• Journal of Power Electronics
• /
• 제11권1호
• /
• pp.97-104
• /
• 2011

This paper proposes a new alternating current driving method for highly capacitive loads such as plasma display panels or piezoelectric actuators, etc. In the proposed scheme, a current balance transformer, which has two windings with the same turn-ratio, provides not only a resonance inductance for energy recovery but also a current balance among all of the switching devices of the driver for current stress reduction. The smaller conduction loss than conventional circuits occurs due to the dual conduction paths which are parallel each other in the current balance transformer. Also, the leakage inductances of the transformer are utilized as resonant inductors for energy recovery by the series resonance to the capacitive load. Furthermore, the resonance contributes to the small switching losses of the switching devices by soft-switching operation. To confirm the validity of the proposed circuit, prototype hardware with a 12-inch mercury-free flat fluorescent lamp is implemented. The experimental results are compared with a conventional energy-recovery circuit from the perspective of luminance performances.

• Journal of Power Electronics
• /
• 제13권4호
• /
• pp.592-599
• /
• 2013

This paper investigates a new isolated single-phase AC-DC converter, which integrates a modified AC-DC buck-boost converter with a DC-DC forward converter. The front semi-stage is operated in discontinuous conduction mode (DCM) to achieve an almost unity power factor and a low total harmonic distortion of the input current. The rear semi-stage is used for step-down voltage conversion and electrical isolation. The front semi-stage uses a coupled inductor with the same winding-turn in the primary and secondary sides, which is charged in series during the switch-on period and is discharged in parallel during the switch-off period. The discharging time can be shortened. In other words, the duty ratio can be extended. This semi-stage can be operated in a larger duty-ratio range than the conventional AC-DC buck-boost converter for DCM operation. Therefore, the proposed converter is suitable for universal input voltage (90~264 $V_{rms}$) and a wide output-power range. Moreover, the voltage stress on the DC-link capacitor is low. Finally, a prototype circuit is implemented to verify the performance of the proposed converter.

• E2M - 전기 전자와 첨단 소재
• /
• 제12권8호
• /
• pp.39-45
• /
• 1999

Comparative photoresponsive current-volt-age characteristics of n-channel PHEMT and MESFET on GaAs substrate. with (W/L)=200${\mu}{\textrm}{m}$/1${\mu}{\textrm}{m}$ of gates, are reported as a function of electro-optical stimulation (P\ulcorner, λ=830nm) for the first time as far as we know. Significantly different photoresponses are observed in MESFET and PHEMT, mainly due to different optoelectronic mechanisms in the formation and current conduction of channel carriers. Under high optical power, high photoresponsity with a strong non-linearity with P\ulcorner, predominantly due to a parallel conduction via a heavily doped Al\ulcornerGa\ulcornerAs donor layer, was observed in PHEMT while the optically induced drain current has been very small but monotonically increasing with optical stimulation in GaAs MESFET. We also investigated differences in optically stimulated gate leakage currents and photonic gate responses on gate voltage and drain voltage as a function of P\ulcorner. Based on the drain and gate responses to electro-optical stimulation. PHEMTs are expected to be a better candidate for high performance photonically responsive microwave device compared with MESFETs.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제48권8호
• /
• pp.448-454
• /
• 1999

This paper describes a new dc-ac inverter system which for achieving sinusoidal ac waveform makes use of parallel loaded high frequency resonant inverter consisting of full bridge. Each one of the pair of switches in the inverter is driven to synchronous output frequency and the other is driven to PWM signal with resonant frequency proportional to magnitude of sine wave. A forced discontinuous conduction mode is used to realize the quasi-sinusoidal pulse in each switching period. Therefore the inverter generates sinusoidal modulated output voltage including carrier frequency that is resonant frequency. Carrier frequency components of modulated output voltage is filtered by low pass filter. Since current through switches is always zero at its turn-on in the proposed inverter, low stress and low switching loss is achieved. Operating characteristics of the proposed system is analyzed in per unit system using computer simulation. The output voltage of if includes low harmonics and it is almost close to sine wave. Also, the theoretical analysis is proved through the experimental test.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 전력전자학술대회 논문집
• /
• pp.520-524
• /
• 2001

Recently, the demand of large capacity SMPS for industrial area is increasing. Full-bridge dc-dc converter with IGBT is most widely used for large capacity SMPS because IGBT has a low-conduction loss and large current capacity, But most large capacity Full-bridge do-dc converter using IGBT has low operating frequency because of switching loss at IGBT especially at turn-off by current tail and it's cause of relatively big converter size. MOSFET has low switching losses has been widely used for high frequency SMPS but it has a problem to apply to large capacity SMPS because it has large conduction resistance causing large on-time losses. In this paper, for reduction losses at switching device, MOSFET is applied at parallel with IGBT in full-bridge dc/dc converter.

• Journal of Electrical Engineering and Technology
• /
• 제10권1호
• /
• pp.216-226
• /
• 2015

The neutral beam injection generate ultra-high temperature energy in the tokamak of nuclear fusion. The neutral beam injection make up arc power supply, filament power supply and acceleration & deceleration power supply. The arc power supply has characteristics of low voltage and high current. Arc power supply generate arc through constant output of voltage and current. So this paper proposed suitable buck converter for low voltage and high current. The proposed buck converter used parallel switch because it can be increased capacity and decrease conduction loss. When an arc generated, the neutral beam injection chamber occur high voltage. And it will break output capacitor of buck converter. Therefore the output capacitor was removed in the proposed converter. Thus the proposed converter should be designed for the characteristics of low voltage and high current. Also, the arc power supply should be guaranteed for system stability. The proposed parallel buck converter enables the system stability of the divided low output voltage and high current. The proposed converter with constant output be the most important design of the output inductor. In this paper, designed arc power supply verified operation of system and stability through simulation and prototype. After it is applied to the 288[kW] arc power supply for neutral beam injection.

• 대한수학회논문집
• /
• 제33권3호
• /
• pp.1025-1037
• /
• 2018

We consider an ill-posed problem for the heat equation $u_{xx}=u_t$ in the quarter plane {x > 0, t > 0}. We propose a new method to compute the heat flux $h(t)=u_x(1,t)$ from the boundary temperature g(t) = u(1, t). The operator $g{\mapsto}h=Hg$ is unbounded in $L^2({\mathbb{R}})$, so we approximate h(t) by $h_{\delta}(t)=u_x(1+{\delta},\;t)$, ${\delta}{\rightarrow}0$. When noise is present, the data is $g_{\epsilon}$ leading to a corresponding heat $h_{{\delta},{\epsilon}}$. We obtain an estimate of the error ${\parallel}h-h_{{\delta},{\epsilon}}{\parallel}$, as well as the error when $h_{{\delta},{\epsilon}}$ is approximated by the trapezoidal rule. With an a priori choice rule ${\delta}={\delta}({\epsilon})$ and ${\tau}={\tau}({\epsilon})$, the step size of the trapezoidal rule, the main theorem gives the error of the heat flux as a function of noise level ${\epsilon}$. Numerical examples show that the proposed method is effective and stable.

• Journal of Power Electronics
• /
• 제16권5호
• /
• pp.1894-1903
• /
• 2016

In general, electrolytic capacitors are used to reduce power pulsations on PV-panels. However, this can reduce the reliability of the PV AC-module system, because electrolytic capacitors have a shorter lifetime than PV-panels. In addition, PV-panels generate irregular power and inject it into the grid because the output power of a PV-panel depends on the surrounding conditions such as irradiation and temperature. To solve these problems, a grid-connected photovoltaic (PV) AC-module with active power decoupling and energy storage is proposed. A parallel bi-directional converter is connected to the AC module to reduce the output power pulsations of PV-panels. Thus, the electrolytic capacitor can be replaced with a film capacitor. In addition, the irregular output power due to the surrounding conditions can be regulated by using a parallel energy storage circuit. To maintain the discontinuous conduction mode at low irradiation, the frequency control method is adopted. The design method of the proposed converter and the operation principles are introduced. An experimental prototype rated at 125W was built to verify the performance of the proposed converter.

• Journal of Power Electronics
• /
• 제10권1호
• /
• pp.9-13
• /
• 2010

This paper proposes an input-series-output-parallel connected ZVS full bridge converter with interleaved control for photovoltaic power conditioning systems (PV PCS). The input-series connection enables a fully modular power-system architecture, where low voltage and standard power modules can be connected in any combination at the input and/or at the output, to realize any given specifications. Further, the input-series connection enables the use of low-voltage MOSFETs that are optimized for a very low RDSON, thus, resulting in lower conduction losses. The system costs decrease due to the reduced current, and the volumes of the output filters due to the interleaving technique. A topology for a photovoltaic (PV) dc/dc converter that can dramatically reduce the power rating and increase the efficiency of a PV system by analyzing the PV module characteristics is proposed. The control scheme, consisting of an output voltage loop, a current loop and input voltage balancing loops, is proposed to achieve input voltage sharing and output current sharing. The total PV system is implemented for a 10-kW PV power conditioning system (PCS). This system has a dc/dc converter with a 3.6-kW power rating. It is only one-third of the total PV PCS power. A 3.6-kW prototype PV dc/dc converter is introduced to experimentally verify the proposed topology. In addition, experimental results show that the proposed topology exhibits good performance.

• Tribology and Lubricants
• /
• 제30권5호
• /
• pp.303-310
• /
• 2014

In order to reduce friction and improve reliability, researchers have applied various surface texturing methods to highly sliding machine elements such as mechanical seals and piston rings. Despite extensive theoretical research on surface texturing, previous numerical results are only applicable to isothermal and iso-viscous conditions. Because the lubricant flow pattern of textured bearing surfaces is much more complicated than that for non-textured bearings, the Navier?Stokes equation is more suitable than the Reynolds equation for the former. This study carries out a thermohydrodynamic (THD) lubrication analysis to investigate the lubrication characteristics of a single micro-dimpled parallel thrust bearing cell. The analysis involves using the continuity, Navier?Stokes, energy, temperature?viscosity relation, and heat conduction equations with the commercial computational fluid dynamics (CFD) code FLUENT. This study discretizes these equations using the finite volume method and solves them using the SIMPLE algorithm. The results include finding the streamlines, pressure and temperature distributions, and variations in the friction force and leakage for various dimple radii and depths. Increasing the dimple radius and decreasing the depth causes a recirculation flow to form because of a strong vortex, and the oil temperature greatly increases compared with the non-textured case. The present numerical scheme and results are applicable to THD analysis of various surface-textured sliding bearings and can lead to further study.