• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.16 no.1
• /
• pp.46-56
• /
• 1991

In this paper, 16word X 8bit Content Addressable and Reentrant Memory(CARM) is described. This device has 4 operation modes(read, write, match, reentrant). The read and write operation of CARM is like that of static RAM, CARM has the reentrant mode operation where the on chip garbage collection is accomplished conditionally. Thus function can be used for high speed matching unit of dynamic data flow computer. And CARM also can encode matching address sequentially according to therir priority. CARM consists of 8 blocks(CAM cell, Sequential Address Encoder(S.A.E). Reentrant operation. Read/Write control circuit, Data/Mask Register, Sense Amplifier, Encoder. Decoder). Designed DARM can be used in data flow computer, pattern, inspection, table look-up, image processing. The simulation is performed using the QUICKSIM logic simulator and Pspice circuit simulator. Having hierarchical structure, the layout was done using the 3{\;}\mu\textrm{m} n well CMOS technology of the ETRI design rule.

• Tribology and Lubricants
• /
• v.33 no.1
• /
• pp.9-14
• /
• 2017

This paper presents a rotordynamic analysis and the operation of a power turbine applied to a 250 kW super-critical $CO_2$ cycle. The power turbine consists of a turbine wheel and a shaft supported by two fluid film bearings. We use a tilting pad bearing for the power turbine owing to the high speed operation, and employ copper backing pads to improve the thermal management of the bearing. We conduct a rotordynamic analysis based on the design parameters of the power turbine. The dynamic coefficients of the tilting pad bearings were calculated based on the iso-thermal lubrication theory and turbine wheel was modeled as equivalent inertia. The predicted Cambell diagram showed that there are two critical speeds, namely the conical and bending critical speeds under the rated speed. However, the unbalance response prediction showed that vibration levels are controlled within 10 mm for all speed ranges owing to the high damping ratio of the modes. Additionally, the predicted logarithmic decrement indicates that there is no unstable mode. The power turbine uses compressed air at a temperature of $250^{\circ}C$ in its operation, and we monitor the shaft vibration and temperature of the lubricant during the test. In the steady state, we record a temperature rise of $40^{\circ}C$ between the inlet and outlet lubricant and the measured shaft vibration shows good agreement with the prediction.

• Journal of Animal Science and Technology
• /
• v.48 no.2
• /
• pp.315-324
• /
• 2006

This research was conducted to clarify the characteristics of electrochemical decolorization of effluent discharged from a biological animal wastewater treatment process and to finally establish parameters or mode for optimum operation of electrolysis system. Average color unit of wastewater was about 1,200 and DSA(Dimensionally Stable Anode) was used as electrode. Experiments were performed with two different operation conditions or modes, fixed voltage-free current(Run A) and free voltage-fixed current(Run B). Color removal rate was proportional to the electrode area and electrical conductivity, and an equation subject to them at a condition of fixed voltage was derived as follows; Ct=C0ekt, k=[{0.0121×ａ(dm2)× c(mS/cm)}+0.0288], [where, C0: initial color, Ct: color unit after treatment for t, k: reaction coefficient, t: time(min.), ａ: electrode area, c: conductivity]. From the study on the effects of current density on color removal, it was revealed that the removal efficiency of color was function of the current density, showing direct proportion. However, when considered energy consumption rate, maintenance of low current density was an economical way. Based on the obtained results, it was concluded that supplementation of electrolyte is not necessary for the removal of color from the effluent of secondary treatment process and operation with the mode of free voltage-fixed current, rather than operation with fixed voltage-free current mode, would be an efficient way to increase the removal performance and capacity per consumed energy.

• Membrane Journal
• /
• v.14 no.1
• /
• pp.75-84
• /
• 2004

In this study, we present a noble study far membrane transport models using chlorine resistance of polyamide RO membranes. Membrane transport mechanism is investigated by the comparison of membrane permeation performance under the continuous and Intermittent operation modes with mixed feed solution containing NaOCl and NaCl. Analysis of permeation performance indicates that solution-diffusion model and preferential adsorption-capillary flow model are relatively efficient according to operation mode. Under the continuous flow state, mass transfer depends on preferential adsorption-capillary flow model rather than solution-diffusion model. On the other hand, it prefers solution-diffusion model to preferential adsorption-capillary flow model under the stationary state. SEM images of NaOCl treated membrane surfaces strongly support these conclusions. These surface images reveal that NaOCl treated membrane in continuous operation mode exhibits ridge and valley structure in some fraction of the surface area, whereas that in intermittent operation mode shows surface degradation entirely.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.1
• /
• pp.113-119
• /
• 2003

During the mission operation time, it is very important to estimate the spacecraft propellant remaining as accurately as possible. This is because the quantity of propellant is related directly to how long the satellite can be operated ín orbit. There are two different methods for spacecraft propellant gauging; the PVT method and the book-keeping method. This paper describes the characteristics and applications of these methods using the flight operation data of KOMPSAT-1. Additionally, propellant consumption rates in delta-V maneuvering and each attitude control submode are analyzed according to spacecraft operation modes. The earth search submode shows the highest propellant consumption rate.

• Membrane Journal
• /
• v.29 no.4
• /
• pp.216-222
• /
• 2019

In this study, permeation experiments were conducted using naturally circulating spherical beads, backwashable plate membrane and the air supplied from the bottom of the MBR. The activated sludge solution was maintained at 8,000 mg/L of MLSS and compared transmembrane pressure (TMP) with respect to FR (filtration and relaxation), FR/BW (filtration and relaxation/backwashing), SFCO (sinusoidal filtration continuous operation) and SFCO/BW (sinusoidal filtration continuous operation/backwashing). As the backwashing flux decreased from 47 to $14L/m^2{\cdot}hr$, the TMP increased generally, but the TMP of FR system increased significantly comparing with SFCO. In addition, the backwashing method reduced more TMP comparing to the cleaning method using spherical beads, and it was confirmed that the operation method using the spherical beads and the backwashing simultaneously is more effective than each method.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.917-924
• /
• 2019

This paper presents a wideband low noise amplifier (LNA) that is suitable for LTE-Advanced and 5G communication standards employing carrier aggregation (CA). The proposed LNA encompasses a common input stage and a dual output second stage with a buffer at each distinct output. This architecture is targeted to operate in both intra-band (contiguous and non-contiguous) and inter-band CA. In the proposed design, the input and second stages employ a gm enhancement with resistive feedback technique to achieve self-biasing, enhanced gain, wide bandwidth as well as reduced noise figure of the proposed LNA. An up/down power controller controls the single input single out (SISO) and single input multiple outputs (SIMO) modes of operation for inter-band and intra-band operations. The proposed LNA is designed with a 45nm CMOS technology. For SISO mode of operation, the LNA operates from 0.52GHz to 4.29GHz with a maximum power gain of 17.77dB, 2.88dB minimum noise figure and input (output) matching performance better than -10dB. For SIMO mode of operation, the proposed LNA operates from 0.52GHz to 4.44GHz with a maximum voltage gain of 18.30dB, a minimum noise figure of 2.82dB with equally good matching performance. An $IIP_3$ value of -6.7dBm is achieved in both SISO and SIMO operations. with a maximum current of 42mA consumed (LNA+buffer in SIMO operation) from a 1.2V supply.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.2
• /
• pp.285-289
• /
• 2020

The configuration of hierarchical wireless networks is provided to support diverse network environments. In the base station, two system state can be basically considered for the operation management so that the state transition may be occurred between active and sleep modes. Hence, to reduce energy consumption the system operation management of the low power should be considered to the base station system. In this paper we consider the analytical model of Discontinuous Reception (DRX) to investigate the system management. We provide the analysis scheme of base station system by the DRX model, and the low power factor would be investigated for the energy consumption. We also use the finite-state Markov system model that in a system state period the wireless resource request and the operation of service call arrival interval is considered to numerically analyze the performance of energy saving operations of base station.

• The Korean Journal of Pain
• /
• v.35 no.1
• /
• pp.114-123
• /
• 2022

Background: Different views have been proposed on the radiofrequency treatment modes and parameters of radiofrequency thermocoagulation of the spinal dorsal root ganglion for the treatment of postherpetic neuralgia (PHN). It is urgent to identify a more effective therapy for patients with PHN. Methods: Patients who underwent radiofrequency thermocoagulation therapy for PHN were retrospectively reviewed and were divided into a radiofrequency thermocoagulation (CRF) and double neddles radiofrequency thermocoagulation (DCRF). The pain scores (numerical rating scale, NRS) were evaluated at the following time points: before the operation, 1 day, 3 months, 6 months, 1 year, and 2 years after operation. The incidence of complications and the degree of pain relief were evaluated. The in vitro ovalbumin experiment was used to indicate the effects of radiofrequency thermocoagulation. Results: Compared with the preoperative NRS scores, the postoperative NRS scores decreased significantly; the NRS scores of the DCRF group was lower than that of the CRF group at all time points from 6 months to 2 years following the operation. The total effective rate of the DCRF group was significantly higher than that of the CRF group at 2 years following the operation. The incidence of numbness in the DCRF group was higher than that noted in the CRF group. The ovalbumin experiments in vitro indicated that the effects of radiofrequency thermocoagulation were optimal when the distance between the two needles was 5 mm. Conclusions: DCRF with a 5 mm spacing exhibits a longer duration and higher effective rate in the treatment of PHN and is worth promoting.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.26 no.4
• /
• pp.548-555
• /
• 2022

This paper describes the hardware implementation of elliptic curve cryptography (ECC) used as a core operation in elliptic curve digital signature algorithm (ECDSA). The ECC processor supports eight operation modes (four point operations, four modular operations) on the NIST P-521 curve. In order to minimize computation complexity required for point scalar multiplication (PSM), the radix-4 Booth encoding scheme and modified Jacobian coordinate system were adopted, which was based on the complexity analysis for five PSM algorithms and four different coordinate systems. Modular multiplication was implemented using a modified 3-Way Toom-Cook multiplication and a modified fast reduction algorithm. The ECC processor was implemented on xczu7ev FPGA device to verify hardware operation. Hardware resources of 101,921 LUTs, 18,357 flip-flops and 101 DSP blocks were used, and it was evaluated that about 370 PSM operations per second were achieved at a maximum operation clock frequency of 45 MHz.