• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.10a
• /
• pp.151-151
• /
• 2009

ZnO 박막은 큰 밴드 갭 및 가시광 영역에서 높은 광투과성을 가지며, 제조조건에 따라 비저항의 범위가 폭넓게 변화하므로 태양전지, 평판 디스플레이의 투명 전극뿐만 아니라 음향공전기, 바리스터 등에 이용되고 있다. ZnO 박막의 전도성을 향상시키기 위해서 일반적으로 Al, Ga, Ti, In, B, H(n-type), 등과 N, As(p-type)의 도펀트를 사용한다. 본 연구에서는 전기화학적인 방법을 사용하여 ITO/glass위에 ZnO film에 농도에 따른 Ga을 doping 하여 전기전도성 향상과 밴드갭을 넓힘으로서 전자의 recombination을 방지하여 유기태양전지의 효율을 높이는데 목적을 두었다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.11
• /
• pp.968-972
• /
• 2008

Ni/Ti/Al multilayer system ('/'denotes the deposition sequence) was tested for low-resistance ohmic contact formation to Al-implanted p-type 4H-SiC. Ni 30 nm / Ti 50 nm / Al 300 nm layers were sequentially deposited by e-beam evaporation on the 4H-SiC samples which were implanted with Al (norminal doping concentration = $4\times10^{19}cm^{-3}$) and then annealed at $1700^{\circ}C$ for dopant activation. Rapid thermal anneal (RTA) temperature for ohmic contact formation was varied in the range of $840\sim930^{\circ}C$. Specific contact resistances were extracted from the measured current vs. voltage (I-V) data of linear- and circular transfer length method (TLM) patterns. In constrast to Ni contact, Ni/Ti/Al contact shows perfectly linear I-V characteristics, and possesses much lower contact resistance of about $2\sim3\times10^{-4}\Omega{\cdot}cm^2$ even after low-temperature RTA at $840^{\circ}C$, which is about 2 orders of magnitude smaller than that of Ni contact. Therefore, it was shown that RTA temperature for ohmic contact formation can be lowered to at least $840^{\circ}C$ without significant compromise of contact resistance. X-ray diffraction (XRD) analysis indicated the existence of intermetallic compounds of Ni and Al as well as $NiSi_{1-x}$, but characteristic peaks of $Ti_{3}SiC_2$, a probable narrow-gap interfacial alloy responsible for low-resistance Ti/Al ohmic contact formation, were not detected. Therefore, Al in-diffusion into SiC surface region is considered to be the dominant mechanism of improvement in conduction behavior of Ni/Ti/Al contact.

• Current Photovoltaic Research
• /
• v.2 no.1
• /
• pp.1-7
• /
• 2014

We developed a method of growing thin Si film at $600^{\circ}C$ by hot wire CVD using a very thin large-grained poly-Si seed layer for thin-film Si solar cells. The seed layer was prepared by crystallizing an amorphous Si film by vapor-induced crystallization using $AlCl_3$ vapor. The average grain size of the p-type epitaxial Si layer was about $20{\mu}m$ and crystallographic defects in the epitaxial layer were mainly low-angle grain boundaries and coincident-site lattice boundaries, which are special boundaries with less electrical activity. Moreover, with a decreasing in-situ boron doping time, the mis-orientation angle between grain boundaries and in-grain defects in epitaxial Si decreased. Due to fewer defects, the epitaxial Si film was high quality evidenced from Raman and TEM analysis. The highest mobility of $360cm^2/V{\cdot}s$ was achieved by decreasing the in-situ boron doping time. The performance of our preliminary thin-film solar cells with a single-side HIT structure and $CoSi_2$ back contact was poor. However, the result showed that the epitaxial Si film has considerable potential for improved performance with a reduced boron doping concentration.

• Korean Journal of Materials Research
• /
• v.15 no.2
• /
• pp.89-92
• /
• 2005

The induction melting was employed to prepare Nb-doped $CoSb_3$ skutterudites and their thermoelectric properties were investigated. Single phase $\delta-CoSb_3$ was successfully obtained by induction melting and subsequent annealing at $400^{\circ}C$ for 2 hrs in vacuum. The positive signs of Seebeck coefficients for all the specimens revealed that Nb atoms acted as p-type dopants by substituting Co atoms. Electrical conductivity decreased and then increased with increasing temperature, indicating mixed conduction behavior. Electrical conductivity increased by Nb doping, and it was saturated at high temperature. Maximum value of the thermoelectric power factor was shifted to higher temperature with increasing the amount of Nb doping, mainly originated from the high Seebeck coefficient around mixed conduction temperature and high electrical conductivity.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.107-107
• /
• 2014

p형 자원 친화형 산화물 기반 능동형 층 성장에 대한 연구는 아직 개발 초기 단계이다. $Cu_2O$는 이러한 자원 친화형 저가 p형 산화물 중 하나로서 다양한 광학 응용분야에 있어 적용되고 있으며 특히 저가형 증착법인 전기증착법을 통해 형성시킨다면 가격 절감을 극대화 시킬 수 있다. 하지만 낮은 전도성으로 인해 전자소자에는 적용시키기 어렵다는 단점이 있기 때문에 본 연구팀은 5족 물질인 Antimony 를 $Cu_2O$의 p형 도펀트로 적용시켜 전기적 구조적 특성을 개선시키고자 하였다. 결과적으로 [111] 방향으로 높은 우선배향성을 갖고 전도성이 향상된 Sb-Cu2O 박막을 확인하였다.

• Journal of the Semiconductor & Display Technology
• /
• v.3 no.1
• /
• pp.35-39
• /
• 2004

Statistical design of experiments was successfully employed to investigate the effect of alternating magnetic field on activation of polycrystalline Si (p-Si) doped as n-type using $\textrm{PH}_3$, by full factorial design of three factors with two levels. In this design, the input variables are graphite size, alternating current, and activation time. The output parameter, sheet resistance, is analyzed in terms of the primary effects and multi-factor interactions. Notably, the three-factor interaction is calculated to be a dominant interaction. The interaction between graphite size and activation time and the main effect of current are important effects compared to the other variables and relevant interactions. Alternating magnetic flux activation is proved a significantly beneficial processing technique.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.346-349
• /
• 2009

We investigated the doping effects of $ReO_3$ in different p-type organic semiconductors on the formation of charge transfer complexes and the electrical conductivity by comparing the absorption in ultraviolet-visible-nearinfrared (UV-Vis-NIR) and the current density-voltage characteristics of the hole only devices, respectively. The large energy difference between the HOMO level of host and Fermi energy level of dopant (${\Delta}E$=$E_{HOHO,host}$ - $E_{F,dopant}$) gives higher concentration of CT complexes and enhanced conductivity.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.94-94
• /
• 2008

We have performed simulation for Junction Field Effect Transistor(JFET) using Silvco to improve its electrical properties. The device structure and process conditions of Si-control JFET(Si-JFET) were determined to set its cut off voltage and drain current(at Vg=0V) to -0.5V and $300{\mu}A$, respectively. From electrical property obtained at various implantation energy, dose, and drive-in conditions of p-gate doping, we found that the drive in time of p-type gate was the most determinant factor due to severe diffusion. Therefore we newly designed SiGe-JFET, in which SiGe layer is to epitaxial layers placed above and underneath of the Si-channel. The presence of SiGe layer lessen the p-type dopants (Boron) into the n-type Si channel the phenomenon would be able to enhance the structural consistency of p-n-p junction. The influence of SiGe layer will be discussed in conjunction with boron diffusion and corresponding I-V characteristics in comparison with Si-control JFET.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.154-155
• /
• 2012

The promise of nano-crystalites (nc) as a technological material, for applications including display backplane, and solar cells, may ultimately depend on tailoring their behavior through doping and crystallinity. Impurities can strongly modify electronic and optical properties of bulk and nc semiconductors. Highly doped dopant also effect structural properties (both grain size, crystal fraction) of nc-Si thin film. As discussed in several literatures, P atoms or radicals have the tendency to reside on the surface of nc. The P-radical segregation on the nano-grain surfaces that called self-purification may reduce the possibility of new nucleation because of the five-coordination of P. In addition, the P doping levels of ${\sim}2{\times}10^{21}\;at/cm^3$ is the solubility limitation of P in Si; the solubility of nc thin film should be smaller. Therefore, the non-activated P tends to segregate on the grain boundaries and the surface of nc. These mechanisms could prevent new nucleation on the existing grain surface. Therefore, most researches shown that highly doped nc-thin film by using conventional PECVD deposition system tended to have low crystallinity, where the formation energy of nucleation should be higher than the nc surface in the intrinsic materials. If the deposition technology that can make highly doped and simultaneously highly crystallized nc at low temperature, it can lead processes of next generation flexible devices. Recently, we are developing a novel CVD technology with a neutral particle beam (NPB) source, named as neutral beam assisted CVD (NBaCVD), which controls the energy of incident neutral particles in the range of 1~300eV in order to enhance the atomic activation and crystalline of thin films at low temperatures. During the formation of the nc-/pm-Si thin films by the NBaCVD with various process conditions, NPB energy directly controlled by the reflector bias and effectively increased crystal fraction (~80%) by uniformly distributed nc grains with 3~10 nm size. In the case of phosphorous doped Si thin films, the doping efficiency also increased as increasing the reflector bias (i.e. increasing NPB energy). At 330V of reflector bias, activation energy of the doped nc-Si thin film reduced as low as 0.001 eV. This means dopants are fully occupied as substitutional site, even though the Si thin film has nano-sized grain structure. And activated dopant concentration is recorded as high as up to 1020 #/$cm^3$ at very low process temperature (＜ $80^{\circ}C$) process without any post annealing. Theoretical solubility for the higher dopant concentration in Si thin film for order of 1020 #/$cm^3$ can be done only high temperature process or post annealing over $650^{\circ}C$. In general, as decreasing the grain size, the dopant binding energy increases as ratio of 1 of diameter of grain and the dopant hardly be activated. The highly doped nc-Si thin film by low-temperature NBaCVD process had smaller average grain size under 10 nm (measured by GIWAXS, GISAXS and TEM analysis), but achieved very higher activation of phosphorous dopant; NB energy sufficiently transports its energy to doping and crystallization even though without supplying additional thermal energy. TEM image shows that incubation layer does not formed between nc-Si film and SiO2 under later and highly crystallized nc-Si film is constructed with uniformly distributed nano-grains in polymorphous tissues. The nucleation should be start at the first layer on the SiO2 later, but it hardly growth to be cone-shaped micro-size grains. The nc-grain evenly embedded pm-Si thin film can be formatted by competition of the nucleation and the crystal growing, which depend on the NPB energies. In the evaluation of the light soaking degradation of photoconductivity, while conventional intrinsic and n-type doped a-Si thin films appeared typical degradation of photoconductivity, all of the nc-Si thin films processed by the NBaCVD show only a few % of degradation of it. From FTIR and RAMAN spectra, the energetic hydrogen NB atoms passivate nano-grain boundaries during the NBaCVD process because of the high diffusivity and chemical potential of hydrogen atoms.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.114-114
• /
• 2000

III-nitride 게 물질들은 blue와 UV 영역의 LED, LD와 같은 광소자뿐만 아니라 HBT, FET와 같은 전자소자로도 널리 응용되고 있다. 이와 같은 물질을 이용한 소자를 제작할 경우 낮은 저항의 ohmic contact은 필수적이다. p-GaN의 ohmic contact은 아직까지 많은 문제점을 내포하고 있다. 그 중의 하나는 높은 doping 농도(>1018cm-3)의 p-GaN 박막을 성장하기가 어렵다는 것이며, 또 하나는 낮은 접촉 비저항을 얻기 위해선 7.5eV 이상의 큰 재가 function을 지닌 금속을 선택해야 한다. 그러나 5.5eV 이상의 재가 function을 갖는 금속은 존재하지 않는다. 위와 같은 문제점들은 p-GaN의 접촉 비저항이 10-2$\Omega$cm2이상의 높은 값을 갖게 만들고 있으며 이에 대한 해결방안으로는 고온의 열처리를 통하여 p-GaN와 금속사이에서 화학적 반응을 일으킴으로써 표면근처에서 캐리어농도를 증가시키고, 캐리어 수송의 형태가 tunneling 형태로 일어날 수 있도록 하는 tunneling current mechaism을 이용하는 것이다. 이에 본 연구에서는 MOCVD로 성장된 p-GaN 박막을 Mg의 activation을 증가시키기 위해 N2 분위기에서 4분간 80$0^{\circ}C$에서 RTA로 annealing을 하였으며, ohmic 접촉을 위한 금속으로 높은 재가 function과 좋은 adhesion 그리고 낮은 자체저항을 가지고 있는 Ni/ZSi/Ni/Au를 ohmic metal로 하여 contact한 후에 $700^{\circ}C$에서 1분간 rapid thermal annealing (RTA) 처리를 했다. contact resistance를 계산하기 위해 circular-TLM method를 이용하여 I-V 특성을 조사하였고, interface interaction을 알아보기 위해 SEM과 EDX, 그리고 XRD로 분석하였다. 또한 추가적으로 Si 계열의 compound metal인 PdSi와 PtSi에 대한 I-V 특성도 조사하여 비교하여 보았다.