• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.4
• /
• pp.31-37
• /
• 2010

In this paper, highly efficient dual-band class-F power amplifiers(PAs) for cellular and WLAN bands are suggested and implemented. For the first step, single-band class-F amplifiers at 840MHz, 2.4GHz are designed using commercial E-pHEMT FETs. The performance of two single band PAs are as much as 81.2% of efficiency with the output power of 24.4dBm with 840MHz PA and 93.5% of efficiency with 22.4dBm from the 2.4GHz. For the dual-band class-F PA, the harmonic controlling circuit with ideal SPDT switch was suggested. The length of transmission line is variable by a SPDT switch. As a results, the operation in 840MHz showed the peak efficiency of 60.5% with 23.5dBm, while in 2.4GHz mode the efficiency was 50.9% with the output power of 19.62dBm. Besides, it is shown that the harmonic controller of class-F above 2Ghz could be implemented on the low cost FR-4 substrate.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.195-195
• /
• 2012

Recently, graphene based solution-gated field-effect transistors (SGFETs) have been received a great attention in biochemical sensing applications. Graphene and reduced graphene oxide (RGO) possess various advantages such as high sensitivity, low detection limit, label-free electrical detection, and ease of fabrication due to their 2D nature and large sensing area compared to 1D nanomaterials- based nanobiosensors. Therefore, graphene or RGO -based SGFET is a good potential candidate for sensitive detection of protons (H+ ions) which can be applied as the transducer in various enzymatic or cell-based biosensing applications. However, reports on detection of H+ ions using graphene or RGO based SGFETs have been still limited. According to recent reports, clean graphene grown by CVD or exfoliation is electrochemically insensitive to changes of H+ concentration in solution because its surface does not have terminal functional groups that can sense the chemical potential change induced by varying surface charges of H+ on CVD graphene surface. In this work, we used RGO -SGFETs having oxygen-containing functional groups such as hydroxyl (OH) groups that effectively interact with H+ ions for expectation of increasing pH sensitivity. Additionally, we also investigate RGO based SGFETs for bio-sensing applications. Hydroloytic enzymes were introduced for sensing of biomolecular interaction on the surface of RGO -SGFET in which enzyme and substrate are acetylcholinesterase (AchE) and acetylcholine (Ach), respectively. The increase in H+ generated through enzymatic reaction of hydrolysis of Ach by AchE immobilized on RGO channel in SGFET could be monitored by the change in the drain-source current (Ids).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.184-184
• /
• 2011

반도체 전자 소자의 초고집적회로(VLSI, Very Large Scale Integrated Circuit)가 수년간 지속됨에 따라 실리콘 기반으로 하는 MOSFET 성능의 한계에 도달하게 되었다. 재료 물성, 축소, 소자 공정 등에 대한 원인으로 이를 극복하고자 하는 재료와 성능향상에 관한 연구가 진행되고 있다. 이에 기존 시스템의 전자의 전하 정보만을 응용하는 것이 아니라 전자의 스핀 정보까지 고려하는 스핀트로닉스 연구분야가 주목을 받고 있다. Spin-FET는 스핀 주입, 스핀 조절, 스핀측정 등으로 나뉘어 연구되고 있으며 이 중 스핀 주입의 효율 향상이 우선시 해결되어야 한다. 일반적으로 스핀 주입 과정에서 소스가 되는 강자성체와 스핀 확산 거리가 긴 반도체 물질과의 Conductance mismatch가 문제되고 있다. 이에 자성 반도체는 근본적인 문제를 해결하고 반도체와 자성체의 특성을 동시에 나타내는 물질로써, Si과 Ge (4족) 등의 반도체뿐만 아니라, GaAs, InP (3-5족), ZnO, ZnTe (2-6족) 등의 반도체 또한 많은 연구가 이루어지고 있다. 자성 반도체에서 해결해야 할 가장 큰 문제는 물질이 자성을 잃는 Curie 온도를 상온 이상으로 높이는 것이다. 이에 본 연구는 전이금속이 도핑된 4족 Si 반도체 박막을 성장하고 후처리 공정을 통하여 나타나는 구조적, 자기적 특성을 연구하였다. 펄스 레이저 증착 방법을 통하여 p-type Si 기판위에 전이금속 Fe이 도핑된 박막을 500 nm 로 성장하였다. 성장 온도는 $250^{\circ}C$로 하였고, 성장 분압은 $3 {\times}10^{-3}$Torr 로 유지하며 $N_2$ 가스를 사용하였다. 구조적 결과를 보기 위해 X선 회절 분석과 원자력 현미경 결과를 확인하였고, 자기적 특성을 확인하기 위해 저온에서 초전도 양자 간섭계로 조사하였다. XRD를 통해 (002)면, (004)면의 Si 기판 결정을 보았으며, Fe 관련된 이차상이 형성됨을 예측해 보았다. ($Fe_3Si$, $Fe_2Si$ 등) 초전도 양자 간섭계에서 20 K에서 측정한 이력 현상을 관찰하고, 온도변화에 따른 전체 자기모멘트를 관찰하였으며 이는 상온에서도 강자성 특성이 나타남을 확인하였다.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.9
• /
• pp.1115-1124
• /
• 1988

A two-dimensional systolic array for fast Fourier transform, which has a regular and recursive VLSI architecture is presented. The array is constructed with identical processing elements (PE) in mesh type, and due to its modularity, it can be expanded to an arbitrary size. A processing element consists of two data routing units, a butterfly arithmetic unit and a simple control unit. The array computes FFT through three procedures` I/O pipelining, data shuffling and butterfly arithmetic. By utilizing parallelism, pipelining and local communication geometry during data movement, the two-dimensional systolic array eliminates global and irregular commutation problems, which have been a limiting factor in VLSI implementation of FFT processor. The systolic array executes a half butterfly arithmetic based on a distributed arithmetic that can carry out multiplication with only adders. Also, the systolic array provides 100% PE activity, i.e., none of the PEs are idle at any time. A chip for half butterfly arithmetic, which consists of two BLC adders and registers, has been fabricated using a 3-um single metal P-well CMOS technology. With the half butterfly arithmetic execution time of about 500 ns which has been obtained b critical path delay simulation, totla FFT execution time for 1024 points is estimated about 16.6 us at clock frequency of 20MHz. A one-PE chip expnsible to anly size of array is being fabricated using a 2-um, double metal, P-well CMOS process. The chip was layouted using standard cell library and macrocell of BLC adder with the aid of auto-routing software. It consists of around 6000 transistors and 68 I/O pads on 3.4x2.8mm\ulcornerarea. A built-i self-testing circuit, BILBO (Built-In Logic Block Observation), was employed at the expense of 3% hardware overhead.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.6
• /
• pp.584-597
• /
• 2011

In this paper, low-loss and high-power RF SP6T switch chips are designed, fabricated and measured for GSM/EGSM/DCS/PCS applications using WIN Semiconductors 0.5 ${\mu}m$ pHEMT process. We utilized a combined configuration of series and series-shunt structures for optimized switch performance, and a common transistor structure on a receiver path for reducing chip area. The gate width and the number of stacked transistors are determined using ON/OFF input power level of the transceiver system. To improve the switch performance, feed-forward capacitors, shunt capacitors and parasitic FET inductance elimination due to resonance are actively used. The fabricated chip size is $1.2{\times}1.5\;mm^2$. S-parameter measurement shows an insertion loss of 0.5~1.2 dB and isolation of 28~36 dB. The fabricated SP6T switch chips can handle 4 W input power and suppress second and third harmonics by more than 75 dBc.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.6 s.360
• /
• pp.60-68
• /
• 2007

A technique is presented to extract differential second harmonic output from common source nodes of a cross-coupled P-& N-FET oscillator. Provided the impedances at the common source nodes are optimized and the fundamental swing at the VCO core stays in a proper mode, it is found that the amplitude and phase errors can be kept within $0{\sim}1.6dB$ and $+2.2^{\circ}{\sim}-5.6^{\circ}$, respectively, over all process/temperature/voltage corners. Moreover, an impedance-tuning circuit is proposed to compensate any unexpectedly high errors on the differential signal output. A Prototype 5-GHz VCO with a 2.5-Hz LC resonator is implemented in $0.18-{\mu}m$ CMOS. The error signal between the differential outputs has been measured to be as low as -70 dBm with the aid of the tuning circuit. It implies the push-push outputs are satisfactorily differential with the amplitude and phase errors well less than 0.34 dB and $1^{\circ}$, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.6
• /
• pp.648-654
• /
• 2003

Diamond MIS(Metal-Insulator-Semiconductor) diodes and MISFETs(Metal-Insulator-Semiconductor Field Effect Transistors) were fabricated by employing various fluorides as gate insulator, and their electrical properties were closely investigated by means of C-V measurements. The A1/BaF$_2$/diamond MIS structure exhibited outstanding electrical properties. The MIS diode showed a very low surface state density of ∼10$\^$10//$\textrm{cm}^2$ eV near the valence band edge, and the observed effective mobility(${\mu}$$\_$eff/) of the MISFET was 400 $\textrm{cm}^2$/Vs, which is the highest value obtained until now in the diamond FET. From the chemiphysical point of view, the above result might be explained by the reduction of adsorbed-oxygen on the diamond surface via strong chemical reaction by the constituent Ba atom in the insulator during the film deposition(Oxygen-Gettering Effect).

• Journal of Yeungnam Medical Science
• /
• v.37 no.1
• /
• pp.47-53
• /
• 2020

Background: This study was conducted to analyze clinical factors that can affect pregnancy rates in normal responders undergoing the freeze-all policy in in vitro fertilization. Methods: We evaluated 153 embryo transfer cycles in 89 infertile women with normal response to controlled ovarian stimulation (COS). After COS, all embryos were cultured to the blastocyst stage, and good quality blastocysts were vitrified for elective frozen-thawed embryo transfer (FET). Clinical variables associated with COS and the results of COS and culture, including the number of retrieved oocytes, fertilized oocytes, and frozen blastocysts were compared between the pregnant group and the non-pregnant group. Results: After a single cycle of COS for each patient, 52 patients became pregnant while 37 did not. Significant differences were observed in the number of matured oocytes, fertilized oocytes, frozen blastocysts, and transferred embryos. The number of frozen blastocysts in the pregnant group was almost twice that in the non-pregnant group (5.6±3.1 vs. 2.8±1.9, p<0.001). The area under the receiver operating characteristic curve for the 4 frozen blastocysts was 0.801 in the pregnant group. Conclusion: In the freeze-all policy, the number of matured oocytes, number of fertilized oocytes, and number of frozen blastocysts might be predictive factors for pregnancy.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1998.02a
• /
• pp.110-110
• /
• 1998

GaN는 직접천이형 에너지 캡을 가지며 In과 화합물을 형성할 경우 1.geV-3.4eV까지 다양한 에너지 캡을 가지므로 청색 발광소자 고출력소자 고온 전자소자둥 웅용성이 많 은 물절로서 각광을 받고 있다. 그러나 G랴‘에 적합한 기판이 없다는 문제점으로 인하여 F FET, LD와 같은 다양한 구조의 웅용에 제 약이 따랐다. 이에 본 연구에서는 RF(radio frequency) Plasma-Assisted MBE( molecular beam e epitaxy )를 이용하여 InxGaj xN/G암J 양자우물 구조를 성장하였다. 이렇게 성장된 I InxGaj xN 박막과 InxGaj xN/GaN 양자우물구조의 특성의 분석은 광학적 특성올 PL( p photoluminescence ) , 결 정 성 의 분석 은 XRD ( x-ray diffraction ), 표면 과 단변 의 계 변 특성은 SEM(scanning electron microscopy)을 이용하여 분석하였다. 저온 PL의 측정결 과 기판온도를 680$^{\circ}$C로 고정한 후 In cell의 온도를 650$^{\circ}$C에서 775$^{\circ}$C까지 증가함에 따라 I InxGaj xN에 관계된 피크위치가 약3이neV정도 red shift 함을 관찰할 수 있었다. 한편 I InxGaj xN/GaN 양자우물구조의 경우 PL피크가 3.2없eV로써 InxGaj- xN의 PL 피크에 비 해 에서 약 25me V 고에너지 이동이 관측되었으며 이것은 우불 내에서 에너지레벨의 c confinement효과에 의해 에너지의 변화에 의한 것엄올 확인하였으며, 양자우물 구조에서 우물의 두께를 줄임에 따라 변화 폭은 1이neV정도 고에너지 이동을 관찰할 수 있었다. X XRD 측정의 결과 In의 mole fraction에 따라 격자상수의 변화를 관찰하였으며, 결정 성의 변화를 피크의 세기로 관찰하였다 .. XRD로 판단한 In의 mole fraction은 0.2임을 알 았다 .. SEM 측정은 표변과 단면의 측정으로서 표연특성과 단면의 특성을 InxGaj xN, I InxGaj xN/GaN 양자우물 구조 모두 알아보았다. 측정 결과 InxGaj-xN의 성 장조건으로 기판온도가 낮아지면서 표면의 거칠기 정도가 증가하였으며,680$^{\circ}$C의 기판온도에서 성장 한 양자우물 구조에 있어서 매끄라운 표면올 얻올 수 있었다.

• Journal of Sensor Science and Technology
• /
• v.7 no.4
• /
• pp.271-278
• /
• 1998

A ISFET-based glucose sensor has inherent problems such as low sensitivity, drift effect and long response time. For that reason, a amperometric actuation technique was introduce to make a highly sensitivity of the ISFET glucose sensor with a Pt actuator, which electrolyzes $H_2O_2$, one of the by a by-products of the oxidation reaction of glucose. Moreover, a potential-step measurement method detecting response by only the electrolysis of $H_2O_2$ was developed for eliminating a drift problem. The operation characteristics of ISFET-based glucose sensor was improved by using the amperometric actuation and a measurement techniques. The fabricated ISFET glucose sensor is shown good operation such as characteristics(30mM PBS, about 26mV/decade) and linearity. A portable glucose meter with a highly resolution by using the fabricated ISFET-based glucose sensor with Pt actuation was developed and its characteristics investigated.