• 한국음향학회지
• /
• 제23권4호
• /
• pp.303-308
• /
• 2004

본 논문에서는 전력 증폭기의 선형화를 위해 제안된 feed-forward 선형화 방식을 IMT-2000용 송신 시스템에 적용한 새로운 송신 시스템 구조를 제안한다. 이 시스템에서 feed-forward 구조는 왜곡 성분을 비교하고 제거하기 위해 보조신호(reference signal)을 필요로 하는데, 이 보조신호는 무시할 정도로 낮은 왜곡을 갖도록 낮은 입력 동작 범위에서 동작하는 두 번째 변조기에서 만들어 진다. 이런 구조로 한 결과송신 시스템에서 증폭기뿐만 아니라 변조기의 왜곡을 줄일 수 있다는 큰 장점이 있다. 본 논문의 시스템은 Agilent 社의 EEsoft ADS ver.2002를 사용하여 설계하였으며, 입력은 1.98GHz 주파수 대역에서 2MHz의 주파수 간격을 갖는 2-tone으로 하였고, 약 49.95dB의 IMD 개선 특성을 얻어, 본 논문에서 제안하는 시스템은 간단함과 선형성을 동시에 제공할 수 있다는 것을 입증하였다.

• 상하수도학회지
• /
• 제26권6호
• /
• pp.825-831
• /
• 2012

The retrofitting of a thickening unit process is widely considered in municipal wastewater treatment plants in Korea to enhance the anaerobic digestion efficiency. The authors examined the effect of feed concentration (2-34.1 g VS/L) and feed to microorganism (F/M) ratio (0.50-1.35 g VS/g VS) on anaerobic batch digestion of sewage sludge. Methane yield over 90 mL $CH_4/g$ $VS_{feed}$ was found at a feed concentration in the range of 12-26 g VS/L and a F/M ratio below 0.6 g VS/g VS. A high F/M ratio decreased methane yield and rate with oragnic acid accumulation. As sudden increase of sewage sludge concentration prior to anaerobic digestion would jeopardize the digester performance due to the rasied F/M ratio, gradual increase of the sludge feed concentration or an additional biomass retention in the digester is recommended.

• Asian-Australasian Journal of Animal Sciences
• /
• 제14권4호
• /
• pp.553-558
• /
• 2001

The effect of poor feather cover on feed intake and production was examined in two commercial strains of layers (tinted and brown egg) over 91-98 weeks of age. Hens were housed at four per cage ($600cm^2/bird$) in a commercial layer shed which ranged in temperature from 13.2 to $16.8^{\circ}C$. At the start of the experiment 50% of the birds were classified as having poor feather cover. Feather score was highly correlated with feed intake. Poor feather cover on the neck and the back were the best indicators of hens with high feed intake. Feed intake of hens with poor feather cover was 16% higher (p<0.05) than hens with good feather cover. Hens with good feather cover produced more eggs (p<0.05) early in the trial and had a higher (p<0.05) liveweight, but there was no significant differences in egg weight. Feed per dozen eggs was superior (p<0.05) in hens with good feather cover. Feather cover on the back and vent were the best indicators of overall feather score, while the tail, base of tail and vent were the body parts most affected in birds with poor feather cover.

• Asian-Australasian Journal of Animal Sciences
• /
• 제28권4호
• /
• pp.519-529
• /
• 2015

The aims of this study were to determine the effects of feeding medium-roasted soybean meal (SBM) and corn dried distiller's grains with solubles (CDDGS) in dairy cows on milk production and income over feed costs. A randomized complete block design experiment was conducted with 24 crossbred multiparous Holstein Friesian dairy cows in early- and mid-lactation. Four dietary treatments were as follows: basal diet without feed substitute (Control), 7.17% dry matter (DM) roasted SBM replaced for concentrate (R-SBM), 11.50% DM CDDGS replaced for concentrate (DDGS), and 3.58% DM roasted SBM plus 5.75% DM CDDGS replaced for concentrate (SB-DG). The roasted SBM was produced using a medium-heated treatment at $100^{\circ}C$ for 180 min. Dry matter intake was not affected by feeding high rumen undegradable protein (RUP) sources, but the replacement of roasted SBM and CDDGS for concentrate significantly improved (p<0.001) RUP intake (0.90, 0.86, and 0.88 kg/d corresponding to R-SBM, DDGS, and SB-DG) compared to the control (0.61 kg/d). Feeding roasted SBM and CDDGS alone or in combination had no significant effect on milk composition of dairy cows (p>0.05), whereas milk yield was significantly increased by 3.08 kg/d in the SB-DG group relative to the control group (p<0.01). Net income was meaningfully increased (p<0.05) from 4th week post feeding, the SB-DG group reached the greatest net income ($3.48/head/d) while the control group had the lowest value ($2.60/head/d). In conclusion, the use of CDDGS alone or in combination with medium-roasted SBM as substitute for concentrate in lactating dairy cattle diet led to improved milk production and net income over feed costs without affecting total dry matter intake and milk composition, while feeding medium-roasted SBM seemed to show intermediate values in almost parameters.

• Asian-Australasian Journal of Animal Sciences
• /
• 제22권5호
• /
• pp.674-680
• /
• 2009

The objective of this study was to investigate antimicrobial activity, during the storage period, of animal feed and any effects on in vitro rumen digestion by supplementing different levels (5.55, 11.1, and 22.2 g/kg) of freeze dried citrus peel (FDCP) to the feed compared to untreated feed and feed treated with an antifungal agent (AA) at 0.05 g/kg. In a preservation test, feed supplemented with FDCP showed no deterioration over 21 days. Untreated feed and AA-treated feed, however, showed signs of deterioration after 16 days storage. Yellow colour and red colour, measured by spectro chromameter, decreased in the untreated and AA-treated feeds, but not in feed supplemented with FDCP. Aflatoxin was detected in untreated and AA-treated feeds at 16 days (8 ppb and 2 ppb) and 21 days (8 ppb and 4 ppb), but aflatoxin was not detected in the feed supplemented with FDCP. In a second experiment, fermentation by rumen microorganisms of FDCP (22.2 g/kg) and AA (0.05 g/kg) supplemented feeds was studied in vitro. Feeds were incubated with buffered rumen fluid for 3, 6, 9, 12, 24, and 48 h. Dry matter digestibility (DMD) and organic matter digestibility (OMD) were affected by treatment, but ammonia-N, total, and individual volatile fatty acids (VFA) were not adversely affected by treatment. In conclusion, the results indicated that FDCP might be useful for inhibiting microbial growth of animal feed during storage without disrupting rumen fermentation.

• Journal of Biosystems Engineering
• /
• 제6권1호
• /
• pp.60-72
• /
• 1981

This study was carried out to find out the effects of the sheaf size of paddy harvested by the binders on the threshing performance, load characteristics and power requirement of an auto-feed thresher. The results of the study are summarized as follows: 1. The seperating performance of the thresher appeared to be satisfactory for all the sheaf sizes although the amount of rubbishes and empty grains slightly increased with the sheaf size of paddy. 2. There was no significant difference in grain output quality of the thresher among the three sheaf sizes. However, the amount of grains left unthreshed increased with the sheaf size. In the case of the largest sheaf size with the feed rate of 780kg/h, it exceeded the limit set by the national inspection regulations. 3. The position of the feed-chain rail gave a significant effect on the power requirement of the thresher. At the feed rate of 780kg/h, the net power required to convey sheafs through the feed chain was in the range of 0.37 to 0.50 PS for the middle and lowest position of feed-chain rail, and there was no significant difference among the sheaf sizes. At the highest position, however, it appeared that the smallest sheaf required more power than the others. The net power requirements at this position were 1.03, 0.59. 0.65 PS for the smallest, medium and largest sheafs respectively. 4. The torques of both the thresher and the engine shaft increased with the feed rate and were not affected by the sheaf size for the lower two feed rates of 520 and 780kg/h. At the highest feed rate of 1,040 kg/h, however, they were affected by the sheaf size. In this case, the medium sheaf size gave lower values than the others. 5. The variations in the thresher and the engine torque increased with the feed rate and were not affected by the sheaf size for the feed rate of 520kg/h. At the feed rate of 780kg/h, however, they increased with sheaf size. And at the feed rate of 1,040 kg/h, the torque variations increased greatly for all the sheaf sizes due to an over-load operating condition. 6. It appeared that the average and maximum power requirements of the thresher increased with the feed rate. But, there was no significant difference in power requirement among the sheaf sizes for the lower two feed rates. 7. The threshing efficiency of the thresher was in the range of 214-249 kg/ps.h with the feed rates of 520 and 780 kg/h, and it was not affected by both the sheaf size and the feed rate. At the feed rate of 1,040 kg/h, however, it decreased to as low as 171-174 kg/ps.h because of a sudden increase in power requirement. 8. The average power requirements of the engine were slightly higher than those of the thresher due to the slippage of flat belt between the thresher and engine. It appeared that power transmission from the engine to the thresher was maintained properly since slippages were moderately low with the range of 2.78 to 6.51% throughout the tests. 9. The specific fuel consumption of the engine (diesel 8PS) decreased as the feed rate increased. However, there was no significant reduction in specific fuel consumption as the feed rate increased above 780 kg/h.

• Asian-Australasian Journal of Animal Sciences
• /
• 제4권3호
• /
• pp.227-230
• /
• 1991

A comparative study was conducted in total thirty six large while weaner pigs of about 15 kg body weight namely boars, barrows and gilts to evaluate best sex and economic slaughter weight with one standard ration. In 159 days study period feed consumption, growth, feed conversion ratio and carcass quality were judged in all sexes of pigs at 50, 70 and 90 kg body weight. It was noted that upto 70 kg body weight the growth in boars and gills 46.0 and 49.0 kg and feed conversion ratio 4.83 and 4.81 were superior and economical over the barrows, which were 45.5 kg and 4.95. Later on there were too many fluctuations in growth and feed conversion ratio in all sexes of pigs, which would be uneconomical. Carcass quality was also better in boars and gilts than barrows, No boar taint was noted in most of the boar carcasses. Hence it is concluded that boars and gilts can be raised upto the 70 kg body weight for economic pork production.

• 한국자동차공학회논문집
• /
• 제15권6호
• /
• pp.30-37
• /
• 2007

The injection and spray characteristics of top-feed type injector was investigated under liquid phase injection fueled with liquefied petroleum gas (LPG). Different pressures and temperatures of fuel injection system were tested to identify the injection characteristics after hot soaking. MIE-scattering technique was used for verification of successful liquid phase injection after hot soaking. In case of bottom-feed type injector, the injection was accomplished at every experimental condition. In case of top-feed type injector, when the pressure of LPG was over 1.2 MPa, the injection was not executed. However, under the pressure were 1.2 MPa, the liquid phase injection after hot soaking was accomplished. The engine with top-feed type fuel injection equipment was restarted successfully after hot soaking.

• 한국기계가공학회지
• /
• 제19권4호
• /
• pp.71-78
• /
• 2020

The rotary feed axes of a 5-axis machine tool can increase the freedom of the tool posture, while reducing feed speed and rigidity. In addition, as a ball-end mill is inevitably used during machining by rotational feed, the step-over length is reduced compared to the flat-end mill, thereby reducing the material removal rate. Therefore, this study attempts to improve the material removal rate, feed speed, and machining stability using the corner radius flat-end mill and a fixed controlled machining method for the rotary feed axes during roughing. In addition, the tapered ball-end mill and simultaneously controlled machining method for the rotary feed axes were used for finishing to improve the propeller's 5-axis machining efficiency by enhancing the surface quality. In order to create the tool path effectively and easily, we propose a specific approach for using the propeller's geometric properties and evaluate the effectiveness of the proposed method by comparing it with the method of the dedicated module.

• Journal of Microbiology and Biotechnology
• /
• 제32권3호
• /
• pp.269-277
• /
• 2022

Human activities account for approximately two-thirds of global methane emissions, wherein the livestock sector is the single massive methane emitter. Methane is a potent greenhouse gas of over 21 times the warming effect of carbon dioxide. In the rumen, methanogens produce methane as a by-product of anaerobic fermentation. Methane released from ruminants is considered as a loss of feed energy that could otherwise be used for productivity. Economic progress and growing population will inflate meat and milk product demands, causing elevated methane emissions from this sector. In this review, diverse approaches from feed manipulation to the supplementation of organic and inorganic feed additives and direct-fed microbial in mitigating enteric methane emissions from ruminant livestock are summarized. These approaches directly or indirectly alter the rumen microbial structure thereby reducing rumen methanogenesis. Though many inorganic feed additives have remarkably reduced methane emissions from ruminants, their usage as feed additives remains unappealing because of health and safety concerns. Hence, feed additives sourced from biological materials such as direct-fed microbials have emerged as a promising technique in mitigating enteric methane emissions.