• Journal of The Korean Society of Grassland and Forage Science
• /
• v.10 no.1
• /
• pp.10-14
• /
• 1990

The effects of coating materials on germination, establishment and herbage production were investigated in a laboratory and field over 1988-1989. For this purpose, four treatments of lime 50 % + briquet ash 50 %, briquet ash, dairy excreta and fowldung as coating material were applied to orchardgrass and red clover with meth ylcellulose. The germination rate of lime 50 % + briquet ash 50 % (70.6 %), briquet ash (84.0 %), dairy excreta (66.0 %) and fowldung (61.3 %) in orchardgrass were, showing lower than that of the control (86.6 %), respectively and the rate of red clover ranged from 59.0 to 18.6 %. Establishment in orchardgrass were from 2.0 to 0.9 %, showing lower than the control, whole a little higher except dairy excreta and fowldung treatments in red clover than the control. The DM yield of lime 50 % + briquet ash 50 % treatment was almost same to the control and other treatment showed lower yield compared with the yield of the control. The benefical effect of seed coating on field performance was minimal especially in terms of establishment and yield increase.

• Food Science and Preservation
• /
• v.8 no.2
• /
• pp.181-186
• /
• 2001

The objective of this study is to determine the effect of soy protein isolate (SPI) film coating on the color, firmness, viscosity and weight loss of Rice Cake stored at 15, 20 and $25^{\circ}C$ (RH 50%) for 30 days. Raw materials mixed with SPI and cocoa powder (10:0, 7:3, 5:5, 3:7, w/w) were prepared. After adding sugar and shortening to raw materials, the mixture were refined to 25 micron of particle size. Coating of Rice Cake were carried out at $65^{\circ}C$. SPI coated Rice Cake had higher internal and external firmness comparing to the control at $25^{\circ}C$. SPI coated Rice Cake showed smooth surface morphology and had 0.71-1.01 mm of thickness. SPI coated Rice Cake showed less weight loss for 30 days compared to controls. SPI coating solution was successfully coated on Rice Cake and extended shelf-life over 15 days at room temperature.

• Journal of Powder Materials
• /
• v.7 no.2
• /
• pp.63-70
• /
• 2000

Thermal spray coating process has proven to be effective at producing hard, dense, wear resistance coatings on the relatively mild substrates. Among several spraying techniques, HVOF (High Velocity Oxygen Fuel) and plasma coating processes, which are preferentially used for the wear resistance application such as capstans, have been applied in this study. The effects of pre-treatment, it-process and post-treatment parameters on the wear and mechanical properties of WC+12%Co, Cr3C2 and Al2O3 powder coatings have been investigated and correlated with the microstructures. The results indicated that the carbide coating was more preferable to the oxide coatings and the post-treatments consisting of vacuum annealing and sealing on carbide coatings led to significant improvements in wear resistance, adhesive strength and coating phase stabilization over the other processing techniques in this application.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.20 no.1
• /
• pp.61-66
• /
• 2000

An experiment was conducted to evaluate the effects of seed coating on germination and early growth of tall fescue (Festuca arundinacea Schr.), orchardgrass (Dactylis glomerata L.), and alfalfa (Medicago sativa L.) over sown on unploughed hilly and forested areas. Establishment and early growth of coated tall fescue and orchardgrass on unploughed hilly area were not significantly influenced by seed coating. Establishment and early growth of coated alfalfa on unploughed hilly area were higher than non-coated and showed 4.7% and 4.0 g/m2, respectively. Establishment of coated tall fescue (11.8%) on forested area were higher than noncoated (0.3%), but ealy growth of tall fescue was not significantly influences by seed coating. Establishment of over sown orchardgrass on forested area was not significantly affected by seed coating, but early growth of coated seed (18.7%) was better than that of non-coated (0.3%). Establishment of coated alfalfa on forested area were higher than those of non-coated. Results of this study indicate that the establishment and early growth of over sown tall fescue, orchardgrass, and alfalfa could be improved by seed coating.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.416-416
• /
• 2016

Organic-inorganic metal halide perovskite solar cells have received attention because it has a number of advantages with excellent light harvesting, high carrier mobility, and facile solution processability and also recorded recently power conversion efficiency (PCEs) of over 20%. The major issue on perovskite solar cells have been reached the limit of small area laboratory scale devices produced using fabrication techniques such as spin coating and physical vapor deposition which are incompatible with low-cost and large area fabrication of perovskite solar cells using printing and coating techniques. To solution these problems, we have investigated the feasibility of achieving fully printable perovskite solar cells by the blade-coating technique. The blade-coating fabrication has been widely used to fabricate organic solar cells (OSCs) and is proven to be a simple, environment-friendly, and low-cost method for the solution-processed photovoltaic. Moreover, the film morphology control in the blade-coating method is much easier than the spray coating and roll-to-roll printing; high-quality photoactive layers with controllable thickness can be performed by using a precisely polished blade with low surface roughness and coating gap control between blade and coating substrate[1]. In order to fabricate perovskite devices with good efficiency, one of the main factors in printed electronic processing is the fabrication of thin films with controlled morphology, high surface coverage and minimum pinholes for high performance, printed thin film perovskite solar cells. Charge dissociation efficiency, charge transport and diffusion length of charge species are dependent on the crystallinity of the film [2]. We fabricated the printed perovskite solar cells with large area and flexible by the bar-coating. The morphology of printed film could be closely related with the condition of the bar-coating technique such as coating speed, concentration and amount of solution, drying condition, and suitable film thickness was also studied by using the optical analysis with SEM. Electrical performance of printed devices is gives hysteresis and efficiency distribution.

• Journal of Animal Reproduction and Biotechnology
• /
• v.38 no.3
• /
• pp.121-130
• /
• 2023

Background: Coating a culture plate with molecules that aid in cell adhesion is a technique widely used to produce animal cell cultures. Extracellular matrix (ECM) is known for its efficiency in promoting adhesion, survival, and proliferation of adherent cells. Gelatin, a cost-effective type of ECM, is widely used in animal cell cultures including feeder-free embryonic stem (ES) cells. However, the optimal concentration of gelatin is a point of debate among researchers, with no studies having established the optimal gelatin concentration. Methods: In this study, we coated plastic plates with gelatin in a concentration-dependent manner and assessed Young's modulus using atomic force microscopy (AFM) to investigate the microstructure of the surface of each plastic plate. The adhesion, proliferation, and differentiation of the ESCs were compared and analyzed revealing differences in surface microstructure dependent on coating concentration. Results: According to AFM analysis, there was a clear difference in the microstructure of the surface according to the presence or absence of the gelatin coating, and it was confirmed that there was no difference at a concentration of 0.5% or more. ES cell also confirmed the difference in cell adhesion, proliferation, and differentiation according to the presence or absence of gelatin coating, and also it showed no difference over the concentration of 0.5%. Conclusions: The optimum gelatin-coating for the maintenance and differentiation of ES cells is 0.5%, and the gelatin concentration-mediated microenvironment and ES cell signaling are closely correlated.

• Tribology and Lubricants
• /
• v.35 no.6
• /
• pp.362-368
• /
• 2019

In this study, mechanical and tribological properties were investigated by varying the process temperature (50, 100, 125 and 150℃) to reduce internal stress. The internal stress reduction by thermal dissociation ta-C coating film with increasing temperature is confirmed through the curvature radius of the ta-C coating according to the temperature of the SUS plate. As the coating temperature increased, the mechanical properties (hardness, modulus, toughness) deteriorated, which is in agreement with the Raman analysis results. As the temperature increased, the sp² phase ratio increased owing to the dissociation of the sp³ phase. The friction and wear properties are related to the process temperature during ta-C coating. Low friction and wear properties are observed in high hardness samples manufactured at 50℃, and wear resistance properties decreased with increasing temperature. The contact area is expected to increase owing to the decrease of hardness(72 GPa to 39 GPa) and fracture toughness with increasing temperature which accelerated wear because of the debris generated. It was confirmed that at process temperature of over than 100℃, the bond structure of the carbon film changed, and the effect of excellent internal stress was reduced. However, the wear resistance simultaneously decreased owing to the reduction in fracture toughness. Therefore, in order to increase industrial utilization, optimum temperature conditions that reduce internal stress and retain mechanical properties.

• Korean Journal of Materials Research
• /
• v.22 no.8
• /
• pp.416-420
• /
• 2012

Recently nanoscience and nanotechnology have been studied intensively, and many plants, insects, and animals in nature have been found to have nanostructures in their bodies. Among them, lotus leaves have a unique nanostructure and microstructure in combination and show superhydrophobicity and a self-cleaning function to wipe and clean impurities on their surfaces. Coating films with combined nanostructures and microstructures resembling those of lotus leaves may also have superhydrophobicity and self-cleaning functions; as a result, they could be used in various applications, such as in outfits, tents, building walls, or exterior surfaces of transportation vehicles like cars, ships, or airplanes. In this study, coating films were prepared by dip coating method using polypropylene polymers dissolved in a mixture of solvent, xylene and non-solvent, methylethylketon, and ethanol. Additionally, attempts were made to prepare nanostructures on top of microstructures by coating with the same coating solution with an addition of carbon nanotubes, or by applying a carbon nanotube over-coat on polymer coating films. Coating films prepared without carbon nanotubes were found to have superhydrophobicity, with a water contact angle of $152^{\circ}$ and sliding angle less than $2^{\circ}$. Coating films prepared with carbon nanotubes were also found to have a similar degree of superhydrophobicity, with a water contact angle of 150 degrees and a sliding angle of 3 degrees.

• Korean Journal of Materials Research
• /
• v.14 no.8
• /
• pp.558-564
• /
• 2004

In order to improve the low hardness and low wear resistance of Ti-6Al-4V alloy, plasma carburization treatment and CrN film coating were carried out. Effects of the plasma carburization and CrN coating were analyzed and compared with the non-treated alloy by mechanical and creep tests. After plasma carburization and CrN coating treatments, the carburized layer was about 150 ${\mu}m$ in depth and CrN coated layer was about 7.5 ${\mu}m$ in thickness. Hardness value of about $H_{v}$ 402 of the non-treated alloy was improved to $H_{v}$ 1600 and 1390 by plasma carburization and CrN thin film coating, respectively. Stress exponent(n) was decreased from 9.10 in CrN coating specimen to 8.95 in carburized specimen. However, the activation energy(Q) was increased from 242 to 250 kJ/mol. It can be concluded that the static creep deformation for Ti-6Al-4V alloy is controlled by the dislocation climb over the ranges of the experimental conditions.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.467-471
• /
• 2005

In this paper, experimental methods about the flow behavior of thin polymer film by various edge patterns in the spin coating process for stable cover layer coating of a blu-ray disc is described. The blu-ray disc, a next-generation optical disc format over 25GB, consists of a 1.1m thick substrate and a 0.1mm tick cover layer. Generally, cover layer on the blu-ray disc is made by the polymer spin coating process. However, it is hard to secure sufficient coating uniformity around the rim on the cover layer. In order to get the uniform thickness deviation and to minimize the bead around the rim, the edge of the disc substrate can be modified into various patterns, such as normal plain, trench, step and chamfer pattern, etc, around the rim on the disc and experimented with various parameters, such as surface tension, viscosity, coating time, temperature and rotation speed, etc. And the optimal shape of the rim was tried to get by 3 dimensional computer simulation of the polymer expulsion process.