• 소음진동
• /
• 제6권6호
• /
• pp.835-842
• /
• 1996

To identify the locations and strengths of acoustic sources, one may use a microphone line array. Apparent advantage of the source identification method utilizing a line array is that it requires less measurement points than intensity method and holography. This method is based on the information of magnitude and phase difference between pressure signals at each microphone. Since those differences are dependent on the source model, we have to assume them such as plane, monopole, etc. In this paper the conventional source identification methods such as beamforming method and MUSIC method are briefly reviewed by modeling a source as plane and spherical wave, then a modified method is introduced. This can be applied to sound field which may by either coherent or incoherent. Typical simulations and experiment are performed to confirm this identification method.

• 드라이브 ㆍ 컨트롤
• /
• 제14권3호
• /
• pp.32-39
• /
• 2017

In this study, a mathematical model of the pneumatic part in a gas blow-down system is proposed. The mathematical model consists of four major parts: pressure vessel, reservoir, pressure regulator and pipe-line. To ensure accuracy in long-time simulations, heat transfer between gas and pressure vessel is considered. The model is validated by comparing simulation results with experimental data. Experiments are conducted on the ground, where free convection can be assumed. Simulation results indicate the proposed model can accurately describe behavior of a gas blow-down system. Therefore, it may be used for design and analysis of similar systems with a slight modification.

• 한국음향학회지
• /
• 제32권4호
• /
• pp.361-368
• /
• 2013

진동하는 현의 성질을 나타내는 방법으로 반대 방향으로 진행하는 파가 현과 전송선로에 존재한다는 사실에 기초하여 현은 전송선로에 비유되어왔다. 이러한 비유에서 현의 강역(rigid end)과 변위는 각각 전송선로의 개방회로와 전류로 나타내어졌다. 그러나, 본 연구에서 강역과 변위는 각각 단락회로와 전압에 해당됨이 전송선로의 이론으로부터 밝혀졌고 이를 회로시뮬레이션으로 확인하였다. 이러한 발견에 기초하여 전송선로, 구분적 선형 전류원, 스위치들로 구성된 전송선로 기반 탄현 모델을 제안하였다. 임의로 선택된 지점에서의 전압과 전송선로 끝 극소 부분 양단에서 계산된 전압이 현의 성질을 지배하는 파동방정식의 차분형식(difference form)으로 구한 해당 지점에서 변위와 강역에서의 힘과 일치함을 보임으로서 제안한 모델이 정당함을 증명하였다. 또한, 제안된 모델의 현악기 및 관악기 모델링의 적용성을 제시하였다.

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2008년도 International Symposium on Remote Sensing
• /
• pp.297-300
• /
• 2008

High-resolution mesoscale meteorological modeling requires more accurate and higher resolution digital elevation model (DEM) data. Shuttle Radar Topographic Mission (SRTM) has created 90 m DEM for entire globe and that is freely available for meteorological modeling and environmental applications. In this research, the effects of the topographic interpolation methods on high-resolution wind field simulation in the coastal regions were quantitatively analyzed using Weather Research and Forecasting (WRF) model with SRTM data. Sensitivity experiments with three different interpolation schemes (four-point bilinear, sixteen-point overlapping parabolic and nearest neighbor interpolation methods) were preformed using SRTM. In WRF modeling with sixteen-point overlapping parabolic interpolation, the coastal line and some small islands show more clearly than other cases. The maximum height of inland is around 140 meters higher, while the minimum of sea height is about 80 meter lower. As it concerns the results of each scheme it seems that the sixteen-point overlapping parabolic scheme indicates the well agreement with observed surface wind data. Consequently, topographic changes due to interpolation methods can lead to the significant influence on mesoscale wind field simulation of WRF modeling.

• International Journal of Automotive Technology
• /
• 제8권3호
• /
• pp.375-382
• /
• 2007

The multi-driver off-road vehicle drive-line consists of many components, with close connections among them. In order to design and analyze the drive-line efficiently, a modular methodology should be taken. The aim of a modular approach to the modeling of complex systems is to support behavior analysis and simulation in an iterative and thus complex engineering process, by using encapsulated submodels of components and of their interfaces. Multi-driver off-road vehicles are comparatively complicated. The driving-line is an important core part to the vehicle, it has a significant contribution to the performance. Multi-driver off-road vehicles have complex driving-lines, so performance is heavily dependent on the driving-line. A typical off-road vehicle's driving-line system consists of a torque converter, transmission, transfer case and driving-axles, which transfers the power generated by the engine and distributes it effectively to the driving wheels according to the road condition. According to its main function, this paper proposes a modularized approach for design and evaluation of the vehicle's driving-line. It can be used to effectively estimate the performance of the driving-line during the concept design stage. Through an appropriate analysis and assessment method, an optimal design can be reached. This method has been applied to practical vehicle design, it can improve the design efficiency and is convenient to assess and validate the performance of a vehicle, especially of multi-driver off-road vehicles.

• Journal of Mechanical Science and Technology
• /
• 제18권7호
• /
• pp.1074-1085
• /
• 2004

There are many intermediate web guides in cold rolling mills process such as CRM (cold rolling mill), CGL (continuous galvanizing line), EGL (electrical galvanizing line) and so on. The main functions of the web guides are to adjust the center line of the web (strip) to the center line of the steel process. So they are called CPC (center position control). Rapid process speed cause large deviation between the center position of the strip and the process line. Too much deviation is not desirable. So the difference between the center position of the strip and the process line should be compensated. In general, the center position control of the web is obtained by the hydraulic driver and electrical controller. In this paper, we propose modelling and several controller designs for web-guide systems. We model the web and guide by using geometrical relations of the guide ignored the mass and stiffness of the web. To control the systems, we propose PID controllers with their gains tuned by the Ziegler-Nichols method, the H$\_$$\infty$/ controller model-matching method, and the coefficient diagram method (CDM). CDM is modified for high order systems. The results are verified by computer simulations.

• 조명전기설비학회논문지
• /
• 제29권5호
• /
• pp.65-70
• /
• 2015

Lightning is one of hazards affecting the rapid-transit railway system. There are two effects, which are direct lightning surge to electric car line and induced lightning surge. Protection methods for the direct lightning surge are studied with various occasions, however, study of induced lightning surge is insufficient in spite of a large or small effects. In this paper, it is analysed the way that serge voltage is induced to electric car line by lightning strikes. By modeling the propagation process and the coupling phenomenon of electromagnetic wave produced by lightning strikes, it is achieved to make integrative circuit model combined with existing electric car model. The study is conducted into three different waveform of electromagnetic wave produced by lightning; rectangular wave, double exponential distribution wave, triangle wave. It is also simulated that the inducing serge is coupled to electric car line in an arbitrary location. The simulation results in that, when rapidly changing rectangular wave is supplied, maximum power is induced to electric car line.

• 한국컴퓨터정보학회논문지
• /
• 제15권12호
• /
• pp.1-9
• /
• 2010

본 논문에서는 첨단 통신 기술을 포함한 IT 기술을 전통산업과 융합한 병렬 이벤트 기반 원격 IT 융합 사례들을 개발하였다. IT 융합 사례들은 다수의 장치와 사용자가 동시에 시스템에서 제공되는 서비스를 이용하거나 이벤트를 발생시킨다. 따라서 다양한 장치들로부터 동시에 발생되는 이벤트를 처리하기 위해 병렬 처리 기법이 필요하다. 이에 본 논문에서는 스레드를 생성하여 병렬 처리가 가능하도록 개발하였으며, 또한 장치와 원격 정보 송수신을 위해 무선 통신 및 전력선 통신과의 연결을 할 수 있는 기술을 개발하였다. 그리고 장치 및 장치와 사용자 포털에서 발생하는 이벤트들을 논리적으로 모델링하기 위해 XML을 이용하여 객체 지향 모델링 기법으로 모델링하였다. 특히 결과들을 효과적으로 보여주기 위해 다양한 시각적인 사용자 인터페이스, 즉 그래프, 테이블 및 그래프와 테이블을 혼합한 방식을 이용하여 실시간으로 볼 수 있도록 개발하였다.

• 한국컴퓨터정보학회논문지
• /
• 제23권11호
• /
• pp.51-57
• /
• 2018

In this paper, we studied about the extraction of the parameter and implementation of speechreading system to recognize the Korean 8 vowel. Face features are detected by amplifying, reducing the image value and making a comparison between the image value which is represented for various value in various color space. The eyes position, the nose position, the inner boundary of lip, the outer boundary of upper lip and the outer line of the tooth is found to the feature and using the analysis the area of inner lip, the hight and width of inner lip, the outer line length of the tooth rate about a inner mouth area and the distance between the nose and outer boundary of upper lip are used for the parameter. 2400 data are gathered and analyzed. Based on this analysis, the neural net is constructed and the recognition experiments are performed. In the experiment, 5 normal persons were sampled. The observational error between samples was corrected using normalization method. The experiment show very encouraging result about the usefulness of the parameter.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.357-362
• /
• 2002

Most of battery industries are growing explosively as a core strategy industry for the development of the semi-conductor, the LCD, and the mobile communication device. In this thesis, dynamic characteristics of the steel can labeling machine on the automatic cell assembly line are studied. Dynamic characteristic analysis consists of dynamic behavior analysis and finite element analysis and is necessary for effective design of machines. In the dynamic behavior analysis, the displacement, velocity, applied force and angular velocity of each components are simulated according to each part. In the FEA, stress analysis, mode analysis, and frequency analysis are performed for each part. The results of these simulations are used for the design specification investigation and compensation for optimal design of cell manufacturing line. Therefore, Virtual Engineering of the steel can labeling machine on the automatic cell assembly line systems are modeled and simulated. 3D motion behavior is visualized under real-operating condition on the computer window. Virtual Prototype make it possible to save time by identifying design problems early in development, cut cost by reducing making hardware prototype, and improve quality by quickly optimizing full-system performance. As the first step of CAE which integrates design, dynamic modeling using ADAMS and FEM analysis using NASTRAN are developed.