• The KSFM Journal of Fluid Machinery
• /
• v.9 no.6 s.39
• /
• pp.22-28
• /
• 2006

Operation of a microturbine was simulated on the basis of component characteristic parameters obtained from performance test. Characteristic parameters, such as compressor and turbine efficiencies, recuperator effectiveness as well as turbine inlet temperature, were obtained for a wide operation range. Component characteristics including performance maps and characteristic curves were generated using measured data. Based on the component characteristics, a simulation program was constructed and operation of the microturbine was simulated, and the simulated results were compared with the measured data to verify the program. Also, influence of variation in the power control scheme on the operating characteristic and performance of the engine was simulated. The simulation program can be used for predicting operation of both healthy and degraded engine conditions.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.2286-2291
• /
• 2011

Technology on the rolling stock is very composition and system engineering. We have to consider to many parameters on the rolling stock design. High speed train is interface between rolling stock and infra system of rail, signal, communication etc. For many years testing operation has experienced substantial growth based on various advanced new technology. Recently some problems was clearly stated on effective management, practical use and testing operation of the the rolling stock on the technology change. This paper presents some results of the study on necessary requirements of the operation testing for rolling stock technology change. We propose a general plan to suggest the operation testing and the parameters of the rolling stock on the technology change in the text.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.368-371
• /
• 2008

The optimal operation condition of gasifier is one of the most important parameters to increase efficiency and reliability in IGCC plant. Also the prediction of the syngas composition and quantity must be predicted to carry out process design of the gasification plant. However, the gasifier process licensor are protective with information on process design and optimal gasifier design conditions. So, the most of process studies in the engineering company for gasification plant have carried out to look for key parameters and optimal design conditions using several prediction methods. In this paper, we present the estimated preliminary optimal operation condition of the 300MW Demonstration Entrain Flow Gasifier using Aspen Plus. The gasifier operation temperature considering slag flow was predicted by FactSage software and Annen Model.

• Proceedings of the KIEE Conference
• /
• 2004.10a
• /
• pp.43-45
• /
• 2004

This paper represents the improvement of floating point operation for AC servo motor controller based on fixed point operation DSP. TMS320F2812 has fixed point operation processing structure. The controller parameters are modified to the digitized data by scaling the original parameters. TMS320F 2812 is a 32-bit processor, and it could have enough accuracy to get the digitized data this procedure is implemented and the experiments controling a AC servo system.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2002.10a
• /
• pp.137-140
• /
• 2002

The monitoring system for integrated management of on-site wastewater treatment plants(biofilter) was designed and its operation program was developed. In design process, the research on monitoring parameters which will be able to represent condition and operation of the pilot plants was accomplished, and these parameters came to reveal with ORP(Oxidation-Reduction Potential), water level, pump and power on/off. Proposed monitoring system is composed with measurement, control, communication and display device, and PCB(Prototype Circuit Boards) and microcontroller (PIC16F877) technique are applied to its design of control device for performing specific function. also, The operation program of PC setup is developed in order to provide a convenience to the manager.

• Journal of Electrical Engineering and Technology
• /
• v.3 no.1
• /
• pp.29-35
• /
• 2008

With long time setting, zone 3 impedance relays are considered insensitive to power swings, and their operation condition during power swings is seldom analyzed. Instead of ti me-consuming simulation to the swing loci, their operation condition is directly quantified by polynominal functions in this paper to find the critical swing angle and frequency for relay operation under different relay settings and system parameters. It is found: (1) the swing loci are more densely populated inside than outside of the protection region, which corresponds to long residence time and possible relay operations; (2) the relays may be sensitive to load encroac hments and stable power swings with different relay settings and system parameters; (3) the critical swing frequency may be in the range of low-frequency power swings.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1196-1198
• /
• 2004

This paper represents the improvement of floating point operation for AC servo motor controller based on fixed point operation DSP. TMS320F2812 has fixed point operation processing structure. The controller parameters are modified to the digitized data by scaling the original parameters. TMS320F 2812 is a 32-bit processor, and it could have enough accuracy to got the digitized data this procedure is implemented and the experiments controling a AC servo system.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.11
• /
• pp.5128-5134
• /
• 2011

This paper investigates the dq current trajectory for maximum torque per ampere(MTPA) operation of an interior PM synchronous motor for HEV(Hybrid Electric Vehicle). Based on the dq current trajectory for the MTPA operation derived from the motor parameters, the change of the MTPA operating point for the variation of the motor parameters including the magnet flux and the dq inductances is considered. The dq current trajectory for MTPA operation is verified through the experiment.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.863-869
• /
• 2007

An improved method based on a normal frequency response function (FRF) is proposed to identify structural parameters such as mass, stiffness and damping matrices directly from the FRFs of a linear mechanical system. The method for estimating structural parameters directly from the measured FRFs of a structure is presented. This paper demonstrates that the characteristic matrices are extracted more accurately by using a weighted equation and eliminating the matrix inverse operation. The method is verified for a four degree-of-freedom lumped parameter system and an eight degree-of-freedom finite element beam. Experimental verification is also performed for a free-free steel beam whose size and physical properties are the same as those of the finite element beam. The results show that the structural parameters, especially the damping matrix, can be estimated more accurately by the proposed method.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.3
• /
• pp.97-103
• /
• 2001

This paper has focused on the Optimization of the cutting parameters for urning operation based on the Taguchi method. Four cutting parameters. nemely, cutting speed, feed depth of cut and nose radius are optimized with consideration of the surface roughness. The design and analysis of experiments are conducted to study the performance characteristic. The effects of these parameters on the surface roughness have been investigated using signal-to-noise(S/N) ratio and analy-sis of variance(ANOVA). The experiments have been performed using coated tungsten carbide inserts without any cutting fluid. Experimental results illustrate the effectiveness of this approach.