• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.270-273
• /
• 1996

This paper describes a type of piezoelectric transformer with improved design principles. It consists of a thin rectangular piezoelectric ceramic plate having two input electrodes and one output electrode. The length of each input and output electrode is nearly one third of that of piezoelectric transformer itself. In the driving section, the ceramic plate is poled in the thickness direction reversely with each other, and has electrodes on both main faces. The electric input near its fundamental resonance frequency is applied to the driving section in parallel and the output voltage from the generating section is connected to the resistor load. Its equivalent circuit is derived from the Mason\`s model. The frequency characteristics near the resonance frequency under no load have been investigated. Moreover, using this piezoelectric transformer we measured the LCD backlight characteristics.

• Geomechanics and Engineering
• /
• v.6 no.6
• /
• pp.613-624
• /
• 2014

The fractures in coal are the main migration and output channels of coalbed methane, directly influencing the permeability of the coal seams. It is of great significance to study the effect of fracture distribution in coals on the permeability of coal seam. The development rules of endogenetic and exogenetic fractures are different among various coal lithotypes. There is also difference in the fracture density for the same lithotype with different thicknesses. Through the observation and description of the macroscopic fractures in coal and the origin of fractures in coal, the effect of the coal lithotype and its thickness on fracture development in coal was discussed. It was found through the study that the density of fractures in vitrain band was the maximum for the same coal rank and thickness, followed by clarain band. There were few fractures developed in the durain band. However, the changes of fracture density in three types of bands presented different declining trends for low, medium and high coal rank. There were no fractures developed in the fusain. There were three variation patterns for the fracture densities at the same coal rank and coal lithotype: linear decrease, nonlinear decrease, and first decrease then remaining unchanged. However, the overall trend was that the fracture density decreased with the increase of thickness of coal band for the same coal rank and coal lithotype.

• Journal of Sensor Science and Technology
• /
• v.20 no.2
• /
• pp.114-117
• /
• 2011

A thick 25 ${\mu}m$ thickness poled P(VDF/TrFE) film pyroelectric infrared ray sensor has been fabricated and then thin 1.6 ${\mu}m$ thickness P(VDF/TrFE) film pyroelectric infrared ray sensor has been fabricated also. These thick and thin P(VDF/TrFE) film pyroelectric infrared ray sensor was mounted in TO-5 housing to detect infrared light of 5.5 ~ 14 ${\mu}m$ wavelength for human body detecting with each other. The noise output voltage of the thick P(VDF/TrFE) film pyroelectric infrared ray sensor were 380 mV and NEP(noise equivalent power) is $3.95{\times}10^{-7}$ W which is the similar value with the commercial pyroelectric infrared ray sensor using ceramic materials as a sensing material. The NEP and specific detectivity $D^*$ of the thin P(VDF/TrFE) film pyroelectric infrared ray sensor were $2.13{\times}10^{-8}$ W and $9.37{\times}106$ cm/W under emission energy of 13 ${\mu}W/cm^2$ respectively. These result caused by lower thermal diffusion coefficient of a thin 1.6 ${\mu}m$ thickness PVDF/TrFE film than the thick 25 ${\mu}m$ thickness poled P(VDF/TrFE) film pyroelectric infrared ray sensor.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.2
• /
• pp.70-73
• /
• 2017

We investigated n-i-p type single junction hydrogenated amorphous silicon oxide solar cells. These cells were without front surface texture or back reflector. Maximum power point efficiency of these cells showed that an optimized device structure is needed to get the best device output. This depends on the thickness and defect density ($N_d$) of the active layer. A typical 10% photovoltaic device conversion efficiency was obtained with a $N_d=8.86{\times}10^{15}cm^{-3}$ defect density and 630 nm active layer thickness. Our investigation suggests a correlation between defect density and active layer thickness to device efficiency. We found that amorphous silicon solar cell efficiency can be improved to well above 10%.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.8
• /
• pp.57-62
• /
• 1993

In this paper, both feasible power gain and power added efficiency at the operating center frequency of 12 GHz are stressed to design a power FET with double-heterjunction structure. The variable parameters or the design are the unit gate width, the gate length, the doping density of AlGaAs, the AlGaAs thickness, the spacer thickness, the Al mole fraction, and the GaAs well thickness. The results of simulation for the FET with 1.mu.m gate length show that the power gain and the power added efficiency are 10.2 dB and 36.3% at 12GHz, respectively. An extrapolation of the relation between current gain and unilateral gain yields a 17 GHz cutoff frequency and 43GHz maximum frequency of oscillation. The calculation of the current versus voltage characteristics show that the output power of the device is about 0.62W.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.693-696
• /
• 2003

Among many servo control systems in steel making plant, AGC system in hot rolling mill is very important to get a accurate strip thickness for good quality. AGC (Auto Gauge Control) system controls the roll gap to maintain the required thickness by using the variation of roll force and the measure of output thickness. In this paper, a simulator of AGC system which unifies both hydraulic servo control system and AGC algorithm is suggested. After proving the concurrence of algorithms between the simulator and real system, main actuator system is added. Instead of usual PI system used in present system, DOB control scheme is applied and shows the effect of disturbance attenuation well.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.10 no.1
• /
• pp.90-95
• /
• 2014

Local wall thinning is a point of concern in almost all steel structures such as pipe lines covered with a thermal insulator made up of materials with low thermal conductivity(fiberglass or mineral wool); hence, Non Destructive Technique(NDT) methods that are capable of detecting the wall thinning and defects without removing the insulation are necessary. In this study we developed a Pulsed Eddy Current(PEC) system to detect the wall thinning of Ferro magnetic steel pipes covered with fiber glass thermal insulator and shielded with Aluminum plate. The developed system is capable of detecting the wall thickness change through an insulation of thickness 10cm and 0.4mm aluminum shielding. In order to confirm the thickness change due to wall thinning, two different sensors, a hall sensor and coil sensor were used as a detecting element. In both cases, the results show a very good change corresponding to the thickness change of the test specimen. During these experiments a carbon steel tube of diameter 210mm and a length of 620mm, which is covered with insulator of 95mm thickness was used. To simulate the wall thinning, the thickness of the tube is changed for a specified length such as 2.5mm, 5mm and 8 mm from the inner surface of the tube. A 0.4mm thick Aluminum plate was covered on the Test specimen to simulate the shielding of the insulated pipelines. For both hall sensor and coil detection methods Fast Fourier transform(FFT) was calculated using window approach and the results for the test specimen without Aluminum shielding were summarized which shows a clear identification of thickness change in the test specimen by comparing the magnitude spectra. The PEC system can detect the wall thinning under the 95 mm thickness insulation and 0.4 mm Al shielding, and the output signal showed linear relation with tube wall thickness.

• Journal of the Korean Society of Radiology
• /
• v.4 no.3
• /
• pp.5-11
• /
• 2010

In this paper, we are suggested development of dual-mode detector for dual-energy digital radiography. Design of dual-energy radiography module for commercial BIS (Baggage Inspection System) is used in the spectrum of the X-ray generator and detector for dual-mode features and radiological characteristics were analyzed. BIS suggestl on the image detector module being used to target X-ray tube to simulate X-ray spectrum and simulated spectrum to offer through the new radiographic characteristics of the detector modules were investigated. Using X-ray experiments with an increase in the thickness of the copper filter low energy detector (LED) and high-energy detector (HED) as the difference between the output signal increases. HED, especially in the size of the output signal decreases with increasing thickness of the copper filter was found.

• Korean Journal of Optics and Photonics
• /
• v.8 no.5
• /
• pp.395-402
• /
• 1997

We have obtained the optimum thickness of anti-reflection(AR) coating on one of facets of a $\1.55mu\textrm{m}$ InGaAsP MQW FP semiconductor laser by in-site monitoring of the light emitted from the rear facet during the film deposition on the fore facet. The optimum thickness of $SiO_x$ thin film whose refractive index is 1.85 was found to be 188 nm. The reflectivity of the coated facet was calculated by the threshold current ratio of before and after AR coating, which was obtained from exprimental data, and it was about 2$\times$ $10^{-4}$. The results show that the output power is increased by 87% at bias current 60 mA, the slope efficiency is increased by 3.4 times, and the threshold current is increased by 2.64 times. By in-situ depositing of the $Si/SiO_2$ thin film HR coating on the rear facet, the output power was increased by 160% than before the AR and HR coatings, the slope efficiency was increased by 3.8 times, the threshold current was increased by 1.07 times, which is similar to the value of before AR coating. Due to the AR and HR coatings the output light power characteristics were enhanced.

• Korean Journal of Materials Research
• /
• v.34 no.1
• /
• pp.34-43
• /
• 2024

New piezoelectric and triboelectric materials for energy harvesting are being widely researched to reduce their processing cost and complexity and to improve their energy conversion efficiency. In this study, BaTiO₃ films of various thickness were deposited on Ni foams by R.F. magnetron sputtering to study the piezoelectric and triboelectric properties of the porous spongy structure materials. Then piezoelectric nanogenerators (PENGs) were prepared with spongy structured BaTiO₃ and PDMS composite. The output performance exhibited a positive dependence on the thickness of the BaTiO₃ film, pushing load, and poling. The PENG output voltage and current were 4.4 V and 0.453 ㎂ at an applied stress of 120 N when poled with a 300 kV/cm electric field. The electrical properties of the fabricated PENG were stable even after 5,000 cycles of durability testing. The triboelectric nanogenerators (TENGs) were fabricated using spongy structured BaTiO₃ and various polymer films as dielectrics and operated in a vertical contact separation mode. The maximum peak to peak voltage and current of the composite film-based triboelectric nanogenerator were 63.2 V and 6 ㎂, respectively. This study offers new insights into the design and fabrication of high output nanogenerators using spongy structured materials.