• Korean Journal of Materials Research
• /
• v.23 no.11
• /
• pp.661-665
• /
• 2013

We investigated the characteristics of electroless plated Cu films on screen printed Ag/Anodized Al substrate. Cu plating was attempted using neutral electroless plating processes to minimize damage of the anodized Al substrate; this method used sodium hypophosphite instead of formaldehyde as a reducing agent. The basic electroless solution consisted of $CuSO_4{\cdot}5H_2O$ as the main metal source, $NaH_2PO_2{\cdot}H_2O$ as the reducing agent, $C_6H_5Na_3O_7{\cdot}2H_2O$ and $NH_4Cl$ as the complex agents, and $NiSO_4{\cdot}6H_2O$ as the catalyser for the oxidation of the reducing agent, dissolved in deionized water. The pH of the Cu plating solutions was adjusted using $NH_4OH$. According to the variation of pH in the range of 6.5~8, the electroless plated Cu films were coated on screen printed Ag pattern/anodized Al/Al at $70^{\circ}C$. We investigated the surface morphology change of the Cu films using FE-SEM (Field Emission Scanning Electron Microscopy). The chemical composition of the Cu film was determined using XPS (X-ray Photoelectron Spectroscopy). The crystal structures of the Cu films were investigated using XRD (X-ray Diffraction). Using electroless plating at pH 7, the structures of the plated Cu-rich films were typical fcc-Cu; however, a slight Ni component was co-deposited. Finally, we found that the formation of Cu film plated selectively on PCB without any lithography is possible using a neutral electroless plating process.

• Bulletin of the Korean Chemical Society
• /
• v.10 no.1
• /
• pp.5-8
• /
• 1989

Conventional ceramic method has been used to prepare the green phase, $Y_2BaCuO_5$, commonly observed in 90-K superconductor $YBa_2Cu_3O_P{7-{\delta}}$as an impurity phase. The powder X-ray diffraction analysis indicates that $Y_2BaCuO_5$ has an orthorhombic symmetry with lattice parameter of a = 12.2 $\AA$, b = 5.61 $\AA$, and c = 7.14 $\AA.$ The average g-value 2.13 observed in ESR spectrum is attributable to Cu2+ stabilized in $C_{4v}$ field. From the magnetic susceptibility ($\mu$eff = 2.29 BM) and the ESR measurements, it is confirmed that Cu(II) $3d^9$ electrons in $Y_2BaCuO_5$ are localized and can be characterized by Curie-Weiss behavior. Optical reflectance spectrum shows a broad absorption peak around 680 nm due to dxy ${\rightarrow}$ $dx^2-y^2$ eletronic transition.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.378-378
• /
• 2011

본 연구에서는 ZnO 나노선 기판을 제작하여 그 위에 밴드갭이 낮은 물질인 CdS, CdSe를 증착시킨 후 p-type 반도체 물질인 CuSCN을 증착시켜 안정성이 향상된 양자점 감응형 태양전지를 제작하였다. ZnO 나노선 기판은 투명한 FTO 기판 위에 ZnO를 진공증착시켜 seed layer를 제작하고 그 위에 $10{\mu}m$정도의 길이의 나노와이어를 성장시킨 후, 밴드갭이 낮은 CdS, CdSe 물질과의 다중접합을 이용하여 제작하고, 이러한 나노선 구조위에 chemical solution deposition을 이용하여 ${\beta}$-CuSCN을 형성시켰다. 양자점 감응형 태양전지는 ZnO 나노선을 photoanode로 이용하고 ZnO 나노선은 암모니아수와 아연염을 이용한, 비교적 저온의 수열합성법을 통해 합성하였고, sensitizer로 쓰인 CdS, CdSe 물질은 CBD방식을 통하여 합성된 나노선 위에 in-situ로 접합시켰다. 또한, 기존의 액체전해질을 이용한 양자점 감응형 태양전지의 안정성을 향상시키기 위해 p-type의 반도체 물질인 CuSCN물질을 propyl sulfide를 이용, ${\sim}80^{\circ}C$의 열을 가하여 in-situ 방식으로 다공성 구조에 효율적으로 접합이 가능하도록 deposition하였다. 일반적으로, CuSCN film은 홀 전도체로서의 장점을 지닌 반면, 전도성이 낮은 단점이 있기 때문에 이를 향상시키기 위해서 첨가제를 이용, 농도에 따라서 전도도가 향상되고 셀의 성능이 향상되는 것을 확인하였다. 이와 같이 합성된 구조는 주사전자현미경(SEM), X-선 회절(XRD), 솔라시뮬레이터 등의 분석장비를 이용하여 태양전지로서의 특성을 분석하였다. 또한 안정성 평가를 위하여 시간에 따른 셀의 특성변화도 비교하였다.

• Applied Chemistry for Engineering
• /
• v.9 no.2
• /
• pp.165-171
• /
• 1998

The $Y_1Ba_2Cu_3O_{7-x}$(123) superconductor powders were prepared by pyrophoric synthesis method(PSM) using $Y_2O_3$(99.9%), $BaCO_3$(99.9%), and CuO(99.9%) powders. The phase formation and reaction kinetics of 123 superconductor manufactured with powders prepared in various pHs of pyrophoric synthetic solution have been studied through the experiments at various heat treatment temperatures and times. Inductively coupled plasma(ICP) spectroscopy and scanning electron microscopy(SEM) measurements were performed to examine the composition and morphology of the sample. X-ray diffraction(XRD) analysis was done to determine phase formation and conversion ratio of Y-Ba-Cu-O systems. The 123 powder prepared at pH 7(${\pm}0.3$) yields the best result in terms of purity, homogeneity, and reactivity. The activation energies(${\Delta}E_a$) of 123 phase formation were found to be 191 kJ/mol and 230kJ/mol in solid state reaction method and pyrophoric synthesis method, respectively.

• Environmental Engineering Research
• /
• v.13 no.3
• /
• pp.131-135
• /
• 2008

In this study, Fe(VI) was employed as a multi-functional agent to treat the simulated industrial wastewater contaminated with Cu(II)-EDTA through oxidation of EDTA, decomplexation of Cu(II)-EDTA and subsequent removal of free copper through precipitation. The decomplexation of $10^{-4}\;M$ Cu(II)-EDTA species was performed as a function of pH at excess concentration of Fe(VI). It was noted that the acidic conditions favor the decomplexation of Cu(II)-EDTA as the decomplxation was almost 100% up to pH 6.5, while it was only 35% at pH 9.9. The enhanced degradation of Cu(II)-EDTA with decreasing the pH could be explained by the different speciation of Fe(VI). $HFeO_4^-$ and $H_2FeO_4$, which are relatively more reactive than the unprotonated species $FeO_4^{2-}$, are predominant species below neutral pH. It was noted that the decomplexation reaction is extremely fast and within 5 to10 min of contact, 100% of Cu(II)-EDTA was decomplexed at pH 4.0. However, at higher pH (i.e., pH 10.0) the decomplexation process was relatively slow and it was observed that even after 180 min of contact, maximum ca 37% of Cu(II)-EDTA was decomplexed. In order to discuss the kinetics of the decomplexation of Cu(II)-EDTA, the data was slightly fitted better for the second order rate reaction than the first order rate reaction in the excess of Fe(VI) concentration. On the other hand, the removal efficiency of free Cu(II) ions was also obtained at pH 4.0 and 10.0. It was probably removed through adsorption/coagulation with the reduced iron i.e., Fe(III). The removal of total Cu(II) was rapid at pH 4.0 whereas, it was slow at pH 10.0. Although the decomplexation was 100% at lower pH, the removal of free Cu(II) was relatively slow. This result may be explicable due to the reason that at lower pH values the adsorption/coagulation capacity of Fe(III) is greatly retarded. On the other hand, at higher pH values the decomplexation of Cu(II)-EDTA was partial, hence, slower Cu(II) removal was occurred.

• Journal of Sensor Science and Technology
• /
• v.32 no.4
• /
• pp.238-245
• /
• 2023

0.75(Bi_1/2Na_1/2)TiO₃-0.25SrTiO₃ (BNT-25ST) ceramics with high densities were successfully prepared at a sintering temperature of 1,000℃ by adding a mixture of 1 mol% CuO and 0.5 mol% Na₂CO₃ or 0.5 mol% CuO and 0.25 mol% Na₂CO₃. Double polarization-electric field (P-E) hysteresis curves and sprout-shaped bipolar strain-electric field (S-E) hysteresis curves with small negative strains were observed in the pristine and CuO-added BNT-25ST ceramics whereas the Na₂CO₃-added sample showed similar P-E and S-E curves to a typical ferroelectric. The pristine BNT-25ST ceramics showed an extremely large strain and a large-signal piezoelectric strain constant (d₃₃^*): 0.287 % at 80 kV/cm and 850 pm/V at 20 kV/cm. Similar values, 0.248 % at 80 kV/cm and 655 pm/V at 20 kV/cm, were obtained in the CuO-added sample. However, the pristine and CuO-added samples showed large hysteresis in unipolar S-E curves at an electric field of less than 20 kV/cm. The Na₂CO₃-added sample showed smaller values of the strain and d₃₃^* but displayed a linear change and small hysteresis in the unipolar S-E curve. The co-added sample with CuO and Na₂CO₃ displayed intermediate P-E and S-E hysteresis curves.

• Journal of Sensor Science and Technology
• /
• v.16 no.1
• /
• pp.11-16
• /
• 2007

CuO is an important transition metal oxide with many practical applications such as catalysts, p-type semiconductor, solar cells, magnetic storage media and cathode materials. In this contribution, nanocrystalline CuO powders were prepared by solution reduction method using copper chloride ($CuCl_{2}{\cdot}2H_{2}O$), hydrazine ($N_{2}H_{4}$) and NaOH and subsequent heat treatment. The gas sensor using nanocrystalline CuO powders showed high sensitivities to acetone and ethanol.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.9
• /
• pp.527-531
• /
• 2016

In this study, p-type thin film transistors consisting of CuO channels were fabricated by sol-gel process, with copper (II) acetate monohydrate precursors. At $500^{\circ}C$, the deposited films were fully converted into monoclinic phase CuO. The fabricated CuO thin film transistors deliver field effect mobility in saturation regime of $0.015cm^2/Vs$, and $I_{on}/I_{off}$ of ${\sim}10^3$. The degradation of the performance of the fabricated CuO thin film transistor caused by the exposure to air has been studied.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.3
• /
• pp.494-503
• /
• 1997

We investigated the initial stages of formation of the Cu/polyimide interface using another two methods by X-ray photoelectron spectroscopy. : One, in-situ measurement with increasing of Cu deposition thickness onto polyimide(PI), the other, measurement with decreasing of Cu thickness of Cu/pI film by $Ar^+$ ion etching. From these results, we find that the chemical reactions exist in Cu/PI interface. However, the measured chemical reactions were different according to experimental method.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2011.05a
• /
• pp.137-138
• /
• 2011

구리 이온은 -0.40V (vs. SCE)에서 전기화학적 환원이 일어나는 반면, 니켈 이온은 -1.19V (vs. SCE)에서 전착이 발생한다. 따라서, 단일 도금욕조 내에서 Ni-Cu 합금도금층을 제조하기 위해서는 두 금속 이온종 간의 전위차를 줄여주어야 하는데, 이를 위해 본 연구에서는 $Na_3C_6H_5O_7{\cdot}2H_2O$를 착화제로 사용하였다. 다양한 Ni-Cu 합금 도금층의 조성을 얻기 위하여 기본 도금욕 내 황산니켈과 황산구리의 비율을 10:1로 설정하였다. 도금 공정 조건에 따른 합금 도금층 조성 변화를 관찰하기 위하여 도금액 pH와 교반 속도에 따른 도금층 조성 변화를 분석하였으며, 도금액의 UV-VIS과 도금층의 XRD 와 SEM 측정을 통하여 도금욕과 도금층 간의 상관 관계를 유추하였다. 본 도금액에 사용된 $Na_3C_6H_5O_7{\cdot}2H_2O$ 착화제의 효과는 pH3에서 가장 현저하였으며, pH 변화 및 교반 속도 변화를 이용하여 다양한 합금 조성을 얻을 수 있었다.