• 한국분무공학회지
• /
• 제3권1호
• /
• pp.34-42
• /
• 1998

The correlation between the droplets size and the velocity are investigated for an intermittent spray of the pintle type fuel injector employed in a port injection gasoline engine. The analysis such as the mean droplet size, SMD, and velocity under the fixed injection period and varied fuel pressures are conducted utilizing PDPA systems. As results, the experimental data obtained, show that the larger droplet sizes. the higher velocities during the spray tip arrival time, and that at Z=70mm, r=8mm, both droplet sizes and velocities are peak. At the upstream, flow of droplets are dominated by injection pressure, which are more effected inertia force of droplets at the downstream of Z=70mm.

• 한국자동차공학회논문집
• /
• 제13권6호
• /
• pp.7-12
• /
• 2005

In order to analyze the microscopic spray characteristics of free spray in ultra high pressure region, the droplets size and velocity of free spray injected under atmosphere condition were measured by PDPA. As injection pressure became ultra high pressure, the droplets size was decreased continuously due to the increase of mutual reaction between droplets and air. But the decreasing rate became moderate. The velocity was increased until 250 MPa, and then decreased over that of injection pressure. It was seemed that the droplet size was similar in range of $280\~350\;MPa$, but increased in 414 MPa, even though injection pressure was increased. The microscopic spray characteristics of free spray got worse in 414 MPa.

• 한국재료학회지
• /
• 제27권2호
• /
• pp.100-106
• /
• 2017

Nanosized and aggregated $Y_2O_3:Eu$ Red phosphors were prepared by template method from metal salt impregnated into crystalline cellulose. The particle size and photoluminescent property of $Y_2O_3:Eu$ red phosphors were controlled by variation of the calcination temperature and time. Dispersed nanosol was also obtained from the aggregated $Y_2O_3:Eu$ Red phosphor under bead mill wet process. The dispersion property of the $Y_2O_3:Eu$ nanosol was optimized by controlling the bead size, bead content ratio and milling time. The median particle size ($D_{50}$) of $Y_2O_3:Eu$ nanosol was found to be around 100 nm, and to be below 90 nm after centrifuging. In spite of the low photoluminescent properties of $Y_2O_3:Eu$ nanosol, it was observed that the photoluminescent property recovered after re-calcination. The dispersion and photoluminescent properties of $Y_2O_3:Eu$ nanosol were investigated using a particle size analyzer, FE-SEM, and a fluorescence spectrometer.

• 한국재료학회지
• /
• 제25권6호
• /
• pp.274-278
• /
• 2015

The possibility of using the chemical precipitation method of up-cycled ammonium paratungstate (APT) was studied and compared with the thermal decomposition method. $WO_3$ particles were synthesized by chemical precipitation method using a 1:2 weight ratio of APT: Di-water. For thermal decomposition, APT powder was heated for 4h at $600^{\circ}C$ in air atmosphere. The reaction products were characterized by X-ray diffraction (XRD), X-ray fluorescence spectrometer (XRF), particle size analyzer (PSA), and field emission-scanning electron microscopy (FE-SEM). Thermogravimetric analysis (TGA) of the up-cycled APT allowed for the identification of the sequence of decomposition and reduction reactions that occurred during the heat treatment. TGA data indicated a total weight loss of 10.78% with the reactions completed in $658^{\circ}C$. The XRD results showed that APT completely decomposed to $WO_3$ by thermal decomposition and chemical precipitation. The particle size of the synthesized $WO_3$ powders by thermal decomposition with 2 h of planetary milling was around $2{\mu}m$ During the chemical precipitation process, the particle size of the synthesized $WO_3$ powders showed a round-shape with ${\sim}0.6{\mu}m$ size.

• Korean Chemical Engineering Research
• /
• 제51권5호
• /
• pp.628-633
• /
• 2013

토너 입자 내부의 카본블랙의 분산성이 우수한 스타이렌 기반 현탁중합토너를 제조하기 위하여 카본블랙의 표면을 개질하였다. 산화반응을 통해 카본블랙 표면에 도입된 히드록시기와 유기산(올레산, 팔미트산, 아크릴산)의 카르복시기 사이의 에스터화 반응을 통해 표면이 유기화 개질된 카본블랙을 제조하였다. 카본블랙의 표면개질을 확인하기 위하여 FTIR을 이용하였다. 바인더 수지 모노머 혼합물에 대한 카본블랙의 가시적인 분산성 실험을 진행하였으며 입도분석기를 이용해 분산된 카본블랙의 입자 크기를 측정하였다. 광학현미경 사진을 분석한 결과 표면이 올레산으로 개질된 카본블랙을 사용할 경우 토너 입자 내부의 카본블랙의 분산성이 크게 향상되었다. 올레산으로 개질된 카본블랙을 이용해 제조한 중합토너는 입경 및 입경분포도 토너로서 이상적이었다.

• 정보저장시스템학회:학술대회논문집
• /
• 정보저장시스템학회 2005년도 추계학술대회 논문집
• /
• pp.75-80
• /
• 2005

Study for toner adhesion is known as an important role in electrophotography. In this research, a centrifugal detachment method was used to measure the adhesion force of several hundred particles simultaneously and to determine its sensitivity to particle size. For uncharged toner particles, we estimated the van der Waals force based on the centrifugal farce experiments. Then for charged toner particles, the centrifugal force experiments were carried out. The difference between the results for charged toner particles and the results for uncharged toner particles was compared with the image force calculated from a model which assumed that the toner charge was located at the center of the particle. In the calculations, experimental data obtained by E-SPART (Electrical- Single Particle Aerodynamic Relaxation Time) analyzer were used. The adhesion force of micro-sized toner particles deposited on the DR surface was found to be approximately 1${\~}$3 nN.

• 정보저장시스템학회논문집
• /
• 제2권2호
• /
• pp.105-110
• /
• 2006

Study for toner adhesion is 3non as an important role in electrophotography. In this research, a centrifugal detachment method was used to measure the adhesion force of several hundred particles simultaneously and to determine its sensitivity to particle size. For uncharged toner particles, we estimated the van der Waals force based on the centrifugal force experiments. Then for charged toner particles, the centrifugal force experiments were carried out. The difference between the results for charged toner particles and the results for uncharged toner particles was compared with the image force calculated from a model which assumed that the toner charge was located at the center of the particle. In the calculations, experimental data obtained by E-SPART (Electrical-Single Particle Aerodynamic Relaxation Time) analyzer were used. The adhesion force of micro-sized toner particles deposited on the DR surface was found to be approximately $1{\sim}3$ nN.

• 한국수소및신에너지학회논문집
• /
• 제28권3호
• /
• pp.300-307
• /
• 2017

This study is to investigate particle size and velocity profile of gasoline port injector using Phase Doppler Particle Analyzer (PDPA). In this experiment, a GV 250 Delphi port injector used for motorcycles was used for liquid injection. The injector consists of four holes and has a static flow rate of 2.13 g/s. The fuel used in the injection was N-heptane, which is similar to gasoline, as an alternative fuel. The test fuel was injected at an atmospheric temperature of $20^{\circ}C$ and an open atmosphere of 1 atm. The injection time was 10 ms and the injection pressure was 3.5 bar in PDPA experiment. The experimental target position was fiexd at 30, 50 and 75 mm from the nozzle tip and data were collected for a total of 10,000 samples. The experimental results show that the length diameter (D10), the Sauter mean diameter ($D_{32}$), and the mean droplet velocity (MDV) are $45-54{\mu}m$, $99-115{\mu}m$ and 15-21 m/s, respectively.

• 폴리머
• /
• 제29권1호
• /
• pp.8-13
• /
• 2005

상변환 물질(PCM)을 함유하는 폴리스티렌(PS) 입자는 미니에멀션 중합을 이용하여 제조하였고, 여러 제조 조건에 따라 제조된 고분자 라텍스는 평균 입자크기, 입자 분포 그리고 잠열 저장특성에 관하여 조사하였다. 제조된 PS 입자의 형태와 입자 특성은 각각 SEM과 입도 분석기에 의하여 측정하였다. 분석 결과, 생성된 라텍스 입자의 특성은 각 변수에 의하여 조절할 수 있었으며, 제조된 PS 입자는 나노크기의 안정한 구형의 입자가 생성되는 것을 관찰할 수 있었다. 이는 중합시 첨가된 공유화제는 단량체 입자간의 Oswald ripening과 유착을 억제시키기 때문인 것으로 판단된다. 또한 PCM을 함유하는 PS 입자의 열적 특성은 시차주사열량계(DSC)를 이용하였고, PS 입자의 용융-동결 싸이클에 의하여 열에너지 저장 및 방출 특성을 조사하였다. DSC 결과로부터, PCM을 함유하는 PS 입자의 최대 잠열량은 약 145 J/g으로 나타나는 것을 확인할 수 있었고, 이로부터 PCM을 함유하는 PS 입자는 열에너지 저장매체로서 우수한 잠재성을 갖는 것으로 판단된다.

• 융합정보논문지
• /
• 제10권12호
• /
• pp.236-244
• /
• 2020

본 연구에서는 하천실험센터에서 부유 물질 실험을 수행하여 부유 물질의 거동 및 확산을 관찰하고 이를 입자분산모형을 통하여 그 이동을 구현하고자 하였다. 규사를 물과 믹서기를 이용하여 혼합한 후 실규모 크기의 실험수로에 인위적으로 투입하고 레이저부유사측정기(LISST)를 이용하여 부유 물질의 농도를 측정하였다. 실험에서 드론 이미지 및 부유사 측정기 관측 데이터와 입자 분산 모형을 통해 부유 물질의 거동을 모의하여 비교한 결과, 비교적 실험 결과가 구현이 잘 된 것을 확인할 수 있었다. 이를 통하여 입자 분산 모형의 적용성은 물론, 높은 강우량으로 인한 유량 발생 시 부유 물질 예측 활용성을 기대할 수 있게 되었다.