• Journal of the Korean Wood Science and Technology
• /
• 제40권4호
• /
• pp.287-293
• /
• 2012

본 연구에서는 현재 국내 목조건축에서 벽구성 재료로 많이 사용되고 있는 수입 OSB(배향성 스트랜드보드)를 국산 합판으로 대체하기 위해 OSB와 국산 합판의 못 접합부 전단성능을 비교 검토하였다. 주부재(잣나무)와 측면부재(OSB 합판)의 섬유 방향성(평행 직각)에 따른 전단성능은 합판에서 현저하였다. 결과, OSB와 합판 모두 현행 국내 기준인 못 접합부 기준 허용전단내력을 만족하는 것으로 나타났다. 그리고, 표면층에 MLH(열대산 활잡목)를 사용하고 7ply 구성한 합판(P-4 type)은 OSB보다 섬유방향에 관계없이 큰 전단성능을 나타냈다. 전반적으로 측면부재로서 합판을 사용할 경우 주부재에 대하여 섬유방향을 직교되도록 구성할 경우, 평행방향 구성보다 큰 전단성능을 발휘할 수 있음이 확인되었다.

• Journal of the Korean Wood Science and Technology
• /
• 제47권1호
• /
• pp.40-50
• /
• 2019

The aim of this study was to investigate the effects of density, temperature, size, and grain direction on measurement of moisture contents (MC) of wood materials non-destructively. The MC of different sizes of solid wood, glulam, and CLT from larch (larix kaempferi, $560kg/m^3$) and pine (pinus koraiensis, $430kg/m^3$) were measured using the dielectric type and resistance type meters. The specimens were conditioned in the environmental chamber to be equilibrium moisture content (EMC) of 12 % and 19 %. When density setting in dielectric type meter was increased from $400kg/m^3$ to $600kg/m^3$, the MCs of specimen (S-L-100-E) were decreased from 13.4 % to 11.3 %. However, when wood group (WG) setting in resistance type meter was changed from WG1 to WG4, the measured MCs were increased from 9.2 % to 12.3 %. When temperature setting in resistance type meters was changed from 0 to $35^{\circ}C$, the MC was decreased from 17.0 % to 13.0 %. The MCs measured by dielectric type meter for larger specimens (S-L-100-E_11.3 %, G-L-240-E_11.7 % and C-L-120-E_12.8 %) were higher than those of small size specimens (S-L-30-E_8.7 %, G-L-150-E_10.3 %, and C-L-90-E_9.7 %). The MCs measured by resistance type meter for larger specimens (G-L-240-E_11.6 % and C-L-120-E_13.3 %) were also higher than those of small size specimens (G-L-150-E_10.4 %, and C-L-90-E_11.8 %). The resistance type meter was not affected by the grain direction but the dielectric type meter were affected by the grain direction. The MC measured by resistance type meter for G-L-120-E perpendicular to grain direction was 11.5 % and the measured MC parallel to grain direction was 11.3 %. The MC measured by dielectric type meter parallel to grain direction (12.1 %) was higher than that measured perpendicular to grain direction (10.7 %).

• Journal of the Korean Wood Science and Technology
• /
• 제36권4호
• /
• pp.93-101
• /
• 2008

하중방향(섬유평행방향, 섬유직각방향)과 접합구(볼트, 드리프트 핀) 적층면방향(평행, 수직)에 따른 국내산 낙엽송집성재의 지압강도시험을 실시하였다. 지압시편은 5 ply의 집성재를 사용하였고, 접합구의 직경은 12, 16, 20 mm를 사용하였다. 시험결과는 다음과 같다. 1) 볼트와 드리프트 핀의 각 직경에 따른 평균최대지압강도는 섬유평행하중방향의 경우 비슷한 경향을 보였으며, 섬유평행하중방향의 평균최대지압강도가 섬유직교방향보다 1.50~2.31배 높게 나타났다. 평균지압강도의 경우 섬유평행하중방향시편은 직경 16 mm에서 20 mm로 증가할 때 20% 감소하였으며, 섬유직교방향은 뚜렷한 경향이 없었다. 2) 평균지압초기강성의 경우 섬유평행하중방향은 직경 16 mm일 때 가장 크게 나타났다. 드리프트 핀 접합부의 전단강도실험 시 초기강성과 평균지압초기강성은 직경이 증가할수록 비슷한 경향을 보였다. 3) 지압강도시험 시 섬유평행방향시편의 파괴형상은 직경이 작을수록 할렬파단을 보였다. 섬유직교방향의 시편은 대부분이 섬유평행방향으로 할렬파단이 일어났으며 볼트가 드리프트 핀 시편보다 더 많이 나타났다. 4) 지압강도예측식을 통해 구한 예측지압강도와 실제 5% 유사항복지압강도를 비교하였을 경우 섬유평행방향은 KBCS, NDS의 예측지압강도와 비슷하게 나타났으나, 섬유직교방향은 NDS에서 제안한 예측식이 잘 적용되는 것을 알 수 있었다.

• Journal of the Korean Wood Science and Technology
• /
• 제26권1호
• /
• pp.87-96
• /
• 1998

The bending performances were evaluated at the radiata pine plywood through veneer compositions encompassing veneer quality, ply-numbers and overlays of the high density- or medium density-phenol resin impregnated sheets (hereafter abbreviated as resin sheets) on the raw plywood. In addition, a prediction on the bending MOE of veneers and plywoods was carried out by the nondestructive testing with stresswave timer. The summarized results were as follows: I. Bending strength and bending MOE of resin sheets-overlaid plywoods in parallel surface grain direction through 5 and 7ply were increased by 13 to 45% and 17 to 34%, respectively. Resin sheets-overlay occurred an increasing effect of the strength efficiency i.e. strength perpendicular-to-grain direction versus that parallel-to-grain direction, showing the phenomenon that the plywood strength becomes greater at the perpendicular-to-grain direction of 7ply than at that of 5ply. Displacement at bending failure had a greater trend at 7ply than at 5ply, and was decreased by resin sheets-overlay. 2. After the nondestructive bending MOEs were measured for individual veneers, these veneers were rearranged in plywood-manufacture. In these plywoods, including resin sheets-overlay, the actual MOE was predictable with feasibility of $R^2$=0.53, and also the nondestructively-evaluated MOE was lower by 20% in raw plywood, and higher 20% in LVL than actual bending MOEs.

• Journal of the Korean Wood Science and Technology
• /
• 제50권1호
• /
• pp.1-11
• /
• 2022

To evaluate the bearing strength of red pine cross-laminated timber (CLT) with self-tapping screw (STS), which is widely used as a fastener for connection in CLT building, the bearing test was conducted. Accoring to the STS's diameters (8, 10, 12 mm), the bearing test specimens with half hole were manufactured. Bearing strength was compared and reviewed in consideration of the configuration in STS and the loading direction to the grain of red pine. As a result of the bearing test on the STS's diameter, the yield bearing load increases as the larger diameter of the STS in all directions of the red pine. The bearing strength of the thread part (thread + tip) was higher than the shank part (shank + shank cutter). In compared with the directions to the grain of red pine, the bearing strength of the cross section parallel to the loading direction was the highest, and the tangent section was the lowest bearing strength. The average bearing strength of the loading direction in parallel to the grain was 23.43 MPa, which was about 45% higher than the average 16.16 MPa in perpendicular to the grain. The predicted bearing strength calculated by Eurocode (EN) and Korean Building Code (KBC)'s equation was lower than the experimental value. It is nessesary to propose the new equations of bearing strength reflected the configuration information of STS.

• Journal of the Korean Wood Science and Technology
• /
• 제41권2호
• /
• pp.100-104
• /
• 2013

Bearing occurs by the rotations of members induced from horizontal or vertical load at traditional wooden joint in frame. The bearing between wooden members is not occurring at the whole surface of joint, but occurring only at the particular bearing area. In this study, partial bearing according to the different grain direction was evaluated. The partial compressive strength showed 3 times higher than pure compressive strength perpendicular to grain, 1.5 times higher than parallel to grain and 3.3 times higher than both of them. It is expected that this result can be very importantly applied when evaluating and analyzing the actual behavior of traditional wooden mortise and tenon joint.

• 한국재료학회지
• /
• 제4권4호
• /
• pp.439-444
• /
• 1994

분극처리된 PZT세라믹스에 외부응력을 인가하였을때 인가되는 응력의 방향에 따른 열화기구의 차이를 조사하였다. 그 결과 분극축과 수직으로 응력을 인가할때의 열화현상은 공간전하분극의 확산으로, 분극축과 평행하게 응력을 인가할때는 분역재배열현상으로 설명하였다. 소결체의 입자 크기가 커지면 열화폭이 커짐을 알 수 있었는데 이것은 입자크기에 따른 내부응력의 차이로 해석하였다.

• 한국안전학회지
• /
• 제33권1호
• /
• pp.1-6
• /
• 2018

The effects of the fiber direction, specimen size and temperature on the compressive strength of carbon fiber reinforced silicon carbide composite (C/SiC composite) manufactured by liquid silicon infiltration(LSI) is investigated. Tests were conducted in accordance with ASTM C 695 at room temperature and elevated temperatures. Experiments are conducted with two different specimens considering grain direction. With grain (W/G) specimens have a carbon fibers parallel to the load direction, but across grain (A/G) specimens have a perpendicular carbon fibers. To verify the specimen size effect of C/SiC composite, two types of specimens are manufactured. One has a one to two ratio of diameter to height and the other has a one to one ratio. The compressive strength of C/SiC composite increased as temperature rise. As specimens are larger, compressive strength of A/G specimens increased, however compressive strength of W/G decreased.

• 한국세라믹학회지
• /
• 제29권10호
• /
• pp.806-814
• /
• 1992

The aim of this study was to investigate the change in compressive strength, freacture behavior and degradation of piezoelectric properties with compressive cyclic loading in Pb(Zr, Ti)O3 of tetragonal, morphotropic phase boundary and rhombohedral composition. The highest compressive strength was found in rhombohedral composition. After poling treatment the strength increased by 8.4% and 6.5% in tetragonal and morphotropic phase boundary compositions respectively while changed little in rhombohedral. The increase of compressive strength after poling treatment is believed to be due to the internal stress around grain boundary by domain alginment toward electric field direction in the microstructures having tetragonality and the occurrence of domain switching to the direction perpendicular to electrical field during fracture. Fracture mode relatively change from transgranular to intergranular was observed in the large grain sized tetragonal and morphotropic phase boundary compositions before and after poling but the transgranular fracture mode always remained in the rhombohedral composition. From the X-ray diffractometer analysis the domains parallel to the electric field direction is known to undergo rearrangement during the cyclic loading into random direction that is responsible for the degradation of piezoelectric property.

• 한국세라믹학회지
• /
• 제32권10호
• /
• pp.1131-1138
• /
• 1995

Variations of piezoelectric properties and compressive strength of Sr-doped PZT ceramics were investigated with poling direction. The electro-mechanical coupling constants (k31 and k33) were increased linearly with increasing poling strength. The volume fraction of intergranular fracture also increased with incresing poling strength due to weakening of grain boundaries by domain rearrangement during poling process. The internal stresses induced from the poling at 2.5 kV/mm parallel and perpendicular to the poling direction poled were 405 MPa and 89 MPa, respectively. The compressive strength of the specimen poled parallel to the poling direction was higher than that perpendicular to the poling direction.