• Knowledge Management Research
• /
• v.18 no.4
• /
• pp.137-157
• /
• 2017

With the rapid growth of the internet, Social Network Services (SNSs) have played an important role. As the use of SNSs increases, users experience a sense of responsibility to respond to other people's messages or requests, and consequently experience an social overload, feeling too much social support for other users. In this study, we examined the effects of social overload on loneliness and SNS discontinuous usage intention. To verify the research model, data were collected from 83 SNS users and analyzed using SmartPLS, a structural equation modeling tool. The results of this study showed that the communal orientation and the degree of use of SNS influenced the social overload, and the social overload had a significant effect on loneliness and SNS discontinuous usage intention. The findings of this study are expected to help understand the social overload and loneliness in the use of SNS, and may also provide a strategic direction for SNS service providers.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.119-124
• /
• 2003

In this study, retardation behavior of fatigue crack under single overloading of the mixed mode I+II state was experimentally investigated. To produce single overload in the mixed mode I+II state, the compact tension shear (CTS) specimen and loading device were used. The propagation tests for fatigue crack were performed under mode I loading overloading afterwards. We examined the observed deformation aspects, variation of fatigue life and crack propagation rate, and the aspects of retardation behavior from tests. The retardation effect of mixed-mode single overload on fatigue crack propagation behavior was smaller than that of mode I single overload. It has been confirmed that the retardation behavior did not immediately appear and the retardation length was short when the component of mixed-mode overload was changed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.04b
• /
• pp.328-332
• /
• 1993

Single overload tests are carried out for SS41. Specimens are used hollow type and solid type that stress condition prevail plane stress and plane strain at surface crack. According to the crack initiation and propagation period, single overload applies to three regime and overload ratios change into 1.5, 2.0. Crack retardation zones at initation range aren't different in both specimens respectively, however at propagation range come into large scale in hollow specimen. Delayed load cycles come into large scale in solid type. And the more the overload ratio increase, the larger the retardation zone increase but the magnitude doesn't exactly equal to the expected from the overload ratio.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.695-701
• /
• 2009

Side Buffer with Anti-Climber is absorber and anti climber during impact. The Overload Protection Device protects the car underframe from being damaged in case of release of the overload protection. In case of heavy impacts(60 ton), the load is converted into deformation energy by plastic deformation of the tear-off bolts This paper describes a study on this function applied for Side Buffer and Overload Protection Device.

• Aerospace Engineering and Technology
• /
• v.3 no.2
• /
• pp.208-216
• /
• 2004

Advanced overload protection module for full scale airframe structural test was developed by improving the existing overload protection module. When performing the full scale airframe structural test, overload can be applied to the test article due to unexpected situations such as system shutdown, test article failure, and deficiency of design strength. Therefore, the overload protection module is needed for protecting the test article in unexpected overload situations. In this paper, the function of the existing overload protection module was summarized for each component and the problems encountered when using it in structural test were analyzed in addition, the development of advanced overload protection module was described.

• Journal of Ocean Engineering and Technology
• /
• v.2 no.2
• /
• pp.122-129
• /
• 1988

Recently with the rapid development in marine and shipbuliding industries such as marine structures, ship and chemical plants, there occurs much interest in the study of corrosion fatigue characteristics which was closed up an important role in mechanical design. In this study, the 5086 Al-alloy was tested by use of rotary bending fatigue tester. The retardation effect of overload on the corrosion fatigue crack propagation in sea environment was quantitatively studied. 1) Retardation effect of corrosion fatigue crack propagation is most eminent when overload ratio is 1.52, overload magnitude corresponds to about 77% and 55% of yield strength and tensile strength respectively. 2) After overload ratio 1.52 was used, retardation of corrosion fatigue crack growth rate is largely retarded and quasi-threshold stress intensity factor range($\Delta\textrm{K}_{th}$) appears. 3) According to m of experimental constant, retardation effect of corrosion fatigue crack propagation corresponds to about 25% of constant stress amplitude when overload ratio is 1.52. 4) When overload ratio 1.52 was used, retardation parameter (RP) decreases to about 0.43 and corrosion sensitivity (S)decreses to about 2.1.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.2
• /
• pp.419-424
• /
• 2011

The system-on-board detectable and controllable the electrical fires due to ground fault(GF), arc fault and overload is implemented. The system IC for controlling and preventing the electrical fires is available to this system. The GF detection circuit for detecting the electrical leakage current, the arc fault detection circuit and the overload detection circuit controllable the input voltage for flowing the overload current are designed. The GF detection circuit and the arc fault detection circuit are good operated to the electrical leakage current and the arc signal, respectively. It is confirmed that the overload detection circuit has shown no erratic operation with the noise or the load variation and is only operated at the overload condition.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.53 no.9
• /
• pp.513-520
• /
• 2004

In the paper, we summarize the result of the experimental research for the overload criteria of domestic distribution transformers considering the electric consumption patterns of customers. For the basic characteristic data of distribution transformer overload, the actual experiments are accomplished. The field data of loads are surveyed from sample transformers for analyzing the consumption pattern of customer load. The load data acquisition devices are equipped, and the algorithm of load pattern classification is applied. In addition to this efforts, various load pattern data. in past are gathered. Then the representative load pattern of each customer type in domestic is extracted. The final results of overload criterions are presented as tabular form through the results of experiments and survey are combined. The field test of the experiment results is peformed using the special manufactured transformers, which can measure both the load and top-oil temperature of transformer. Through this, we verify that the results of field test are similar to the laboratory one and the Proposed overload criteria can be effectively applied to the real system.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.909-914
• /
• 2007

In this paper, an overload detecting algorithm for an excavator is presented. The proposed overload detecting algorithm is based on the time series analysis especially moving window. The main purpose of this paper is to prevent a damage or crack from the fatigue in advance. 16 channel sensors data are considered and maximum stress is computed by a sensor fusion method every moving window. After the maximum stress every window is compared with a given threshold, this overload detecting algorithm decides overload or not.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.4
• /
• pp.952-960
• /
• 1996

In this paper, a new overload control scheme is proposed for a control system in ATM switching system. The proposed control scheme includes a counter that conunts the number of accepted calls and is decreased at cach D time interval. In overload condition of call processor, the control scheme detects over load condition when the counter value reaches a certain threshold value. Under overload condition, processor utilization is measured and the value of the D is updataed according to the difference between measured processor utilization and target utilization. A new call is accepted accepted only if the value of the counter is less than the threshold value. In overflow condition of cell traffic, accept probability of new call is reduced exponetially according to the elapsed time. The results of simulation show that the proposed overload contorl scheme maintains the target utilization very well under the various processor overload conditions and reduces the cell loss probability under the cell overflow conditions.