• 터널과지하공간
• /
• 제29권3호
• /
• pp.148-156
• /
• 2019

최근 도심지에서의 터널 및 지하공간 개발에 있어 TBM을 비롯한 다양한 형태의 기계식 굴착장비의 적용이 증가하고 있다. 한편 기존의 전통적인 암석절삭방식에서 변형된 언더커팅방식 적용한 암반의 기계식 굴착공법에 대한 연구가 선진국을 중심으로 수행되어 소개된 바 있다. 따라서 국내에서도 기존의 암반기계굴착에 대한 연구를 지속적으로 수행함과 동시에 최신 기술에 대한 연구가 요구된다. 본 연구에서는 언더커팅에 대한 기초연구로서 해당 기술의 원리 및 굴착방식에 대한 소개와 더불어 해외 선진 기관들의 연구 현황을 조사하였다. 언더커팅공법은 터널 및 지하공간의 개발을 위한 단독공법으로 적용이 가능할 뿐만 아니라 터널의 확공 및 기존 공간의 확장을 위한 보조공법으로의 활용성도 우수한 것으로 판단되었다.

• Asian-Australasian Journal of Animal Sciences
• /
• 제15권2호
• /
• pp.279-282
• /
• 2002

Twenty six male Hanwoo (Korean cattle) carcasses were measured for pH, temperature and instrumental color changes of loins during 24 h post-mortem carcass chilling at $4^{\circ}C$ in the cooler. The average internal temperature of loins was about $5^{\circ}C$ after 24 h of chilling, and with the exclusion of those with an ultimate pH>6.0 (dark-cutters), the average pH value was 5.5. When all carcasses were considered for the partial correlation coefficient between color and pH, with the temperature effect excluded, CIE $L^*$, $a^*$ and $b^*$ seemed to be affected significantly by pH during chilling process (p<0.001). However, when carcasses with dark-cutting condition were excluded, the correlation coefficients were much lower. In contrast, when the partial correlation coefficients between color and temperature, excluding the effect of pH on them, were analyzed, the relationship between color and temperature did not change much after values of DFD (dark, firm, dry) beef were excluded. The results suggested that the known interrelationship of color and pH in chilled beef loins be mainly due to the influence of temperature on pH and color.

• 한국표면공학회지
• /
• 제15권3호
• /
• pp.138-145
• /
• 1982

The effects of the simultaneous variations of the ratio of feed gases(H2/N2 Flow ratio), feed gas flow rate (H2/N2, total-flow rate) and partial pressures of TiCl4 (PTiCl41) as well as deposition time and cobalt content of the substrate on the deposition rate of the TiN Coated Cemented Tungsten Carbide Tools were investigated. Deposition was carried out in the temperature range of 930$^{\circ}C$-1080$^{\circ}C$ and an activation energy of 46.5 Kcal/mole can be calculated. Transverse rupture strength was noticeably reduced by the TiN coating on the virgin surfa-ce of Cemented Tungsten Carbide, the extent of which was decreased according to the coa-ting thickness. Microhardness value observed on the work was in the range of 1700∼2000kg/mm, which were in well agreement with the value of bult TiN. The wear resistance of TiN layers was performed by turning test and it was observed that crater and flank resistance remarkably enhanced by TiN coating.

• 한국정밀공학회지
• /
• 제17권4호
• /
• pp.114-120
• /
• 2000

Burr is an unavoidable and undesirable by-product of most metal cutting or shearing operations. This burr must be removed to improve the fit of machined parts and safety of workers, to improve the effectiveness of finishing operations. Despite the full or partial automation of FMC or FMS, deburring operations to obtain workpiece with fine surface quality are difficult to be automated since the occurrence and condition of burr are not constant. This study focused on developing a software for deburring automation, which includes automatic recognition of parts, generation of deburring tool path and NC code, by analyzing the IGES format file which contains information of part geometry. The successful performance of developed software was demonstrated by computer simulation and deburring experiment using miniature end brush. And, this research can provide a basis for further advanced studies for automated deburring applications.

• 대한치과의사협회지
• /
• 제51권6호
• /
• pp.337-345
• /
• 2013

Currently CAD/CAM technology has been used widely in dentistry. But it has mainly been focused on fabrication of fixed partial dentures and implant-supported prosthesis. DENTCA company uses new cutting edge of CAD/CAM technology to revolutionize denture production. With developing a CAD/CAM technology of DENTCA company, it is possible to make complete dentures with minimum visits to the clinic. The aim of this article is to introduce a new denture-making method by CAD/CAM.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.18-21
• /
• 2002

As the mask design rules get smaller, the probability of the process failure becomes higher due to the narrow overlay margin between the contact and metal interconnect layers. To obtain the minimum process margin, a tabbing and cutting method is applied with the rule based optical proximity correction to the metal layer, so that the protection to bridge problems caused by the insufficient space margin between the metal layers can be accomplished. The side-lobe phenomenon from the attenuated phase shift mask with the tight design nile is analyzed through the aerial image simulation for test patterns with variation of the process parameters such as numerical aperture, transmission rate, and partial coherence. The corrected patterns are finally generated by the rules extracted from the side-lobe simulation.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 하계종합학술대회 논문집(2)
• /
• pp.209-212
• /
• 2002

As the mask design rules get smaller, the probability of the process failure becomes higher doc to the narrow overlay margin between the contact and metal interconnect layers. To obtain the minimum process margin, a tabbing and cutting method Is applied with the rule based optical\ulcorner proximity correction to the metal layer, so that the protection to bridge problems caused by the insufficient space margin between the metal layers can be accomplished. The side-lobe phenomenon from the attenuated phase shift mask with the tight design rule is analyzed through the aerial image simulation for test patterns with variation of the process parameters such as numerical aperture, transmission rate, and partial coherence. The corrected patterns are finally generated by the rules extracted from the side-lobe simulation.

• 한국정밀공학회지
• /
• 제18권11호
• /
• pp.155-160
• /
• 2001

To achieve high precision cutting as well as production capability in the machine tool, it is needed to develop excellent rigidity statically, dynamically and thermally as well. In order to predict the qualitative behavior of a machine tool, simultaneous analysis of mechanics and heat transfer is required. Generally, machine tool designers have solved designing problems based on partial estimation of the specified rigidity. This study clears the inter-relationship between therm, and propose multi-phase optimization of machine tool structure using a genetic algorithm. The multi-phase solution method is consists of a series of mechanical design problem. At this first phase of static design problem, multi-objective optimization for the purpose of minimization of the total weight and static compliance minimization is solved using the Pareto Genetic Algorithm.

• 한국표면공학회지
• /
• 제27권3호
• /
• pp.143-148
• /
• 1994

Effects of process variables of HCD ion plating on the film composition of Ti(C, N) were analyzed. The mole ratio of carbon to nitrogen and that of non-metal to titanium in the film primarily depend on the partial pressure ratio of ($C-2H_2$/ $N_2$) and total reactive gas pressure, respectively. The amount of nonmetallic com-ponents increases in nonlinear fashion as the total gas pressure due to the different reactivity of $C-2H_2$ and $N_2$ gases with Ti. The nonmetallic components was saturated dwith nitrogen when the nitrogen gas was more than 60% of total reactive gas. These two process variables could be related systematically using the concept of effective pressure in which the difference of reactivity of each gas was normalized.

• 한국정밀공학회지
• /
• 제15권11호
• /
• pp.76-82
• /
• 1998

In this study, the Ball screw and Servo motor Mechanism is considered as a High Speed Tool Feed System for the machining of a piston of a reciprocating engine. For the machining of a piston, that shapes oval, high speed servo mechanism is needed as a positioning of a cutting tool, and the stroke of tool is 0.1 mm ~ 1 mm. Ball screw and servo motor Mechanism is available very much because this mechanism is used widely in general machine. This Mechanism has been designed with the use of the decrease in mass and partial wear of the ball screw for high speed positioning of tool. Also the periodic learning control method with the inverse transfer function compensation has been applied to the positioning control for the high accuracy positioning of tool. These applications lead the achievement of the machining of a piston with an accuracy of 5${\mu}{\textrm}{m}$ at 2500 rpm in CNC turning.