• Journal of the Ergonomics Society of Korea
• /
• v.21 no.2
• /
• pp.59-70
• /
• 2002

This paper is about the evaluation of stress response and recovery using biosignals and fuzzy theory. We caused mental stress by means of a coin-stacking task. During the experiment, 4 kinds of biosignals, including frontalis EMG, ECG, peripheral skin temperature and skin conductance level, were acquired. Then, the degree of stress was assessed by synthetically those signals using fuzzy inference. From the fuzzy inference result, the parameters (amount of physiological change / amount of imposed stress) and (time to 25% recovery), which represent response and recovery respectively, were derived. We made a two-dimensional point graph using the response parameter as an abscissa and the recovery parameter as an ordinate for each subject.

• Journal of Welding and Joining
• /
• v.26 no.2
• /
• pp.69-74
• /
• 2008

590MPa grade weldable steels were gas metal arc welded with flux cored wires. Welding parameters such as current, voltage, and speed were varied independently. Effects of each parameter on the strength and chemical composition of weld metal were investigated. Increase of voltage caused decrease of weld metal tensile strength due to the low recovery of alloying elements such as carbon and manganese. On the contrary, increase of current and speed resulted in increase of weld metal strength because of higher recovery of the alloying elements.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.4
• /
• pp.787-798
• /
• 2013

This paper proposes a special power circuit topology and its corresponding control strategy for an energy recovery power accumulator battery pack testing system (PABPTS), which is particularly used in electric vehicles. Firstly, operation principle and related parameter design for the system are illustrated. Secondly, control strategy of the composite power converter for PABPTS is analyzed in detail. The improved scheme includes a high accuracy charge and discharge current closed loop. active power reference for the grid-side inverter is provided by the result of multiplication between battery pack terminal voltage and test current. Simulation and experimental results demonstrate that the proposed scheme could not only satisfy the requirements for PABPTS with wide-range current test, but also could recover the discharging energy to the power grid with high efficiency.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1442-1447
• /
• 2004

A significant amount of labor hour is being spent for clean up spent abrasives after blasting. So, for improving the efficiency of abrasive(grit) recovery process which acts as the neck of a battle in preceding coating stage, it was established the theoretical background for pneumatic transport technology in the abrasive recovery system as well as experimentally evaluated the effect of design parameters such as flow pattern, saltation velocity and pressure drop on the efficiency of the abrasive recovery system. And, by optimizing the operating parameter such as the length and diameter of suction hose, specification of recovery device, recovery mouth and hose connection method, a method which can dramatical1y increase the efficiency of abrasive recovery system, is derived.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.65 no.3
• /
• pp.178-182
• /
• 2016

FIDVR(Fault Induced Delayed Voltage Recovery) is a phenomenon that recovery of the system voltage level delays after the fault. Cause of FIDVR phenomenon is motor load characteristic about voltage and reactive power. In low voltage condition, the motor go to stall state that consume large amount of reactive power. As a result, the voltage recovery problem is that of repeated occurrences of sustained low voltage following faults on the system. In this paper, analysis the characteristics of the motor load. And using the korean power system actual data, perform a case studies to voltage delay recovery phenomenon alleviation method. Change of each parameters by analyzing the effect on system and selecting an influence parameter. In addition, dynamic characteristic analysis of the resulting difference in the proportion by the motor load in power systems, considering the effect on the voltage stability.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.5A
• /
• pp.634-640
• /
• 2000

This paper proposes a new extended decision directed-decision estimated phase recovery algorithm based on maximum likelihood parameter estimation for OQPSK. In this scheme, comparing conventional one, the data dependent noise of phase recovery loop is reduced by inserting filter with 2 taps to in-phase and quadrature-phase channel respectively before phase detector. The proposed scheme is compared to conventionalscheme and OQPSK in aspect to BER(Bit Error Rate) and phase error according to the roll-off factor of baseband filter, the output back-offs of nonlinear satellite channel, and loop bandwidth.

• Proceedings of the KSRS Conference
• /
• 2004.10a
• /
• pp.642-645
• /
• 2004

This paper focuses on recovering systematic biases during LIDAR calibration, particularly using natural surfaces as control features. Many previous approaches have utilized all the points overlapping with the control features and often experienced with an inaccurate value converged with a poor rate due to wrong correspondence in pairing a point and the corresponding control features. To overcome these shortcomings, we establish a preventive scheme to select the pairs of high confidence, where the confidence value is based on the error budget associated with the point measurement and the linearity and roughness of the control feature. This approach was then applied to calibraring the LIDAR data simulated with the given systematic biases. The parameters were successfully recovered using the proposed approach with the accuracy and convergence rate superior to those using the previous approaches.

• The Korean Journal of Ecology
• /
• v.23 no.6
• /
• pp.435-438
• /
• 2000

Diameter distributions describe forest stand structure information. Prediction equations for percentiles of diameter distribution and parameter recovery procedures for the Weibull distribution function based on four percentile equations were applied to develop prediction system of even-aged slash pine stand structure development in terms of the number of stems per diameter class changes. Four percentiles of the cumulative diameter distribution were predicted as a function of stand characteristics. The predicted diameter distributions were tested against the observed diameter distributions using the Kolmogorov-Smirnov two sample test at the ${\alpha}$=0.05 level. Statistically, no significant differences were detected based on the data from 236 evaluation data sets. This stand level diameter distribution prediction system will be useful in slash pine stand structure modeling and in updating forest inventories for the long-term forest management planning.

• 대한정형외과스포츠의학회:학술대회논문집
• /
• 2004.09a
• /
• pp.6-6
• /
• 2004

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.245-248
• /
• 2008

This paper deals with the parameter study of roller leveling process of steel cord using finite element analysis. A simplified model of roller leveling process is constructed for the efficient numerical simulation considering the computing time. Using the constructed simulation scheme, the parameter study of main process parameters, such as back-tension and intermesh, is carried out in order to evaluate elastic recovery angle and roller force quantitatively. The effect of the initial shape of steel cord is also evaluated during the parameter study. And the mechanism of roller leveling process is verified by investigating the residual stress distribution.