens, hot extrusion was carried out under equal condition. Each specimens were evaluated tensile properties at room temperature and thermal expansion properties in the range from room temperature to 400$^{\circ}C$. Ultimate tensile strength and elongation of the spray-cast and extruded specimens which have fine and well distributed Si particles were improved greatly compare to the permanent mold-cast and extruded ones. Specimens which have finer Si particles showed higher ultimate tensile strength and elongation than those having large Si particle size, and coefficient of thermal expansion of the specimens increased linearly with Si particle size. In case of the repeated high temperature exposures, thermal expansion properties of the spray-cast and extruded specimens were found to be more stable than those of the others due to the effect of fine and well distributed Si particles.

• Polymer(Korea)
• /
• v.35 no.5
• /
• pp.451-457
• /
• 2011

The effect of latex particle size on rheological and electrical properties of latex-blended polystyrene (PS)/multi-walled carbon nanotube (MWCNT) nanocomposites was investigated. Mono-dispersed PS particles synthesized either by emulsifier-free emulsion polymerization or by dispersion polymerization were mixed with MWCNTs under ultrasonication, and freeze-dried to prepare the nanocomposites. As the MWCNT content increased, storage modulus, complex viscosity and electrical conductivity were substantially increased. The increase of storage modulus and complex viscosity was higher for larger PS particles. The effect of particle size on electrical properties was different depending on MWCNT content. With lower MWCNT content, the nanocomposite prepared by smaller PS particles showed higher electrical conductivity, but the opposite result was given as the content increased.

• Elastomers and Composites
• /
• v.58 no.4
• /
• pp.179-190
• /
• 2023

The effect of the particle size and silica structure on the wear behavior of Silica/Styrene-Butadiene Rubber (SBR) compounds was investigated using a blade-type abrader and the findings were compared with those obtained with an Akron abrader. The compensated characteristic parameter (Ψ_c), which was the contributory factor of the combined effect of the particle size and filler structure, was introduced. This parameter was found to exhibit a linear relationship with the Young's modulus. The Young's modulus correlated more with Ψ_c than the uncompensated characteristic parameter (Ψ) modeled for carbon black. The wear rate and volume loss measured using a blade-type abrader and Akron abrader were respectively observed to be inversely proportional to Ψ_c, that is, the wear resistance of Silica/SBR compound improved as the particle size became smaller and the silica structure became intricate. The coefficient of determination (R²) obtained from the linear relationship between Ψ_c and wear rate was higher than those between Ψ_c and volume loss for the Silica/SBR compound. Thus, the blade-type abrader exhibited high potential to be used for accurately evaluating the effect of particle size and structural properties of silica on the wear behavior of SBR compounds.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.251-251
• /
• 2009

The generation of energy and the cooling of system using thermoelectric semiconductor material have been in spotlight. Thermoelectric effect increases with the decrease of the thermal conductivity. In the thermoelectric devices, thermal conductivity is related to phonon scattering. Therefore, few studies have been conducted in the thermoelectric materials dispersed nano oxide particle for increasing the phonon scattering. However, core-shell structure which nano particle disperses in solvents and then which thermoelectric materials coated on the nano oxide particles has not been reported. In this study, we selected commercial nano powder such as $Al_2O_3$. This nano particle was about 20nm and was crushed aggregate by mechanical treatment. We have developed the effect of the dispersant and the solvent. The properties of particles were evaluated by SEM, TEM, particle size analysis, and BET. Dispersion and dispersion stability were evaluated by electronic microscope and turbidity.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.3
• /
• pp.111-119
• /
• 2014

A novel pulsed laser ablation process in liquid was investigated to prepare scheelite-type ceramic [calcium tungstate ($CaWO_4$) and calcium molybdate ($CaMoO_4$)] nanocolloidal particles. The crystalline phase, particle morphology, particle size distribution, absorbance and optical band-gap were investigated. Stable colloidal suspensions consisting of well-dispersed $CaWO_4$ and $CaMoO_4$ nanoparticles with narrow size distribution could be obtained without any surfactant. Particle tracking analysis using optical microscope combined with image analysis was applied for a fast determination of particle size distribution in the prepared nanocolloidal suspensions. The mean nanoparticle size of $CaWO_4$ and $CaMoO_4$ colloidal nanoparticles were 16 nm and 30 nm, with the standard deviations of 2.1 and 5.2 nm, respectively. The optical absorption edges showed blue-shifted values about 60~70 nm than those of reported in bulk crystals. And also, the estimated optical energy band-gaps of $CaWO_4$ and $CaMoO_4$ colloidal particles were 5.2 and 4.7 eV. The observed band-gap widening and blue-shift of the optical absorbance could be ascribed to the quantum confinement effect due to the very small size of the $CaWO_4$ and $CaMoO_4$ nanocolloidal particles prepared by pulsed laser ablation in liquid.

• Nuclear Engineering and Technology
• /
• v.34 no.1
• /
• pp.60-67
• /
• 2002

The effects of ball-milling time(0 ~4 hrs) have been investigated on the change of powder characteristics, compaction behavior (compaction pressure range : 200 ~400MPa) and sinterability (1700'c in Ha atmosphere) of two different UO$_2$ powders (ex-ADU and ex-AUC) prepared by the wet process. It is observed that, while the ex-ADU UO$_2$ was little affected, the ex-AUC UO$_2$ was largely affected by the ball-milling treatment. This may be attributed to the characteristics of particle size formed during the preparation step, i.e.., the former has a small average size of about 1.0${\mu}{\textrm}{m}$, while the latter has a relatively large average size of about 301n. It appeared that the effective size reduction by ball-milling treatment is limited to the particle size larger than l${\mu}{\textrm}{m}$, and to the extent of maximum decrease in size of about 0.5tn. In the case of ex-AUC UO$_2$, it is observed that the particle size decreased with ball-milling time and green density and sintered density of the pellets prepared from ball-milled powder increased compared with those of pellets prepared from the as-received powder under the same conditions. This may be attributed mainly to the fine particles formed during the ball-milling treatment.