• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.533-538
• /
• 2001

This paper describes a combinational method to compute the global and local solutions of optimization problems. The present hybrid algorithm uses both a genetic algorithm and a local concentrate search algorithm (e. g simplex method). The hybrid algorithm is not only faster than the standard genetic algorithm but also supplies a more accurate solution. In addition, this algorithm can find the global and local optimum solutions. The present algorithm can be supplied to minimize the resonance response (Q factor) and to yield the critical speeds as far from the operating speed as possible. These factors play very important roles in designing a rotor-bearing system under the dynamic behavior constraint. In the present work, the shaft diameter, the bearing length, and clearance are used as the design variables.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.5
• /
• pp.579-588
• /
• 2003

Optimum fin effectiveness of geometrically and thermally asymmetric trapezoidal fins is represented as a function of the ratio of the fin bottom to top Biot numbers, the ratio of the fin tip to top Biot numbers and fin shape factor. Optimum fin effectiveness is taken as 98% of the maximum fin effectiveness by comparing the increasing rate of fin effectiveness with that of dimensionless fin length. For this analysis, two dimensional separation of variables method is used. Also, the value of the slope of upper surface of the fin and fin efficiency corresponding to optimum effectiveness are presented.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.21 no.4
• /
• pp.29-39
• /
• 1984

In this paper, the membrane and buckling analysis of beams with various shaped brackets is performed by using the finite element method. From the viewpoint of minimum structural weight, a optimum design method to determine the optimal shapes and scantling of brackets under design load is proposed by investigating the effects of beam depth, bracket length and aspect ratio on the structural weight. Also optimal design data and charts for the brackets to support transverse girders or web frames of actual ships are provided. By the present design method, it is possible to perform optimum design of brackets used in actual ships, which could result in considerable reduction of structural weight or cost, increase of dead weight and service speed of ships.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.99-100
• /
• 2006

One of the fundamental problems in sensor networks is the deployment of sensor nodes. The Fuzzy C-Means(FCM) clustering algorithm is proposed to determine the optimum location and minimum number of sensor nodes for the specific application space. We performed a simulation using two dimensional L shape model. The actual length of the L shape model is about 100m each. We found the minimum number of 15 nodes are sufficient for the complete coverage of modeled area. We also found the optimum location of each nodes. The real deploy experiment using 15 sensor nodes shows the 95.7%. error free communication rate.

• Journal of information and communication convergence engineering
• /
• v.13 no.2
• /
• pp.69-73
• /
• 2015

We focus on a sounding signal design for single-input single-output orthogonal frequency division multiplexing (SISO-OFDM) systems. We show that the frequency spectrum of an optimum sounding signal has a constant magnitude across the frequency band for the cases with or without Doppler effects. Simulation results show that the designed optimum sounding signal outperforms random sounding signals and that the performance of a maximal-length shift register sequence is indistinguishable from that of the optimum sounding signal.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1713-1715
• /
• 2003

This paper describes an LED module for a desk lamp using 1[W] high flux while LEDs. The optimum length of the module is obtained from the lighting simulation of the target area of $500{\times}500[mm]$ on the desk, which in turn determines an optimum separation between LEDs. The main issue is to find the optimum separation which gives good illuminance uniformity and high coefficient of utilization at at various reflector structures. Two module configuations of linear and ring types are compared. As a result, good illuminance uniformity is obtained in the case of the ring module. The mofied twin type, however, gives better performance than the ring module, and shows the most performance at an separation angle of around $30^{\circ}$.

• International Journal of Industrial Entomology and Biomaterials
• /
• v.14 no.1
• /
• pp.23-32
• /
• 2007

The nature of genetic variation and diversity among the 65 multivoltine silkworm genotypes was evaluated for 16 post cocoon characters. The components of genetic variation revealed higher PCV (60.487%) and GCV (44.56%) for evenness (variation 1) followed by cohesion (PCV=55.38%, GCV=40.36%) and non-broken filament length (PCV=32.05%, GCV=31.28%). The higher heritability ($h^2$ in broad sense) was observed for boil-off loss (95.6%) followed by non-broken filament length (95.22%). The both genotypic and phenotypic correlation indicated significant positive correlation of filament length with non-broken filament length, silk recovery, raw silk, neatness, and low neatness; and negative correlation with denier, renditta and silk waste. The principal component analysis (PCA) revealed 75.381 % of total variance from the five principal components extracted. On the basis of Mahalonobis' $D^2$ values (Ward's minimum variance), the sixty-five multivoltine silkworm genotypes were classified in to 9 clusters with substantial inter and intra cluster distances. Number of genotypes included in different clusters varied from 3 to 17. The results indicated that the optimum distance obtained in cluster VII (15.059) along with higher cluster mean values especially for filament length, non broken filament length, renditta, silk recovery, silk waste, and raw silk emphasized the utilization of these genotypes in the conventional silkworm breeding programme for improvement of multivoltine silk fibre quality. The possibility of exploiting genetic variation in post cocoon traits for efficient breeding programme is discussed.

• Fisheries and Aquatic Sciences
• /
• v.12 no.4
• /
• pp.342-349
• /
• 2009

The purpose of the current study was to optimize shrimp-pot design to allow greater control over the size of captured individuals for the purposes of shrimp resource management. Tank experiments were conducted to determine the optimal slope length and slope angle by analyzing the sizes of shrimp that entered 25 model pots with combinations of five different slope lengths and five different angles. Shrimp size was measured using carapace length. The results showed that as the slope angle of the pot increased, the size of individuals that entered the pot increased. Furthermore, as the slope length increased, each of the five different slope angles of the pot increased, and the size of individuals entering also increased. The data indicated that the optimum pot design for reducing the capture of immature individuals had a $75^{\circ}$ slope angle and a 35.4 cm slope length.

• Proceedings of the SAREK Conference
• /
• 2006.11a
• /
• pp.53-53
• /
• 2006

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.6
• /
• pp.48-56
• /
• 2012

Radiation characteristics of inductive loaded patch antennas (ILPAs) and conventional patch antennas using a half wavelength resonance mode for substrates with various dielectric constants are investigated. ILPAs have the good radiation characteristics such as high broadside gain and suppressed radiation along the horizontal plane compared to those of conventional patch antennas. We show that ILPAs with the appropriate patch length and via radius have the optimum radiation characteristics such as the highest broadside gain and the most suppressed horizontal radiation.