• Tribology and Lubricants
• /
• 제31권3호
• /
• pp.125-140
• /
• 2015

In this paper, we present the results of the wear analysis of journal bearings on a stripped-down single-cylinder engine during start-up and coast-down by motoring. We calculate journal bearing wear by using a modified specific wear rate considering the fractional film defect coefficient and load-sharing ratio for the asperity portion of a mixed elastohydrodynamic lubrication (EHL) regime coupled with previously presented graphical data of experimental lifetime linear wear in radial journal bearings. Based on the calculated wear depth, we obtain a new oil film thickness for every crank angle. By examination of the oil film thickness, we determine whether the oil film thickness at the wear scar region is in a mixed lubrication regime by comparing dimensionless oil film thickness, h/σ, to 3.0 at every crank angle. We present the lift-off speed and the crank angles involved with the wear calculation for bearings #1 and #2. The dimensionless oil film thickness, h/σ, illustrates whether the lubrication region between the two surfaces is still within the bounds of the mixed lubrication regime after scarring of the surface by wear. In addition, we present in tables the asperity contact pressure, the real minimum film thickness at the wear scar region, the modified specific wear rate, and the wear angle, α, for bearings #1 & #2. To show the real shape of the oil film at wear scar region, we depict the actual oil film thickness in graphs. We also tabulated the ranges of bearing angles related with wear scar. We present the wear volume for bearings #1 and #2 after one turn-on and turn-off of the engine ignition switch for five kinds of equivalent surface roughness. We show that the accumulated wear volume after a single turn-on and turn-off of an ignition switch normally increases with increasing surface roughness, with a few exceptions.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.405-406
• /
• 2002

The main subject of this paper is analyzing the patterns of maximum oil film pressure and the minimum oil film thickness under various pre-conditions of geometric shape as functions of bearing groove and proceeding oil hole in the connecting rod bearing. As the major analytical tool, elastohydrodynamic lubrication analysis has been applied and two-intertwined results of maximum oil film pressure and minimum oil film thickness have been compared and analyzed using EXCITE program. From computed results, the optimal lubrication conditions as geometric shape of bearing groove and the proceeding oil hole have been investigated. This may be useful for the bearing designer as a firm reference.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2004년도 학술대회지
• /
• pp.275-282
• /
• 2004

The engine bearing transmits the powers from cylinder to crankshaft with small clearance between con-rod and crankpin. The minimum oil film thickness is a significant parameter in the operation of bearing. The contact pressure of bearing should be considered for the reason that elastic deformation of bearing be caused by contact pressure of bearing. There are important factors which are maintaining of minimum oil film thickness expecting of the length of maximum and minimum oil film thickness with changing of the loads to keep running normally. Furthermore, this study is very crucial to develop the design of engine bearing and crankshaft system.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.99-100
• /
• 2002

Radial, tilting-pad proceeding bearings are applied in high speed rotating machines operating at stable small and mean loads and the peripheral speeds of proceeding reaching 150 m/s. The operation of bearing can be determined by static characteristics including the oil film pressure, temperature and viscosity distributions, minimum oil film thickness, load capacity, power loss, oil flow. The operation of 5-lobe tilted-pad proceeding bearing has been introduced at the assumption of adiabatic oil film. The oil film pressure, temperature and viscosity distributions habe received by iterative solution of the Reynolds', energy and viscosity equations. The resulting oil film force, minimum oil film thickness, power loss. oil flow, maximum oil film pressure, maximum temperature were computed for different sets of bearing geometric parameters as: bearing length to diameter ratio, pad angular length and width as well as pad relative clearance.

• 한국자동차공학회논문집
• /
• 제8권5호
• /
• pp.105-113
• /
• 2000

In order to clarify the final process of oil consumption, the distribution and flow of oil through each ring were visualized by induced fluorescence method. Motoring and firing test were performed in a single cylinder research engine with transparent cylinder liner. The appropriate calibration techniques were used to solve the unstability of induced light intensity as well as to know the relation of the oil film thickness and output signal. Oil behavior was also observed at dynamic state by high speed CCD camera. By analyzing the oil film thickness converted from the photographed image, it was observed that the main route of oil transport through each ring is the end gap under the usual operating condition, low engine speed and low load condition. Oil film thickness is observed to be irregular and tend to move in a body horizontally at a given piston land. And it is also found that oil flows through oil ring gap so quickly that it can be observed in a single cycle, but it flows so slowly through top and 2nd compression rings that it takes quite a long time to detect the flow.

• Tribology and Lubricants
• /
• 제16권2호
• /
• pp.114-120
• /
• 2000

This paper reports on the theoretical analysis on the lubrication characteristics between the piston ring and the grooved cylinder liner. The circular shape piston ring and two types grooves are consider, and the minimum oil film thickness during the full engine cycle are obtained by using iterative technique. The comparative results of minimum oil film thickness and viscous friction force between the smooth and grooved liner are presented. And various design parameter of piston ring and liner groove are tested. The groove in the liner generally reduces the minimum value of minimum oil film thickness, but the maximum viscous friction force is increased at the minimum film position.

• Tribology and Lubricants
• /
• 제25권1호
• /
• pp.1-6
• /
• 2009

In this paper, the minimum oil film thickness and the maximum oil film pressure of engine bearings have been analyzed by using the elastohydrodynamic theory and Taguchi's design method as functions of the oil groove width, oil hole diameter, oil hole position, and oil supply pressure. The optimized design of the engine bearing f3r an automotive Diesel engine is very important for supporting a load-carrying capacity due to gas pres-sures from the engine combustion chamber and inertia forces of the piston. The optimized design data of engine bearings indicated that the optimized oil groove width and an oil diameter of a engine bearing are 8mm at the speed of 2,000 rpm for a given 4-cylinder Diesel engine. Thus, the oil groove oil groove and an oil hole for high performances of an engine bearing may be considered as major design parameters compared to other design factors, which are strongly related to the minimum oil film thickness and the maximum oil pressure distribution of the engine oil.

• 한국자동차공학회논문집
• /
• 제12권4호
• /
• pp.36-41
• /
• 2004

The purpose of this paper is analyzing the oil film pressure distribution and the minimum oil film thickness for a connecting rod bearing using an A VL's EXCITE program. It is very important to understand optimized oil supplying holes and oil groove dimensions for supporting sufficiently inertia forces and gas pressures from the combustion chamber for a Diesel engine. The computed results indicate that the optimized oil groove width of a bearing and oil hole of a journal are recommended for high performance of a connecting rod bearing at the elastohydrodynamic lubrication zone. These results as design parameters are very useful data for a bearing designer as a firm reference of an automotive engine.

• 한국자동차공학회논문집
• /
• 제12권4호
• /
• pp.34-34
• /
• 2004

The purpose of this paper is analyzing the oil film pressure distribution and the minimum oil film thickness for a connecting rod bearing using an A VL′s EXCITE program. It is very important to understand optimized oil supplying holes and oil groove dimensions for supporting sufficiently inertia forces and gas pressures from the combustion chamber for a Diesel engine. The computed results indicate that the optimized oil groove width of a bearing and oil hole of a journal are recommended for high performance of a connecting rod bearing at the elastohydrodynamic lubrication zone. These results as design parameters are very useful data for a bearing designer as a firm reference of an automotive engine.

• 한국산학기술학회논문지
• /
• 제11권9호
• /
• pp.3119-3124
• /
• 2010

본 논문은 엔진 베어링에서 크랭크샤프트의 경사도를 고려했을 때와 고려하지 않았을 때 유막 동적거동을 컴퓨터 시뮬레이션을 이용하여 해석하였다. 본 해석은 탄성유체윤활 이론을 바탕으로 하여 최소유막의 동적특성을 수치적으로 해석하였다. 유막설계에 매우 중요한 인자인 크랭크샤프트 경사도를 고려하기 위하여 크랭크샤프트와 엔진베어링을 탄성체로 모델링 하였다. 유막거동해석을 위한 경계조건으로는 엔진 베어링에서 발생하는 비선형 구속력과 굽힘 모멘트를 고려하였고 이에 따른 크랭크샤프트의 경사도 영향을 고려함으로써 좀 더 실제 현상과 유사한 모델링을 수행하였다. 해석결과 엔진 베어링의 성능에 가장 큰 영향을 미치는 최소유막두께가 크랭크샤프트의 경사도를 고려하지 않았을 때보다 고려하였을 때 16%에서 24%정도 감소하는 것을 알 수 있었다. 또한, 해석결과에서와 같이 크랭크샤프트 경사도 증가는 최소유막두께의 감소를 유발하고 이에 따른 베어링 파손을 예측할 수 있었다. 따라서 본 논문의 해석결과가 자동차 엔진 베어링 설계 시 매우 유용한 자료로 사용될 것으로 사료된다.