• Journal of the Korean Society of Combustion
• /
• v.8 no.2
• /
• pp.1-6
• /
• 2003

Numerical simulations are conducted at atmospheric pressure in order to understand the effect of the oxygen enrichment level on structure of $CH_4/O_2/N_2$ premixed flames. Under several equivalence ratios the flame speeds are calculated and compared with those obtained from the experiments, the results of which are in good agreement. The effects of the oxygen enrichment are investigated on flames under fuel-rich conditions. As the oxygen enrichment level is increased from 0.21 to 1, the flame speed and the temperature are increased. The emission index of $CO_2$ is decreased in cases of flames for fuel rich mixtures, so the efficiency of combustion may be decreased. The maximum emission index of NO is obtained for 0.6 of the oxygen enrichment level.

• Journal of Mechanical Science and Technology
• /
• v.16 no.9
• /
• pp.1156-1165
• /
• 2002

The characteristics of combustion and radiation heat transfer of an oxygen-enhanced diffusion flame was experimentally analyzed. An infrared radiation heat flux gauge was used to measure the thermal radiation of various types of flames with fuel, air and pure oxygen. And the Laser Induced Incandescence (LII) technique was applied to characterize the soot concentrations which mainly contribute to the continuum radiation from flame. The results show that an oxygen-enhanced inverse diffusion flame is very effective in increasing the thermal radiation compared to normal oxygen diffusion flame. This seems to be caused by overlapped heat release rate of double flame sheets formed in inverse flame and generation of higher intermediate soot in fuel rich zone of oxygen-fuel interface, which is desirable to increase continuum radiation. And the oxygen/methane reaction at slight fuel rich condition (ø=2) in oxygen-enhanced inverse flame was found to be more effective to generate the soot with moderate oxygen availability.

• Journal of the Korean Society of Combustion
• /
• v.11 no.1
• /
• pp.19-26
• /
• 2006

Structure of edge flame established in a mixing layer, formed between two uniformly flowing pure $CH_4$ and pure $O_2$ streams, is numerically investigated by employing a detailed methane-oxidation mechanism. The numerical results exhibited the most outstanding distinction of using pure oxygen in the fuel-rich premixed-flame front, through which the carbon-containing compound is found to leak mainly in the form of CO instead of HC compounds, contrary to the rich $CH_4-air$ premixed flames in which $CH_4$ as well as $C_2H_m$ leakage can occur. Moreover, while passing through the rich premixed flame, a major route for CO production, in addition to the direct $CH_4$ decomposition, is found to be $C_2H_m$ compound formation followed by their decomposition into CO. Beyond the rich premixed flame front, CO is further oxidized into $CO_2$ in a broad diffusion-flame-like reaction zone located around moderately fuel-rich side of the stoichiometric mixture by the OH radical from the fuel-lean premixed-flame front. Since the secondary CO production through $C_2H_m$ decomposition has a relatively strong reaction intensity, an additional heat-release branch appears and the resulting heat-release profile can no longer be seen as a tribrachial structure.

• Journal of ILASS-Korea
• /
• v.18 no.1
• /
• pp.27-34
• /
• 2013

A preburner is one of the key components for a staged combustion cycle engine fueled by kerosene and Lox. Since it has oxygen rich combustion inside, temperature control is very crucial. The temperature of the exhaust gas should be low enough not to burn turbine blade and yet high to keep the efficiency high. In addition temporal and spatial deviations also managed strictly. Conventionally, the required average and maximum temperature are determined by engine system and the preburner should be developed to meet the criteria. Currently being developed preburner has 50K spatial temperature deviation requirement. It was estimated by numerical simulations and proven by tests. The numerical analysis were done with both supercritical condition and normal conditions. The tests results showed that the temperature deviations were less than expected, and the results from the test and simulations were well agreed when the supercritical conditions were considered. Above all, since the gas temperature created by the preburner is very stable with minimum deviation, the preburner developed can be used to drive a turbine and for gas-liquid combustion chambers.

• Journal of the Korean Society of Combustion
• /
• v.15 no.4
• /
• pp.9-14
• /
• 2010

Numerical simulations of freely propagating fuel-rich $CH_4/CH_3Cl$ premixed flames were performed at atmospheric pressure in order to understand the effect of the oxygen enrichment on the production of PAH. A chemical kinetic mechanism was used, which involved 157 gas-phase species and 1693 forward reactions. The calculated flame speeds were compared with the experiments for the flames established on the equivalence ratios of 1~1.6, the results of which were in good agreement. As the level of oxygen enrichment was increased, the concentrations of one or four ring aromatic hydrocarbons were decreased. This might cause the fact that the contribution of PAH species to soot was weakened.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.1
• /
• pp.89-96
• /
• 2013

Combustion pressures were measured to study combustion stability for an oxygen rich preburner by both of static and dynamic pressure sensors. The resolutions of each static and dynamic pressure sensor are the 1,000 Hz and 25,600 Hz, respectively. The nominal combustion pressure of the preburner was 200 bar but 80 bar was used at the several initial tests for the safety reason. Two stage ignition was applied to reduce the ignition impact for every tests including the tests with 200 bar combustion pressure. The tests lasted for 10 sec. max. and a little fluctuations of pressure was observed during the main mode. The measured pressures were studied by FFT analysis and no noticeable frequency coupling was found. Thus the preburner can be regarded as stable and it can be utilized for further study on staged combustion cycle liquid rocket engine.

• Journal of Astronomy and Space Sciences
• /
• v.28 no.3
• /
• pp.233-239
• /
• 2011

A series of computational analyses was performed to predict the cooling process by the cooling channel of preburners used for kerosene-liquid oxygen staged combustion cycle rocket engines. As an oxygen-rich combustion occurs in the kerosene fueled preburner, it is of great importance to control the wall temperature so that it does not exceed the critical temperature. However, since the heat transfer is proportional to the speed of fluid running inside the channel, the high heat transfer leads to a trade-off of pressure loss. For this reason, it is necessary to establish a certain criteria between the pressure loss and the heat transfer or the wall surface temperature. The design factors of the cooling channel were determined by the computational research, and a test model was manufactured. The test model was used for the hot fire tests to prove the function of the cooling mechanism, among other purposes.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.65-69
• /
• 2012

An oxygen rich preburner was tested and the responses from the pressure sensors were studied with FFT analysis. Since the limited capability of the static sensor, less than 250 Hz frequency domain was investigated and compared to the results of the dynamic sensors. As a result, 60 Hz harmonics were presented dominant in the combustion pressure and oxygen inlet pressure. While similar harmonics were shown with the dynamic sensor, it indicated that harmonics less than 60 Hz were very minor and the high frequency is more important.

• Journal of the Korean Society of Combustion
• /
• v.22 no.4
• /
• pp.51-56
• /
• 2017

The decomposition of tetrafluoromethane has been investigated with the reaction mechanism proposed for freely propagating $CH_4/CF_4/O_2/N_2$ premixed flames on the oxygen enrichment. The factors affecting on the removal efficiency of tetrafluoromethane were analyzed. The increase in flame temperature due to oxygen enrichment has a great influence on the removal efficiency of tetrafluoromethane. At the same oxygen enrichment condition, the removal efficiency in the rich flame is higher than one in the lean flame. The increase of the F/H ratio leads to decrease the flame temperature and the removal efficiency of tetrafluoromethan is decreased at the flame temperature of 2600 K or lower, The elementary reactions that dominate the consumption of tetrafluoromethane are (R1) $CF_4+M=CF_3+F+M$ and (R2) $CF_4+H=CF_3+HF$. (R1) has the greatest effect on the consumption of tetrafluoromethane under the oxygen enhanced flames.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.6
• /
• pp.45-52
• /
• 2021

A hot-firing test was conducted using gaseous-methane and gaseous-oxygen under highly fuel-rich condition as a prior study for the development of a liquid propellant small rocket engine. To compare combustion characteristics for various equivalence ratios, the oxygen flow rate was set to 12 g/s and the methane flow rate was changed according to the equivalence ratio. As a result, it was observed that the steady-state characteristic velocity obtained during the hot-firing test steeply rose in the latter part of each test: the difference between the former and the latter steady value was enhanced overall in proportion to the equivalence ratio. Based on this, the equivalence ratio range depending on the variational characteristics of the characteristic velocity could be divided into three combustion regimes.