• Advances in concrete construction
• /
• v.6 no.1
• /
• pp.29-45
• /
• 2018

This paper investigates the effect of inclusion of glass fibers on mechanical and fracture properties of binary blend geopolymer concrete produced by using fly ash and ground granulated blast furnace slag. To study the effect of glass fibers, the mix design parameters like binder content, alkaline solution/binder ratio, sodium hydroxide concentration and aggregate grading were kept constant. Four different volume fractions (0.1%, 0.2%, 0.3% and 0.4%) and two different lengths (6 mm, 13 mm) of glass fibers were considered in the present study. Three different notch-depth ratios (0.1, 0.2, and 0.3) were considered for determining the fracture properties. The test results indicated that the addition of glass fibers improved the flexural strength, split tensile strength, fracture energy, critical stress intensity factor and critical crack mouth opening displacement of geopolymer concrete. 13 mm fibers are found to be more effective than 6 mm fibers and the optimum dosage of glass fibers was found to be 0.3% (by volume of concrete). The study shows the enormous potential of glass fiber reinforced geopolymer concrete in structural applications.

• Advances in concrete construction
• /
• v.8 no.4
• /
• pp.305-309
• /
• 2019

Pervious concrete pavements are the need of the day to avoid urban flooding and to facilitate ground water recharge. However, the strength of pervious or porous concrete is considerably less compared to conventional concrete. In this experimental investigation, an effort is made to improve the strength of pervious concrete by adopting fibres and a small amount of fine aggregate. A porous concrete with cement to aggregate ratio of 1:5 and a water-powder ratio of 0.4 is adopted. 30% of the cement is replaced by cementitious material ground granulated blast furnace slag (GGBS) for better strength and workability. Recron fibres at a dosage of 0.5, 1.0 and 1.5% by weight of cement were included to improve the impact strength. Since concrete pavements are subjected to impact loads, the impact strength was also calculated by "Drop ball method" in addition to compressive strength. The effect of fine aggregate and recron fibres on workability, porosity, compressive and impact strength was studied. The investigations have shown that 20% inclusion of fine aggregate and 1.5% recron fibres by weight of cement give better strength with an acceptable range of porosity.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.40 no.4
• /
• pp.27-33
• /
• 2008

Polyethylene terephtahalate has been used in several areas such as fiber, film, bottle, and disposable products. Production of PET has been rapidly increasing these days. Since PET is a semi-permanent material, it has a non-biodegradable character in itself. Wasted PET products can cause serious environmental problems. Many countries around the world impose environmental legal restrictions over their abandonments. Many researches on the enviromental influence factors and treatment techniques of the wasted PET have been carried out. The main objective of this study is to develop a new sizing agent using recycling PET and improve its internal sizing effect. Dried powder of PET was used to make the modified PET. After extracting water-dispersible PET by subcritical hydrolysis, polyester resins have been extracted and triphenyl phosphate(TPP) has been added to obtain optimal internal sizing agent. It was found that the optimum dosage of TPP was 2% (per PET weight) and the hydrolysis temperature was independent on making the modified PET.

• Journal of Korean Society on Water Environment
• /
• v.28 no.5
• /
• pp.639-645
• /
• 2012

The purpose of this study is to identify the possibility of the CMP wastewater treatment from semiconductor fabrication under operating tubular membrane with coagulants. To find suitable coagulants treating CMP wastewater, we conducted Jar-test. After Jar-test experiments suitable coagulants are PAC(17%), $Ca(OH)_2$ and optimum coagulant dosage is PAC(17%) 10mg/L, $Ca(OH)_2$ 110 ~ 120mg/L. Based on these results, the tubular membrane was applied to CMP wastewater, the turbidity removal efficiency is $Ca(OH)_2$ > PAC(17%) > Nothing. The fast cross-flow velocity and backwash process what are operating characteristics of tubular membrane can be stable CMP wastewater treatment. But when the coagulant and tubular membrane are used at the same time, the withdraw and treatment of the CMP wastewater are possibile. However further treatment process needs if treated water will be used for semiconductor fabrications.

• Environmental Engineering Research
• /
• v.21 no.1
• /
• pp.29-35
• /
• 2016

This study evaluated the fertilizing value of struvite deposit recovered from swine wastewater in cultivating lettuce. Struvite deposit was compared to complex fertilizer, organic fertilizer and compost to evaluate the fertilizing effect of struvite deposit. Laboratory pot test showed that the struvite deposit better enhanced lettuce growth in comparison to commercial fertilizers. It was revealed that the growth rate of lettuce was simultaneously controlled by phosphorus (P) and magnesium (Mg). Moreover, nutrients such as nitrogen (N), P, K, calcium (Ca) and magnesium (Mg) were abundantly observed in the vegetable tissue of struvite pot. Meanwhile, struvite application led to the lower accumulation of mercury (Hg), lead (Pb), chromium ($Cr^{6+}$) and nickel (Ni). In addition, no detection of cadmium (Cd), arsenic (As) and nickel (Ni) in the lettuce tissue was observed in struvite application pots. The experimental results proved that the optimum struvite dosage for lettuce cultivation was 0.5 g struvite/kg soil. The column experiments clearly showed that ammonia nitrogen was more slowly released from struvite deposit than from complex fertilizer. Consequently, it was concluded that the struvite deposits recovered from swine wastewater were effective as a multi-nutrient fertilizer for lettuce cultivation.

• Journal of Environmental Science International
• /
• v.13 no.10
• /
• pp.921-928
• /
• 2004

The photocatalytic decolorization of Rhodamine B (RhB) was studied using immobilized $TiO_2$ and fluidized bed reactor. Immobilized $TiO_2$(length: 1$\~$2 mm, width: 1$\~$3 mm, thickness: 0.5$\~$2 mm) onto silicone sealant was employed as the photocatalyst and a 30 W germicidal lamp was used as the light source and the reactor volume was 4.8 L. The effects of parameters such as the amounts of photocatalyst, initial concentration, initial pH, superficial velocity, $H_2O_2$ and anion additives. ($NO_3^{-},\;SO_4^{2-},\;Cl^{-},\;CO_3^{2-}$) The results showed that the optimum dosage of the immobilized $TiO_2$ were 87.0 g/L. Initial removal rate of RhB of the immobilized $TiO_2$ was 1.5 times higher than that of the powder $TiO_2$ because of the adsorption onto the surface of immobilized $TiO_2$ In the conditions of acidic pH, initial reaction rate was increased slowly and reaction time was shorted. The effect of anion type on the reaction rate was not much.

• KSBB Journal
• /
• v.11 no.6
• /
• pp.726-732
• /
• 1996

Selective adsorption of plant metabolites from a polar dilute solution onto a polycarboxyl ester sorbent (XAD-7) was investigated. Experimental results demonstrated that neutral resins could selectively concentrate specific flavonoids from dilute aqueous mixtures. Adsorption was dependent on the pH of medium, dosage of the resins and medium composition. Especially the medium composition was a key factor for the selective adsorption and it was found that the selective adsorption was dependent on specific sorbent-sorbate-medium characteristics. Under the optimum condition, selectivity increased up to 85% and the yield of recovery was approached to 98%. It was also found that XAD-7 adsorbed flavonoids in the order of hydrophobicity.

• KSBB Journal
• /
• v.9 no.2
• /
• pp.122-126
• /
• 1994

A new method for the production of isomalto-oligosaccharides from maltose was investigated using intact cells of Aureobasidium pullulaans which had been known to produce fructo-oligosaccharides. The cells showed transglucosylation activity producing isomalto-oligosaccharides at high concentrations of maltose, while they showed a hydrolytic activity at low concentrations of substrate when cultivated at $25^{\circ}C$. The optimum reaction conditions for the isomalto-oligosaccharide production were as follows: substrate concentration, 500g/l maltose; pH, 4.5; temperature, $65^{\circ}C$; cell dosage, 10 unit per gram substrate. Under optimized conditions, the maximum yield of isomalto-oligosaccharides achieved was around 48% (w/w). At the early period of reaction, panose was selectively produced from maltose, and thereafter isomaltotriose was synthesized by utilizing panose as a substrate when maltose consumption was discontinued.

• Journal of Environmental Health Sciences
• /
• v.27 no.2
• /
• pp.60-66
• /
• 2001

Natural organic matters(NOMs) are found everywhere such as soil, surface and ground waters and consist of both humic and nonhumic components, and their heterogeneith makes each source unique. This study was carried to evaluate the removal characteristics of NOMs by mixing coagulants and the variation of apparent molecular weight distribution(AMWD) in coagulation process. Ratio of optimum coagulants dosage for removal of DOC and turbidity by mixing coagulants was 1.83 mM F $e^{3+}$/mM $Al^{3+}$. DOC removal increased at lower pH. The pH6 control focused on the removal of organic matters could reduce the amount of coagulant consumption by 2 to 3 times based on the pH8.5 of natural water. The dissolved organic matters in the natural water from the mid-stream of Han River were composed of the low molecular weight(LMW,<1 K) of 59.7%, and the medium and high molecular weight(M.HMW, 1~30 K) of 40.3%, respectively. At pH6, the DOC removal efficiencies of LMW(<1 K) and M.HMW(1~30 K) in coagulation process were 27~35%, 62~72%, respectively. The fraction smaller than 1 K was not eliminated to a noticeable degree, while the fraction of 1~30 K was relatively well removed. In conclustion, mixing coagulants were fairly effective in the removal of natural organic matter.r.

• Carbon letters
• /
• v.8 no.3
• /
• pp.199-206
• /
• 2007

The activated carbon produced from rubber wood sawdust by chemical activation using phosphoric acid have been utilized as an adsorbent for the removal of Cu(II) from aqueous solution in the concentration range 5-40 mg/l. Adsorption experiments were carried out in a batch process and various experimental parameters such as effect of contact time, initial copper ion concentration, carbon dosage, and pH on percentage removal have been studied. Adsorption results obtained for activated carbon from rubber wood sawdust were compared with the results of commercial activated carbon (CAC). The adsorption on activated carbon samples increased with contact time and attained maximum value at 3 h for CAC and 4 h for PAC. The adsorption results show that the copper uptake increased with increasing pH, the optimum efficiency being attained at pH 6. The precipitation of copper hydroxide occurred when pH of the adsorbate solution was greater than 6. The equilibrium data were fitted using Langmuir and Freundlich adsorption isotherm equation. The kinetics of sorption of the copper ion has been analyzed by two kinetic models, namely, the pseudo first order and pseudo second order kinetic model. The adsorption constants and rate constants for the models have been determined. The process follows pseudo second order kinetics and the results indicated that the Langmuir model gave a better fit to the experimental data than the Freundlich model. It was concluded that activated carbon produced using phosphoric acid has higher adsorption capacity when compared to CAC.