• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.7
• /
• pp.615-620
• /
• 2002

In the case of immobilizing of glucose oxidase into polypyrrole (PPy) using electrosynthesis, the glucose oxidise (GOx) forms a coordinate bond with the polymers backbone. However, because of intrinsic insulation and net-chain of the enzyme, the charge transfer and mass transport are obstructed during the film growth. Therefore, the film growth is dull. We synthesized enzyme electrodes by electropolymerization added some organic solvent, such as ethanol and tetrahydrofuran (THF). The formative seeds of film growth was delayed by adding ethanol. The delay was induced by radical transfer between ethanol and pyrrole monomer. The radical transfer reactions shared the contribution of dopants between electrolyte anion and GOx polyanion. This led to increase amount of immobilized the enzyme in PPy. For the UV absorption spectra of synthetic solution before synthesis and after, in the case of ethanol added, the optical density was slightly decreased for the GOx peaks. It suggests amount of GOx in the solution was decreased and amount of GOx in the film was increased.

• Journal of the Korean Electrochemical Society
• /
• v.19 no.2
• /
• pp.45-49
• /
• 2016

In order to mitigate oxidative degradation of polymer membrane during fuel cell operation, an organic radical quencher was introduced. Rutin was selected as a radical quencher and mixed with sulfonated poly(arylene ether sulfone) to prepare composite membrane. Physicochemical properties of the composite membranes such as water uptake and proton conductivity were characterized. Hydrogen peroxide exposure experiment, which can mimic accelerated oxidative stability test during fuel cell operation, was adopted to evaluate the oxidative stability of the membranes. The composite membranes containing Rutin showed similar proton conductivity and enhanced oxidative stability compared to pristine ones.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.489-490
• /
• 2006

Branched sulfonated poly(ether sulfone-ketone) copolymer was prepared with bisphenol A, 4,4-difluorobenzophenone, sulfonated chlorophenyl sulfone (40mole% of bisphenol A) and THPE (1,1,1-tris-p-hydroxyphenylethane). THPE was used 0.4 mol% of bisphenol A to synthesize branched copolymers. Organic-inorganic nano composite membranes were prepared with copolymer and a series of $SiO_2$ nanoparticles (20 nm, 4, 7 and 10 wt%). The composite membranes were cast from dimethylsulfoxide solutions. The films were converted from the salt to acid forms with dilute hydrochloric acid. The membranes were studied by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Sorption experiments were conducted to observe the interaction of sulfonated polymers with water and methanol. Branched copolymer and nano composite membranes exhibit proton conductivities from $1.12{\times}10^{-3}$ to $6.04{\times}10^{-3}\;S/cm^2$, water uptake from 52.9 to 62.4%, IEC from 0.81 to 1.21 meq/g and methanol diffusion coefficients from $1.2{\times}10^{-7}$ to $1.5{\times}10^{-7}\;cm^2/S$.

• Environmental Sciences Bulletin of The Korean Environmental Sciences Society
• /
• v.4 no.3
• /
• pp.173-183
• /
• 2000

This study measured the zeta potential of both latex colloidal particles with carboxylate surface groups and glass beads (collectors) with silanol surface group employing various solution with different chemical characteristics. The results have been compared with the surface chemistry theory. The zeta potential of the particle and collector increased with increasing pH up to 5.0 regardless of the solution chemistry. For a monovalent electrolyte solution(sodium chloride solution) the zeta potential steadily increased until the pH reached 9.5. In contrast, little change in zeta potential was made between 5.0 and 9.5 for a divalent electrolyte solution (sodium chloride solution) the zeta potential steadily increased until the pH reached 9.5. In contrast, little change in zeta potential was made between 5.0 and 9.5 for a divalent electrolyte solution (calcium chloride solution). In other words, the more the pH decreases, the larger the effect of neutral salts, such as NaCl and CaCl$_2$, have on the ζ-potential values. In this study, the PZPC(point of zero proton condition) of the particle and collector occurred below a pH of 3.1, H(sup)+ and OH(sup)- acted as a PDI (potential determining ion), and Na(sup)+ acted as an IDI(indifferent ion). The magnitude of the negative ζ-potential values of the particle and collector monotonically increased as the concentrations of Na(sup)+ or Ca(sup)2+([Na(sup)+] or [Ca(sup)2+]) decreased (the values of pNa or pCa increased). In the case of latex particles, the ζ-potential should aproach zero (isoelectric point; IEP) asymptotically as the pNa approaches zero, while in the case of calcium chloride electrolyte, ζ-potential reversal may be expected to occur around 3.16$\times$10(sup)-2MCaCl$_2$(pCa=1.5). pH, valance and ionic strength can be used in various ways to improve the water treatment efficiency by modifying the charge characteristics of the particle and collector. Predictive capability is far less certain when EDL(electrical double layer) repulsive forces exist between the particle and collector.

• Journal of the Korean Electrochemical Society
• /
• v.5 no.2
• /
• pp.47-51
• /
• 2002

Polyurethane was used as matrix for polymer electrolytes with liquid electrolyte consist of organic solvent as ethylene carbonate(EC), propylene carbonate(PC), and tetraethylene glycol dimethylether(TG) and 1M $LiCF_3SO_3$, which has high mechanical strength and porosity. Electrochemical properties fur polyurethane electrolytes with various liquid electrolytes were evaluated. The amount of immersed liquid electrolyte for TG with 1M $LiCF_3SO_3$ was increased to about $750\%$ by weight, and initial discharge capacity and cycle performance was better than others. Ionic conductivity for TG/EC(v/v,1:1) and PC/EC(v/v, 1:1) with 1M $LiCF_3SO_3$ was about $3.15\times10^{-3} S/cm, \;3.18\times10^{-3}S/cm$

• Applied Chemistry for Engineering
• /
• v.4 no.2
• /
• pp.273-283
• /
• 1993

Addition of various acids or organic compounds to the electrolyte solution during the electrodeposition of $PbO_2$ on titanium madras substrate strongly affected performance of the deposited $PbO_2$ layer. Results of X-ray diffractometry ascertained that ${\beta}-PbO_2$ was deposited in acidic electrolyte. Among additives used in this experiment, $PbO_2$ with a high oxygen overvoltage was electrodeposited when sodium lauryl sulfate was added, and $PbO_2$ with a lower chlorine overvoltage was electrodeposited when polyethylene glycol was added to the electrolyte solution. The oxygen and chlorine overvoltage of $PbO_2$ was strongly dependent on the stirring provided during the electrodeposition experiment. It was observed by the SEM results that the $PbO_2$ grains deposited when stirring was not provided during the electrodeposition have larger than $PbO_2$ grains deposited by stirring. In the $PbO_2$ deposition under acidic electrolyte, the oxygen overvoltage increased with larger $PbO_2$ grains and the chlorine overvoltage decreased with smaller $PbO_2$ grains. The optimal current efficiency of $PbO_2$ in the presence of perchloric acid was observed at $Pb(NO_3)_2$ 560g/l, $65{\sim}70^{\circ}C$, and pH>1.

• Membrane Journal
• /
• v.33 no.6
• /
• pp.325-343
• /
• 2023

Direct methanol fuel cells (DMFCs) have been attracting attention as energy conversion devices that can directly supply methanol liquid fuel without a fuel reforming process. The commercial polymer electrolyte membranes (PEMs) currently applied to DMFC are perfluorosulfonic acid ionomer-based PEMs, which exhibit high proton conductivity and physicochemical stability during the operation. However, problems such as high methanol permeability and environmental pollutants generated during decomposition require the development of PEMs for DMFCs using novel ionomers. Recently, studies have been reported to develop PEMs using hydrocarbon-based ionomers that exhibit low fuel permeability and high physicochemical stability. This review introduces the following studies on hydrocarbon-based PEMs for DMFC applications: 1) synthesis of grafting copolymers that exhibit distinct hydrophilic/hydrophobic phase-separated structure to improve both proton conductivity and methanol selectivity, 2) introduction of cross-linked structure during PEM fabrication to reduce the methanol permeability and improve dimensional stability, and 3) incorporation of organic/inorganic composites or reinforcing substrates to develop reinforced composite membranes showing improved PEM performances and durability.

• Polymer(Korea)
• /
• v.34 no.5
• /
• pp.405-409
• /
• 2010

New sol-gel precursors having the ability to protect iron against corrosion were synthesized and used to prepare organic-inorganic hybrid coatings based on epoxy. Bisphenol A epoxy was modified with 3-isocyanatopropyltriethoxysilane to improve the compatibility, and water and HCl were used as catalysts for sol-gel process. Various coating formulations were prepared depending on the type of sol-gel precursors and the amount of each ingredient, and cast on iron substrates by dip-coating and thermally cured. Corrosion protection properties of coated iron were studied by a salt spray test and electrochemical impedance spectroscopy under 0.1 M NaCl electrolyte. Hybrid coatings containing anticorrosive functional group exhibited excellent corrosion protection on iron, compared to that of typical hybrid coatings. From electrochemical impedance spectroscopy, the hybrid coatings containing anticorrosive functional group could maintaine the initial impedance after 500 h, while the impedance of hybrid coatings without them started to decrease after 24 h.

• Korean Chemical Engineering Research
• /
• v.52 no.1
• /
• pp.26-39
• /
• 2014

Cu interconnection in electronic devices is fabricated via damascene process including Cu electrodeposition. In this review, Cu electrodeposition and superfilling for fabricating Cu interconnection are introduced. Superfilling results from the influences of organic additives in the electrolyte for Cu electrodeposition, and this is enabled by the local enhancement of Cu electrodeposition at the bottom of filling feature formed on the wafer through manipulating the surface coverage of organic additives. The dimension of metal interconnection has been constantly reduced to increase the integrity of electronic devices, and the width of interconnection reaches the range of few tens of nanometer. This size reduction raises the issues, which are the deterioration of electrical property and the reliability of Cu interconnection, and the difficulty of Cu superfilling. The various researches on the development of organic additives for the modification of Cu microstructure, the application of pulse and pulse-reverse electrodeposition, Cu-based alloy superfilling for improvement of reliability, and the enhancement of superfilling phenomenon to overcome the current problems are addressed in this review.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.85.2-85.2
• /
• 2010

There is widespread effort to develop polymer membranes in place of Nafion for high temperature polymer electrolyte membrane fuel cell(PEMFC). In our study, SiO2 membranes are arranged by electrospinning method. For impregnation solution, the modified sulfonated poly(ether ether ketone)(SPEEK) polymer is prepared from sulfonation, sulfochlorination, partial reduction and lithiation reaction. The modified polymer is cross-linked with 1,4-diiodobetane in NMP solvent and then blended with Heteropoly acid(HPA). The characterization of membranes is confimed by FT-IR, Thermogravimetry(TGA), water uptake test and single cell performance test for PEMFC, etc. The composite membrane shows satisfactory thermal and mechanical properties. Beside, The membrane exhibits good ion exchange capacity and high proton conductivity. As a result, The composite membrane is promising as an alternative membrane in high temperature PEMFC.