• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.11
• /
• pp.12-20
• /
• 2002

Serially concatenated multilevel coded modulation (SCMCM) is proposed in this paper. It is a combined scheme of the outer convolutional code and inner multilevel coded modulation (MCM) which is bandwidth-efficient coded modulation. And the performance of three schemes for decoding of the proposed SCMCM is compared and analyzed. As results of simulations, global iterative decoding with inner and outer code should be performed to improve the error performance as the number of iterations is increased. And the scheme which uses both local iterative multistage decoding in MCM and global iterative decoding with inner and outer code, called Scheme 3 in this paper, shows the best error performance among the three schemes considered in this paper. In addition, performance difference between this scheme and the others is increased as the signal to noise ratio (SNR) is increased. Therefore, Scheme 3 is considered to be the proper decoding scheme of SCMCM.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.2C
• /
• pp.139-147
• /
• 2010

A novel turbo coded modulation scheme, called turbo-APPM, for deep space optical communications is constructed. The constructed turbo-APPM is a serial concatenations of turbo codes, an accumulator and a pulse position modulation (PPM), where turbo codes act as an outer code while the accumulator and the PPM act together as an inner code. The generator polynomial and the puncturing rule for generating turbo codes are chosen to show the low bit error rate. At the receiver, the joint decoding is performed by exchanging soft information iteratively between the inner decoder and the outer decoder. In the outer decoder, a local iterative decoding for turbo codes is conducted before transferring soft information to the inner decoder. Poisson distribution is used to model the deep space optical channel. It is shown by simulations that the constructed turbo-APPM provides coding gains over all previously proposed schemes such as LDPC-APPM, RS-PPM and SCPPM.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.4
• /
• pp.94-103
• /
• 1993

In this work, the imaginary part of the inner modulation transfer function of the cutting dynamics is introduced for tool wear monitoring. Time-series method is utilized to construct the general three dimensional cutting dynamics whose imaginary part of the inner modulation transfer funcition shows the proportionality to tool wear at the natural frequency of the machine tool dynamics. Thus model is reduced to single-input single-output model without altering the proportionality characteristics to tool wear and implemented to the dual computer system in which one computer performs measurement while the other calculates the imaginary part of the inner modulation transfer function of the cutting dynamics by the batch least square method. The values of the imaginary part at the natural requency of the machine tool structure in the cutting direction are compared to the one calculated during machining with a brand new tool to decide the current status of the tool. The experiments shows the relevance of the proposed concept.

• Proceedings of the KIEE Conference
• /
• 1999.07f
• /
• pp.2529-2533
• /
• 1999

This paper proposes a modified hysteresis current control method based on space vector modulation. The proposed method differs from former works in that it uses effective voltage vectors instead of zero vectors while not significantly increasing the circuit complexity. The circuit uses outer band that is slightly wider than the usual current limit band (inner band) to detect the phase of current command and thereby the region information. The comparator output signals associated with the inner and outer band are used to determine the proper voltage vector that minimizes the current error and number of switching, with simple logic circuitry. The utilization of effective voltage vector is of particular importance when the ac-side emf is relatively large. Both the simulation and experiment show that the proposed method is more effective than the conventional one that uses zero vectors, in reducing the number of switching over a range of ac-side emf variation.

• Journal of Power Electronics
• /
• v.14 no.5
• /
• pp.937-945
• /
• 2014

This paper presents an optimized space vector pulse-width modulation (OSVPWM) technique for a five-level cascaded H-bridge (CHB) inverter. The space vector diagram of the five-level CHB inverter is optimized by resolving it into inner and outer two-level space vector hexagons. Unlike conventional space vector topology, the proposed technique significantly reduces the involved computational time and efforts without compromising the performance of the five-level CHB inverter. A further optimized (FOSVPWM) technique is also presented in this paper, which significantly reduces the complexity and computational efforts. The developed techniques are verified through MATLAB/SIMULINK. Results are compared with sinusoidal pulse-width modulation (SPWM) to prove the validity of the proposed technique. The proposed simulation system is realized by using an XC3S400 field-programmable gate array from Xilinx, Inc. The experiment results are then presented for verification.

• Journal of ILASS-Korea
• /
• v.14 no.2
• /
• pp.59-64
• /
• 2009

These experiments are close examination of spray characteristics that are continuous liquid jet and modulated liquid jet. The experiments were conducted using water, over a range of crossflow velocities from $42{\sim}l36\;m/s$, with modulation frequencies of $35.7{\sim}166.2\;Hz$. Between continuous crossflow jet and modulated cross-flow jet of penetration, breakup point, spray angle and macro spray shape are experimentally investigated with image analysis. In cross-flow field, main parameter of liquid jet for breakup was cross-flow stream rather than modulation effect. As oscillation of the periodic pressure that could make liquid jet moved up and down, the mixing efficiency was increased. Also, a bulk of liquid jet puff was detected at upper field of liquid surface. So, this phenomenon has a good advantage of mixing spray from concentration of center area to outer area. Because of modulation frequency, SMD inclination of the structured layer was evanescent. Cross-sectional characteristics of SMD at downstream area were non-structured distributions. Then cross-sectional characteristics of SMD size were about same tendency over a range that is effect of spray mixing. The tendency of volume flux value for various modulation frequency was same distribution. And volume flux was decreased when the modulation frequency increase.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.4A
• /
• pp.519-527
• /
• 2000

This paper suggests and analyzes the Serially Concatenated Space-Time Code(SCSTC) with the possibility of a efficient high-speed transmission in a band limited channel. The suggested code has a structure that uses the interleaver to connect the space-time code as an inner code and the convolutional code as a outer code serially. This code keeps the advantage of high-speed transmission and also has the high BER performance. The performance of the suggested system is compared with the conventional bandwidth efficient trellis coded modulation, such as a Serially Concatenated Trellis Coded Modulation (SCTCM) and a Turbo-Trellis Coded Modulation(Turbo-TCM). The results show that the suggested system has a 2.8dB and 3dB better BER performance than SCTCM and Turbo-TCM respectively in case of the transmission rate 2b/s/Hz in fading channel.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.57 no.4
• /
• pp.356-361
• /
• 2008

The conventional drive system of SRM has a current sensor per each phase. The torque demand signal generated by the outer control loop is translated into individual current reference signal for each phase. The torque is controlled by regulating these currents. Using the SRM in a variable-speed control, the phase currents are generally regulated to achieve a square wave. The simplest form of current regulation uses fixed frequency delta modulation of the phase voltages. The aim of this paper is to regulate 3-phases current of SRM by only single current sensor using delta modulation with digital chip. In this paper, the asymmetric bridge converter which is able to control independently phases and be excited simultaneously is used as the driver system for 6/4 poles SRM. And the current sensor is replaced 3 sensors of each phase with only one on bus line of converter so as to detect current of every phase. The proposed delta modulation technique has been implemented in a simple digital logic circuit using EPLD(Electrically Programmable Logic Device). This method is verified through simulation and experiment results.

• Proceedings of the Acoustical Society of Korea Conference
• /
• spring
• /
• pp.303-306
• /
• 1999

The paper describes a theoretical study on the speed of the torsional elastic waves propagating in a circular cylinder whose outer radius varies periodically as a harmonic function of the axial coordinate. The approximate solution for the phase speed has been obtained using the perturbation technique for sinusoidal modulation of small amplitude. It is shown that the wave speed in the cylinder with a corrugated outer surface is less than that in a smooth cylinder by the square of the amplitude of the surface perturbation. This theoretical prediction agrees reasonably with an experimental observation reported earlier. It is also shown that the wave speed reduction due to the surface corrugation becomes larger for a thinner cylinder and for a bigger density of corrugation.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.400-402
• /
• 1994

This paper presents a digital implementation of delta modulation Technique for Active Power Filters. Delta modulated scheme is to control the harmonic-compensating current indirectly by adjusting the capacitor voltage to be sinusoidal. The overall control system has two feedback loops. One is the outer propotional feedback for loop regulating the dc current of active filters and the other is the inner feedback loop for maintaining the ac current waveform to be sinusoidal, and have zero power factor angle(i.e. unity power factor). The characteristics of the proposed is investigated by digital simulation using ACSL and experimental results are obtained by TMS370C756 Single-Chip Microprocessor relative to analog delta modulation technique.