• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.371-372
• /
• 2007

The major causes of electrical fire are classified to short circuit fault, overload fault, electric leakage and electric contact failure. The occurrence factor of the fire is electric arc or spark accompanied with electrical faults. Residual Current Protective Device (RCD), that is Earth Leakage Circuit Breaker(ELB) and Molded_case Circuit Breaker (MCB), of high sensitivity type used at low voltage wiring cuts off earth leakage and overload, but the RCD can't cut off electric arc or spark to be a major factor of electrical fire. As the RCDs which are applied low voltage distribution panel are prescribed to rated breaking time about 30[ms] (KS C 4613), the RCDs can't perceive to the periodic electric arc or spark of more short wavelength level. To be improved on such problem, this research development is proposed to a auxiliary control apparatus for RCD trip on electric arc or spark due to electrical fire. Some experimental results of the proposed apparatus is confirmed to the validity of the analytical results.

• Industry Promotion Research
• /
• v.4 no.2
• /
• pp.1-8
• /
• 2019

This research is a technology for cutting the insulation of the busbar (busbar) installed in the distribution panel or switchboard, the results of the study, first, the cutting unit and frame of the cutting unit including a housing attached to the upper and lower cutters, respectively Busbar coating laser cutting machine is installed on the top, characterized by consisting of a stopper for adjusting the coating cutting distance of the busbar. Second, the frame is installed with the guide bar in the longitudinal direction at the top so as to be located at the rear side end of the table, the post is installed vertically at the front and rear at the upper middle part, respectively, and cut to the table at the outer side of the front post. It is characterized by the formation of holes. Third, the supporter is fixedly installed on the upper part of the guide bar arranged in the frame, and is characterized by consisting of a cylinder and a support plate. The meaning of this study is to prevent the safety accidents of workers, to improve the efficiency of cutting work, and to prevent the occurrence of scratches on the surface of the busbar.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.5
• /
• pp.547-556
• /
• 2019

Thinned, small larch logs have small diameters and no value-added final use, except as wood chips, pallets, or fuel wood, which are products with very low economic value; however, their mechanical strength is suitable for structural applications. In this study, small larch logs were sawed, dried, and cut into square timbers (with a $90mm{\times}90mm$ cross section) that were laterally glued to form core panels used to manufacture cross-laminated timber (CLT) wall panels. The surface and back of these core panels were covered with 12-mm-thick structural plywood panels, used as cross bands to obtain three-ply CLT wall panels. This attachment procedure was conducted in two different ways: gluing and pressing (CGCLT) or gluing and nailing (NGCLT). The size of the as-manufactured CLT panels was $1,220mm{\times}2,440mm$, the same as that of the plywood panels. The final wall panels were tested under lateral shear force in accordance with KS F 2154. As the lateral load resistance test required $2,440mm{\times}2,440mm$ specimens, two CLT wall panels had to be attached in parallel. In addition, the final CLT panels had tongued and grooved edges to allow parallel joints between adjacent pieces. For comparison, conventional light-frame timber shear walls and midply wall systems were also tested under the same conditions. Shear walls with edge nail spacing of 150 mm and 100 mm, the midply wall system, and the fabricated CGCLT and NGCLT wall panels exhibited maximum lateral resistances of 6.1 kN/m (100%), 9.7 kN/m (158%), 16.9 kN/m (274%), 29.6 kN/m (482%), and 35.8 kN/m (582%), respectively.

• Journal of IKEEE
• /
• v.23 no.1
• /
• pp.107-111
• /
• 2019

In FPD WET equipment, heaters are used a lot. There are many electric accidents caused by short circuit and overheating due to the use of heater, so it is necessary to have a safe electric system and interlock. Therefore, in this paper, we propose an electrical schematic and interlock for FPD WET equipment. In this paper, a hardware interlock such as a level sensor, an overheat protector, and an SSR heater sink is inserted, and the electric system is composed of ELB - MC - SSR - EOCR - heater. When the interlock occurs, the magnetic contactor (MC) is turned off and the power of the heater is cut off.EOCR, an electric overcurrent protection device, has an interlock to shut down the MC when there is an abnormality in the heater while checking the overcurrent, undercurrent and disconnection. These circuit configurations and interlocks are likely to be useful not only for WET equipment but also for any equipment in which the heater is placed.

• Journal of Korean Ophthalmic Optics Society
• /
• v.18 no.3
• /
• pp.231-239
• /
• 2013

Purpose: To design and fabricate the auto pattern maker for the development. Methods: we got the necessary data, needed in design, by using CAD. Based on the these data, we fabricated the trial product for the development of the auto pattern maker. Results: The auto pattern maker were composed with combinations of many elements; pattern making assembly, control panel, frame attachment and prober unit. The pattern making assembly was comprised of the cutter, the pattern holder, pattern remover and silence cover which could minimize the sound during the cutting process. The control panel was designed to be connected and operated with the main printed circuit board. The prober could get the eye shape data by scanning of 1.8 degrees around the groove of the frame through the encoding data according to the address. After starting, scanning was carried out in two passes, i.e. one right-handed and one left-handed. Communication connector could send the eye shape data from auto pattern maker to outer system with the RS232C transmission system. By using the one-way analysis of variance, we got the error rate of cut pattern size for ${\Phi}22mm$, ${\Phi}55mm$ and ${\Phi}62mm$. Because F-value was 0.510 and p-value was 0.601, no statistically significant differences were found. Also, the mean cutting error of the auto pattern maker was 0.0274 mm. Conclusions: we could succeed in making the trial product by applying it to the development of the auto pattern maker. The role of this auto pattern maker is to find a exact required size of lens to fit the frame by measuring the frame. The acquired data are transferred to outer system for grinding and finishing with patternless process. Also, the trial product can produce pattern to fit the frame. Therefore, it was confidently expected that the optometrists could handily produce pattern to fit the frame with this trial product and dispense the ophthalmic lens because of its efficiency and convenience compared to the past.

• Korean Journal of Optics and Photonics
• /
• v.13 no.4
• /
• pp.363-369
• /
• 2002

We have designed conductive transparent filters using a low-emissivity coating such as [dielectric|Ag|dielectric] for display applications. The design is the repetition of [$TiO_{2}$|Ti|Ag |$TiO_{2}$] to increase the transmittance in the visible and decrease the transmittance in the near IR. The conductive transparent filters are deposited by a radio frequency(RF) magnetron sputtering system. The optical, structural and electrical properties of the filters were investigated and the optical spectra are compared with simulated spectra. The thickness of the deposited Ag films is above 13 ㎚ to increase the conductivity and that of $TiO_{2}$ films is 24 ㎚ to increase the transmittance in the visible range. Ti blockers are employed to prevent the Ag films from being oxidized by an oxygen gas during the reactive sputtering process. Also, it is shown that the thicker Ti film is necessary as the period increases. Finally, a filter with repetition of the basic structure three times shows the better cut-off near infrared(NIR) and the sheet resistance as low as 2Ω/□ which is enough to shield an unnecessary electromagnetic waves for a display panel.

• Asian Pacific Journal of Cancer Prevention
• /
• v.15 no.16
• /
• pp.6881-6885
• /
• 2014

Background: The present study aimed to investigate the utility and importance of the various parameters of complete blood count panel for benign-malignant differentiation of adnexal masses. Materials and Methods: This retrospective study involved 316 patients with documented benign and 253 patients with malignant adnexal masses who underwent primary surgical treatment at a tertiary referral center. Prior to the study, all benign and malignant cases were compared within their own groups and then the benign and malignant cases were compared to each other. For all cases, cut-off, sensitivity, specificity, positive predictive value (PPV) and negative predictive value (NPV) were calculated for the neutrophil lymphocyte ratio (NLR), platelet lymphocyte ratio (PLR), neutrophil, lymphocyte, platelet and CA-125 parameters, and the results were compared in regards to the groups. Results: NLR, PLR, neutrophil, CA-125, and platelet values were higher in the malignant compared to the benign cases (p<0.01). The lymphocyte value was lower in the malignant cases (p<0.01). No significant differences were found for basophils and eosinophils (p > 0.05). For CA-125, the sensitivity, specificity, PPV and NPV for all cases were 78%, 62%, 62% and 78%, respectively. For NLR, they were 65.6%, 72.1%, 65.3%, and 72.3%, and for PLR, 48%, 81%, 67%, and 66%. Additionally, the sensitivity and specificity were 55% and 77% for CA-125, 66% and 58% for NLR, and 61% and 58% for PLR in early malignant cases. Conclusions: NLR and PLR appear to be useful methods that can be applied together with CA-125 due to the relatively high sensitivity values for the malign-benign differentiation of ovarian masses. Although the specificity of these parameters is lower than CA-125, especially in cases with early malignant ovarian pathology, their sensitivity being higher is promising for the early diagnosis of ovarian cancer. It can be used to detect ovarian malignancies in the early stages, and it will increase the treatment options and improve survival rates.

• Journal of the Korea Institute of Building Construction
• /
• v.14 no.2
• /
• pp.127-134
• /
• 2014

This study had the goal of analyzing the economic feasibility and constructability of a fire resistant curtain wall system using Light-weight Inorganic Composite Foam Board(LI-CFB). LI-CFBs, new materials with excellent fire resistance are being developed for use as the back panel of curtain wall and their fire resistance has already been analyzed through actual tests in earlier studies. In this study, a mock-up test involving the installation of the fire resistant curtain wall system on an actual building was conducted, and the system was compared with a common curtain wall system. This system is applied in the same way as a common curtain wall system. But the cutting LI-CFBs, which are brought from a factory, are used in the system and attached on the frame (mullion and transom). Even though the system requires more working time than the existing system, the LI-CFBs back panels are easy to cut and do not produce dust. Also, the panels are able to be assured the quality by checking damaged parts easily. Besides having a high level of fire resistance, the system's economic feasibility and constructability meets or exceeds those of the existing system.

• Tunnel and Underground Space
• /
• v.31 no.6
• /
• pp.534-548
• /
• 2021

In this paper, the feasibility of generating solar power near an abandoned quarry is examined with the objectives of resolving the essential problems that quarries encounter, such as rockfalls and space usage issues. On an abandoned quarry site in Sadang, Seoul, Republic of Korea, two different PV installation methods were analyzed. The first is attaching PV directly on the quarry slope. Since there are no corresponding safety standards and precedents for installing solar panels directly on slopes, the power generation potential was calculated by using topographic data and reasonable assumptions. The surface area of cut slope section was extracted from the Digital Elevation Model(DEM) via ArcGIS and Python programming to calculate the tilt and power capacity of installable panels. The other approach is installing PV as a rockfall barrier, and the power generation potential was analyzed with the assumption that the panel is installed in the direction of facing solar irradiation. For the derivation of power generation, the renewable energy generation analysis program SAM(System Advisor Model) was used for both methods. According to the result, quarries that have terminated resource extraction and remain devastated have the potential to be transformed into renewable energy generation sites.

• Journal of Animal Science and Technology
• /
• v.52 no.1
• /
• pp.37-42
• /
• 2010

A study was conducted to examine the effect of the castration time on growth, meat quality and fatty acid composition of Korean black goats. Forty five male kids were divided into five groups, including control (without castration) and four groups with the kids castrated at 0.5, 3, 5 and 7 months of age, respectively. Average daily body weight gain (ADG) for control was significantly (P<0.05) higher than the castrated groups. ADG did not differ between the castrated groups. The ADG of the male kids castrated at 3 and 5 months of age tended to be higher than the other castrated groups. Dressing percentage for 0.5 months-castrated group was higher than 7 months-castrated group. Retail cut percentages for control was higher (P<0.05) than others, but the retail cut percentages did not differ between the castrated groups. Compared with control, higher fat percentages of carcasses appeared in the castrated groups (P<0.05). The fat percentages gradually increased in earlier castrated animals. As castrated earlier, moisture contents tended to decrease, whereas crude protein and fat contents tended to increase. The different castration time did not affect physical properties of goat meat (shear force, cooking loss, and water holding capacity). Results from panel tests showed that juiciness or tenderness of meats for 5 months-castrated group tended to be higher than those for the other groups. The flavor of meatfor 7-months castrated group appeared to be more favorable compared with 0.5- or 3-months castrated groups (P<0.05). The proportion of saturated fatty acid in meat washigher for 5-months castrated group and lower for 3-months castrated group as compared to the other castrated groups, whereas the proportion of unsaturated fatty acid was vice versa (P<0.05). Mono-unsaturated fatty acid contents did not differ between thecastrated groups. Present results indicatedthat castration at 3 or 5 months of age increased growth performance and meat quality of Korean black goats.