• Journal of Electrical Engineering and Technology
• /
• 제8권4호
• /
• pp.694-703
• /
• 2013

In electric power system, the line stability indices adopted in most of the instances laid stress on variation of reactive power than real power variation of the transmission line. In this paper, a proposal is made with the formulation of a New Voltage Stability Index (NVSI) which originates from the equation of a two bus network, neglecting the resistance of transmission line, resulting in appreciable variations in both real and reactive loading. The efficacy of the index and fuzzy based load flow are validated with IEEE 30 bus and Tamil Nadu Electricity Board (TNEB) 69 bus system, a practical system in India. The results could prove that the identification of weak bus and critical line in both systems is effectively done. The weak area of the practical system and the contingency ranking with overloading either line or generator outages are found by conducting contingency analysis using NVSI.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 II
• /
• pp.745-749
• /
• 2001

The rigid body properties of a structure may be estimated easily if the mass-line of the structure could be taken exactly. However, the exact mass-line cannot be obtained experimentally. In the past years, the modal analysis for which the structure is mounted on the flexible supporter is frequently used to acquire the mass-line. Unfortunately, it is difficult not only to mount the structure but also to decouple the coupled 6 dof mode. If the structure is pended by very long and flexible rope to act free, the rigid-body modes influenced by the rope will be eliminated and the improved mass-line will be obtained. In this paper, the method using the mass-line of F.R.F. for rigid body in free-condition is suggested. The robustness of the suggested method was tested and verified numerically. The experimental results also showed a good agreement with the true value.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제55권7호
• /
• pp.313-318
• /
• 2006

An automatic sample centering system is underway at the protein crystallography beam line of the Pohang Light Source to improve the efficiency of the crystal screening process. A sample pin which contains a protein crystal is mounted on a goniometer head. Then the crystal should be moved to the center of X-ray beam by controlling the motorized goniometer to obtain diffraction data. Since the X-ray beam is located at the center of the image obtained from the CCD camera when the image of the sample pin is in focus, an auto-focusing algorithm is a very important part in the auto-sample-centering system. However the results of applying several well-known auto focusing algorithms directly to the images are not satisfactory owing to the following factors: misalignment of CCD camera, non-uniform cryo-stream in the background of the image and the supporter of the loop. The performance of an auto-focusing algorithm can be increased if the algorithm is applied to only the loop region identified. Non-uniform cryo-stream and a various illumination condition and a stain, which is shown in the image, are main obstacles to loop region identification. In this paper, a simple loop region identification algorithm, which can solve these problems, is proposed and the effective ness of the proposed scheme is shown by applying the auto-focusing algorithm to the loop region identified.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1999년도 제14차 학술회의논문집
• /
• pp.153-156
• /
• 1999

The technique is reported of identifying parameters in off-line process. The technique demands that closed-loop system consists of a reference and two-degree-of-freedom controllers (TDFC) in real process. A model process is the same as the real process except their parameters. Deviations are differences between the reference and the output of the plant or the model. The technique is based on minimizing identification error between the two deviations. The parameter differences between the plant and the model are characterized of mean value and of variance which are derived from the identification error. Consequently, the algorithm which identifies the unknown plant parameters is shown by minimizing the mean value and the variance, respectively, within double convergence loops. The technique is applied to course change of a ship. The plant deviation at the first trial is shown to occur in replacing the nominal parameters by the default parameters. The plant deviation at the second trial is shown to not occur in replacing the nominal parameters by the identified parameters. Hence, the identification technique is confirmed to be feasible in the real field.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제1권2호
• /
• pp.3-9
• /
• 2012

The paper describes a novel technique for on line parameter identification of three-phase induction motors from a single, run up to speed test. Data is sampled during this test with the normal locked rotor and synchronous speed data captured on the way to reaching the motor's rated speed. Rotor parameter variations with frequency due to skin and proximity effects and other non-linear imperfections such as heating and main flux path saturation are taken into account. This method is ideal for determining and/or verifying parameters used in high performance drives.

• Smart Structures and Systems
• /
• 제11권1호
• /
• pp.19-34
• /
• 2013

The objective of this paper is to develop on-line system parameter estimation and damage detection technique from the response measurements through using the Recursive Covariance-Driven Stochastic Subspace identification (RSSI-COV) approach. To reduce the effect of noise on the results of identification, discussion on the pre-processing of data using recursive singular spectrum analysis (rSSA) is presented to remove the noise contaminant measurements so as to enhance the stability of data analysis. Through the application of rSSA-SSI-COV to the vibration measurement of bridge during scouring experiment, the ability of the proposed algorithm was proved to be robust to the noise perturbations and offers a very good online tracking capability. The accuracy and robustness offered by rSSA-SSI-COV provides a key to obtain the evidence of imminent bridge settlement and a very stable modal frequency tracking which makes it possible for early warning. The peak values of the identified $1^{st}$ mode shape slope ratio has shown to be a good indicator for damage location, meanwhile, the drastic movements of the peak of $2^{nd}$ mode slope ratio could be used as another feature to indicate imminent pier settlement.

• 한국정보통신학회논문지
• /
• 제9권3호
• /
• pp.627-632
• /
• 2005

사용자 고유번호와 패스워드 기반의 사용자 인증 매커니즘을 수행하는 네트워크 시스템 환경에서는 스니퍼 프로그램 등을 이용하여 불법 도청함으로써 쉽게 사용자의 패스워드를 알아낼 수 있다. 이러한 불법적인 도청에 의한 패스워드 노출 문제를 해결하는 방법으로 일회용 패스워드, Challenge-Response 인증 방식이 유용하게 사용되며, 클라이언트/서버 환경에서는 별도 동기가 필요 없는 시간을 이용한 일회용 패스워드 방식이 특히 유용하게 사용될 수 있다. 안전성은 Square root problem에 기초를 두고 있고, 프리플레이 공격, 오프라인 사전적 공격 그리고 서버 등을 포함하여 지금까지 잘 알려진 공격들에 대해서 안전성을 높이기 위한 OPI(One Pass Identification)을 제안한다. OPI는 패스워드를 생성하는데 특별한 키를 생성할 필요가 없다는 것이다. OPI는 승인된 자를 확인된 데 걸리는 시간이 적게 소요되면서 뛰어났다.

• Journal of Power Electronics
• /
• 제16권4호
• /
• pp.1387-1395
• /
• 2016

A method for the identification of mechanical parameters based on integral calculation is presented. Both the moment of inertia and the friction constant are identified by the method developed here, which is based on well-known mechanical differential equations. The mechanical system under test is excited according to a pre-determined low-frequency sinusoidal motion, minimizing the distortion, and increasing the accuracy of the results. The parameters are identified using integral calculation, increasing the robustness of the results against measurement noise. Experimental data are supported by simulation, confirming the effectiveness of the proposed technique. The performance improvements shown here are of use in the design of speed and position controllers and observers. Owing to its simplicity, this method can be readily applied to commercial inverter products.

• 한국통신학회논문지
• /
• 제34권2B호
• /
• pp.119-129
• /
• 2009

유비쿼터스 환경이 도래함에 따라 실외 환경에서의 위치 기반 서비스뿐만 아니라 실내 위치 기반 서비스의 요구가 증가되고 있다. 이에 따라 본 논문에서는 실내 환경에서 객체의 위치를 효과적으로 측위할 수 있는 시스템을 제안한다. 본 논문에서 제안하는 시스템은 실내 환경에서 문제가 되는 비가시선 문제의 해결을 위해 비가시선 식별과 완화하는 기법을 도입했으며, 결과 데이터의 오류 데이터를 최소화하기 위해 잔여-가중치 알고리즘과 칼만 필터를 적용하여 위치 데이터를 보정하는 방법으로 위치 측위시 정확도를 향상시켰다. 마지막으로 제안된 실내 위치 측위 시스템의 성능을 검증하기 위해 기존의 대표적인 위치 척도인 삼각측량 기법과 제안한 위치 측위 시스템의 성능을 비교 및 분석한다.

• 한국산학기술학회논문지
• /
• 제13권8호
• /
• pp.3779-3784
• /
• 2012

산업체 공정의 실시간 공정 모니터링과 진단은 생산 제품의 품질과 안전을 보장하는데 반드시 필요한 활동들의 하나이다. 그중에서 공정 진단은 공정에 발생된 특정 이상상황의 원인을 밝혀내는 것으로서 조업자들이 이상상황의 근본원인을 보다 효과적으로 도출하는데 도움을 줄 수 있다. 본 논문에서는 비선형 KFDA 기법과 데이터 전처리기법을 이용한 이상원인 진단방법을 적용하고 이의 진단 성능을 기존 선형 기법에 기반한 PCA 진단방법과 비교한다. 실제 공정을 모사한 Tennessee Eastman 공정 시뮬레이터의 공정 데이터를 통한 사례연구를 수행한 결과 기존 선형 진단 방법론 대비 신뢰할 수 있는 진단 결과를 얻을 수 있었다.