• Journal of Sensor Science and Technology
• /
• v.15 no.1
• /
• pp.34-39
• /
• 2006

This study provides the electrical model of combustible catalytic gas sensor. Physical characteristics such as thermal behavior, resistance change were included in this model. The finite element method analysis for sensor device structure showed that the thermal behavior of sensor is expressed in a simple electrical equivalent circuit that consists of a resistor, a capacitor and a current source. This thermal equivalent circuit interfaces with real electrical circuit using two parts. One is 'power to heat' converter. The other is temperature dependent variable resistor. These parts realized with the analog behavior devices of the SPICE library. The gas response tendency was represented from the mass transferring limitation theory and the combustion theory. In this model, Gas concentration that is expressed in voltage at the model, is converted to heat and is flowed to the thermal equivalent circuit. This model is tested in several circuit simulations. The resistance change of device, the delay time due to thermal capacity, the gas responses output voltage that are calculated from SPICE simulations correspond well to real results from measuring in electrical circuits. Also good simulation result can be produced in the more complicated circuit that includes amplifier, bios circiut, buffer part.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.9
• /
• pp.4398-4417
• /
• 2017

Multi-user Multiple-Input and Multiple-Output (MU-MIMO) has potential for prominently enhancing the capacity of wireless network by simultaneously transmitting to multiple users. User selection is an unavoidable problem which bottlenecks the gain of MU-MIMO to a great extent. Major state-of-the-art works are focusing on improving network throughput by using Channel State Information (CSI), however, the overhead of CSI feedback becomes unacceptable when the number of users is large. Some work does well in balancing tradeoff between complexity and achievable throughput but is lack of consideration of fairness. Current works universally ignore the rational utilizing of time resources, which may lead the improvements of network throughput to a standstill. In this paper, we propose TOUSE, a scalable and fair user selection scheme for MU-MIMO. The core design is dynamic-time-warping-based user selection mechanism for downlink MU-MIMO, which could make full use of concurrent transmitting time. TOUSE also presents a novel data-rate estimation method without any CSI feedback, providing supports for user selections. Simulation result shows that TOUSE significantly outperforms traditional contention-based user selection schemes in both throughput and fairness in an indoor condition.

• Journal of Internet Computing and Services
• /
• v.15 no.4
• /
• pp.119-124
• /
• 2014

Blind adaptive systems based on the Euclidean distance (ED) between the distribution function of the output samples and that of a set of random symbols generated at the receiver matching with the distribution function of the transmitted symbol points estimate the ED at each iteration time to examine its convergence state or its minimum ED value. The problem is that this ED estimation obtained by block?data processing requires a heavy calculation burden. In this paper, a recursive ED estimation method is proposed that reduces the computational complexity by way of utilizing the relationship between the current and previous states of the datablock. The relationship provides a ground that the currently estimated ED value can be used for the estimation of the next ED without the need for processing the whole new data block. From the simulation results the proposed recursive ED estimation shows the same estimation values as that of the conventional method, and in the aspect of computational burden, the proposed method requires only O(N) at each iteration time while the conventional block?processing method does $O(N^2)$.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.11a
• /
• pp.171-171
• /
• 2012

In this study, we fabricated the high-brightness AlGaInP-based red light emitting diodes (LED)s using by direct printing technique and inductive coupled plasma (ICP) reactive ion etching (RIE). In general, surface roughening was fabricated by wet etching process to improve the light extraction efficiency of AlGaInP-based red LED. However, a structure of the surface roughening, which was fabricated by wet etching, was tiled cone-shape after wet etching process due to crystal structure of AlGaInP materials, which was used as top-layer of red LED. This tilted cone-shape of surface roughening can improve the light extraction of LED, but it caused a loss of the light extraction efficiency of LED. So, in this study, we fabricated perfectly cone shaped pattern using direct printing and dry etching process to maximize the light extraction efficiency of LED. Both submicron pattern and micron pattern was formed on the surface of red LED to compare the enhancement effect of light extraction efficiency of LEDs according to the diameter of sapphire patterns.After patterning process using direct printing and ICP-RIE proceeded on the red LED, light output was enhanced up to 10 % than that of red LED with wet etched structure. This enhancement of light extraction of red LED was maintained after packaging process. And as a result of analyze of current-voltage characteristic, there is no electrical degradation of LED.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.4C
• /
• pp.371-379
• /
• 2002

In this paper, the MMIC SPST switches operating from DC to 3GHz were designed and implemented. Prior to the design of switches, the small and large-signal switch models were needed to predict switch performance accurately. The newly proposed small-signal switch model parameters were extracted from measured S-parameters using optimization technique with estimated initial values and boundary limits. In the extraction of large-signal switch model parameters, the current source was modeled by fitting empirical equations to measured DC data and the charge model was derived from extracted channel capacitances from measured S-parameters varying the drain-source voltage. To design basic series-shunt SPST switches and isolation-improved SPST switches, we applied this model to commercial microwave circuit simulator. The improved SPST switches exhibited 0.302dB insertion loss, 35.762dB isolation, 1.249 input VSWR, 1.254 output VSWR, and about 15.7dBm PldB with 0/-3V control voltages at 3GHz.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.3
• /
• pp.784-794
• /
• 1996

In this papre, the design and the fabrication of the surface mountable voltage controlled oscillator is described for local oscillator in PCS(WACS/TDMA) handset. The VCO employs two silicon bipolar transistors of $f_{gamma}$ of 4 GHz as active devices. These are asembled to form the VCO on the 4 layer PCB of the size $12{\times}10mm$which provides the strip line resonator at the third layer. The fabricated VCO shows tuning rage over 50 MHz, phase noise -100 dBc/Hz at the 100 kHz frequency offset, and 0 dBm output power with the consumption of 22 mA at 3V. It is belived that the size will be more reduced by employing 1005 chip components and that the current consumption will be improved by employing transistors of higher $f_{gamma}$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.6
• /
• pp.1602-1609
• /
• 1998

In this paper, the design and implementation of the novel RF front end circuit for CDMA based PCS phone is described. This novel scheme is realized by building the power amplifier module combined with duplexer. The dielectric filters which are parts of duplexer are broken up and relocated into the module. Electromagnetic analysis for via holes and coupling between narrow transmissio lines is icluded to design a circuit. The combined moule has been minimaturized to be as small as 1.5CC. It has satisfied IS-95 requirements for linearity performances of CDMA signal at 24-dBm output power as well as played apart as a duplexer. The operating current of about 95mA has been saved owing to both rearranging dielectric filters and limiting operating point to class-B by considering real working power range of CDMA phones.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.6
• /
• pp.293-298
• /
• 2007

The aged are faced with increasing risk for falls. The aged have more fragile bones than others. When falls occur, it is important to detect this emergency state because such events often lead to more serious illness or even death. A implementation of PDA system, for detection of emergency situation, was developed using 3-axis accelerometer in this paper as follows. The signals were acquired from the 3-axis accelerometer, and then transmitted to the PDA through a Bluetooth module. This system can classify human activity, and also detect an emergency state like falls. When the fall occurs, the system generates the alarm on the PDA. If a subject does not respond to the alarm, the system determines whether the current situation is an emergency state or not, and then sends some information to the emergency center in the case of an urgent situation. Three different studies were conducted on 12 experimental subjects, with results indicating a good accuracy. The first study was performed to detect the posture change of human daily activity. The second study was performed to detect the correct direction of fall. The third study was conducted to check the classification of the daily physical activity. Each test lasted at least 1 min. in the third study. The output of the acceleration signal was compared and evaluated by changing various postures after attaching a 3-axis accelerometer module on the chest. The newly developed system has some important features such as portability, convenience and low cost. One of the main advantages of this system is that it is available at home healthcare environment. Another important feature lies in its low cost of manufacture. The implemented system can detect the fall accurately, so it will be widely used in emergency situations.

• Journal of Aquaculture
• /
• v.16 no.1
• /
• pp.44-50
• /
• 2003

This study aimed to develop the methods of growing Enteromorpha prolifera natural seedlings in its natural habitat and artificial indoor seedlings by inducing spore release. Likewise, the study examined the possibility of mass production by developing cultivation techniques with cultivating examination. The natural seedling of E.prolifera thrived in a sea area composed of sand and mud, which Is its natural habitat. Growing of this alga on the seedling frame 20 cm high from the bottom at the intertidal zone in summer and 40 cm high in fall was found to be very effective. However, enabling the best attachment rate for artificial indoor seedling requires inducing spore release after drying the mature thalli in a dark place fur about 12∼24 hours and setting seedling nets in a dark water tank (spore solution) for 24 hours. Breeding E.prolifera in a pole-system farm is best done in shallow sea areas with mud or mud and sand geological feature. However, floating-system lam is better for deep-sea areas with fast current. Ideal farming places are sea areas with plenty of nutritional salt and safe places that protect the lam facilities against billows. Furthermore, an exposure method on seawater surface to produce larger output should be used.

• Journal of the Korean Society for Railway
• /
• v.13 no.3
• /
• pp.304-308
• /
• 2010

This paper presents a methodology for identifying track irregularity using a wavelet transfer function. An equivalent wavelet SISO (single-input single-output) transfer function is defined by the measured track geometry and the acceleration data measured at a bogie of a train. All the measured data with various sampling frequencies were rearranged according to the constant 25cm reference recording distance of the track recording vehicle used in the field. Before applying the wavelet transform, measured data were regressed by eliminating those out of the range. The inverse wavelet transfer function is also formulated to estimate track geometry. The closeness of the estimated track geometry to the actual one is evaluated by the coherence function and also by FRF (frequency response function). A track irregularity index is defined by comparing the variance of the estimation error from the intact condition and that from the current condition. A simulation study has been carried out to examine the proposed algorithm.