• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.4
• /
• pp.27-35
• /
• 2008

This work proposes a 14b 150MS/s 0.13um CMOS ADC for SDR systems requiring simultaneously high resolution, low power, and small size at high speed. The proposed ADC employs a calibration-free four-step pipeline architecture optimizing the scaling factor for the input trans-conductance of amplifiers and the sampling capacitance in each stage to minimize thermal noise effects and power consumption at the target resolution and sampling rate. A signal- insensitive 3-D fully symmetric layout achieves a 14b level resolution by reducing a capacitor mismatch of three MDACs. The proposed supply- and temperature- insensitive current and voltage references with on-chip RC filters minimizing the effect of switching noise are implemented with off-chip C filters. The prototype ADC in a 0.13um 1P8M CMOS technology demonstrates a measured DNL and INL within 0.81LSB and 2.83LSB, at 14b, respectively. The ADC shows a maximum SNDR of 64dB and 61dB and a maximum SFDR of 71dB and 70dB at 120MS/s and 150MS/s, respectively. The ADC with an active die area of $2.0mm^2$ consumes 140mW at 150MS/s and 1.2V.

• Progress in Medical Physics
• /
• v.27 no.1
• /
• pp.37-45
• /
• 2016

In proton therapy, in vivo proton beam range verification is very important to deliver conformal dose to the target volume and minimize unnecessary dose to normal tissue. For this purpose, a multi-slit prompt-gamma camera module made of 24 scintillation detectors and 24-channel signal processing system is under development. In the present study, we have developed and tested a dual-mode signal processing system, which can operate in the energy calibration mode and the fast data acquisition mode, to process the signals from the 24 scintillation detectors. As a result of performance test, using the energy calibration mode, we were able to perform energy calibration for the 24 scintillation detectors at the same time and determine the discrimination levels for the detector channels. Further, using the fast data acquisition mode, we were able to measure a prompt-gamma distribution induced by a 45 MeV proton beam. The measured prompt gamma distribution was found similar to the proton dose distribution at the distal fall-off region, and the estimated beam range was $17.13{\pm}0.76mm$, which is close to the proton beam range of 16.15 mm measured by an EBT film.

• The Korean Journal of Pesticide Science
• /
• v.12 no.4
• /
• pp.421-428
• /
• 2008

This study was carried out to elucidate the effects of adjuvants on physicochemical properties and pest control efficacy of pesticide spray solution. Spray droplet sizes of pesticide solution decreased by addition of adjuvants even though its effect varied according to the pesticides. The adhesive effect of pesticides sprayed on target crops by addition of adjuvants varied according to the properties, the application methods, and the spray volume of pesticides. Wash-off of the deposited amount of active ingredients of the solution of tricyclazole WP and fenobucarb EC by simulated rainfall after spraying on rice plants dramatically reduced by adding adjuvants. The retained amount of active ingredients of the pesticides were $1.5{\sim}4.1$ times higher than those without adjuvants when subjected to simulated rainfall 6 hours after spraying. Addition of adjuvants to the propanil EC spray solution enhanced the control efficacy in barnyard grass, Echinocloa crus-galli Beauv. by $8{\sim}30%$, which showed a potential to reduce pesticide use.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.898-903
• /
• 2011

Units assembled in the liquid-propellant propulsion system of launch vehicles should guarantee their on- and off-design performances under the various environments as well as at the various operation modes for the launch preparation and flight of launch vehicles. Units of liquid-propellant propulsion system can be installed in launch vehicle to insert satellite(s) into target orbit(s) only under the condition that all units must pass a series of tests to confirm whether those units perform normally as designed under the environment, which may be occurred in such stages of all development and operations as development, qualification, acceptance, assembly, pre-launch preparation, launch, and flight, and whether those units have been developed according to design requirements. Requirements for such tests have been already prepared in the advanced countries in launch vehicle systems based on experiences for decades. In Korea, where is now pursuing the development of KSLV-II, the research and development of launch vehicles using liquid-propellant propulsion system have been undergone during over 10 years. Hence test requirements for the development of units consisting of liquid-propellant propulsion system should be defined and Koreanized according to the domestic environment and circumstances and based on the experiences accumulated. In this paper requirements for the tests of units in liquid-propellant propulsion system, which can be feasible domestically, have been reviewed and defined.

• The Bulletin of The Korean Astronomical Society
• /
• v.39 no.2
• /
• pp.102-102
• /
• 2014

The NISS (Near-infrared Imaging Spectrometer for Star formation history) onboard NEXTSat-1 is the near-infrared instrument onboard NEXTSat-1 which is being developed by KASI. The main scientific targets are nearby galaxies, galaxy clusters, star-forming regions and low background regions in order to study the cosmic star formation history in local and distant universe. After the Preliminary Design Review, we have fixed major specifications of the NISS. The off-axis optical design with 15cm apertureis optimized to obtain a wide field of view ($2deg.{\times}2deg.$), while minimizing the sensitivity loss. The opto-mechanical structure of the NISS was designed to be safe enough to endure in the launching condition as well as the space environment. The tolerance analysis was performed to cover the wide wavelength range from 0.95 to $3.8{\mu}m$ and to reduce the degradation of optical performance due to thermal variation at the target temperature, 200K. The $1k{\times}1k$ infrared sensor is operated in the dewar at 80K stage. We confirmed that the NISS can be cooled down to below 200K in the nominal orbit through a radiative cooling. Here, we report the preliminary design of the NISS.

• Journal of the Korea Institute of Building Construction
• /
• v.12 no.4
• /
• pp.442-450
• /
• 2012

In this study, fire resistance and residual strength were examined after the addition of PF fiber and bonding fireproofing gypsum board to a high strength concrete-model column of 50 MPa grade. At the beginning of the experiment, all the properties of base concrete appeared to satisfy the target range. In terms of the internal temperature record, a trend of slightly high temperature was shown when the fireproofing gypsum board was not bonding, and when the fireproofing gypsum board was bonding, as PF content increased gradually, the temperature was gradually lowered. In terms of the relationship, as time elapsed a low temperature was shown when fiber was mixed, and when the board was bonding, the trend of lower temperature could be confirmed. Meanwhile, in terms of spalling property, a severe explosive fracture was generated at PF 0%, and falling off was prevented as the fiber content was increased; however, discoloration and a multitude of cracks were discovered, and when the board was bonding, the trend in which the exterior became satisfactory when the content was increased emerged. In terms of the residual compressive strength, measuring of strength could not be performed at PF 0% without bonding of board, and the strength was increased as the fiber content was increased; however, there was a decrease in strength of about 30 ~ 40%, and in the case of PF 0% with the bonding of board, the strength could be measured; however, about an 80% decrease in strength was shown, and only about a 10 ~ 20% decline in strength was displayed, as the range of decrease was reduced as the fiber content was increased. Considering all of these factors, it was determined that a more efficient enhancement of fire resistance was obtained when two methods are applied in combination rather than when the PF fiber content and bonding of fireproofing gypsum board are utilized individually.

• Journal of the Korean Society of Costume
• /
• v.55 no.5 s.95
• /
• pp.108-119
• /
• 2005

The objective of the study is was investigate the condition of the battle dress uniform worn by male members of the Korean Police Special Weapons Attack Team(KP-SWAT), identify problems, and provide basic raw materials for developing improved design of BDU. For this purpose, the researcher conducted a questionnaire survey on 92 male members of SWAT (Special Weapon Attack Team) units in Seoul using a questionnaire developed through observation and interview. Also, the body sizes of male SWAT members were measured. According to the results of body size measurements, male SWAT members generally require uniforms with a target bust girth, armhole, biceps circumference, thigh and calf circumference, longer jacket length, sleeve length, and trouser length to the knee. According to the results of the questionnaire survey, they reported dissatisfaction with the fit. In addition, they said that the Pockets are positioned too low for convenient use. Many subjects reported that their trousers were too short because of the rubber rings at the bottom of the legs. In addition, many subjects requested the alteration of the inconveniences caused by the designs finished with velcro on the bottom collar of the upper uniform, the marks and ensigns of the upper uniform, the bottom of the upper and lower uniform, and several pockets. Furthermore, there were many complaints concerning how they had to wear their uniform. The most frequently worn out and the body parts most often injured in field training and operations, they were reported, on the upper uniform, as the elbow, collar, neck, armpit, shoulder, and sleeve hem in that order, and on the lower uniform, the knee, interior calf, waist (belt rings), buttocks (rear pockets), and the bottom of the trousers (ankle) in that order As for questions concerning priorities in the improvements of the operational uniform and preferred design, the subjects recommended improvement in safety (protectiveness), workability (motional flexibility), design (shape), fit (size), comfort, ease in terms of putting on and taking off, etc., and the majority preferred two-piece designs ($67.4\%$), followed by one-piece ($30.4\%$), or both ($2.2\%$).

• The Journal of the Acoustical Society of Korea
• /
• v.24 no.6
• /
• pp.317-324
• /
• 2005

Detection and localization of a quiet target in shallow water environments is a challenging problem because of the complicated acoustic Propagation and the Prevalence of loud surface ship interference. Matched Field Processing (MFP) can help address the concern by using a Propagation model to determine the steering vectors, thus Providing optimal away gain and localization accuracy. However, Performance of MFP have yet realized in practice, for several reasons. The most important limitation is that precise information on the underwater environments is generally not available. To examine the Performance of MFP in the East Sea of Korea, we have accomplished a series of matched acoustic Properties and localization experiment (MAPLE). We analyzed the array data measured from MAPLE which is accomplished using a vertical line array and a towed acoustic source off the east cost of Korea in Oct. 2003. We localized the acoustic source using MFP. It is well known that the temperature structure in the experimental site is affected by the short period fluctuation such as internal wave. In this paper, it is found that the sidelobe level on the MFP ambiguity surface is increased being affected by the short period fluctuation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.6
• /
• pp.521-530
• /
• 2016

Weather radar is observation equipment that transmits electromagnetic waves and receives backscattered signals from the targets. The weather radar systems of the Korea Meteorological Administration have a doppler mode that can extract the target's radial velocity. However, the radial velocity over the maximum unambiguous velocity(${\nu}_m$) for which is in a trade-off relationship with the maximum unambiguous range is folded. Therefore, a dual PRF mode of which transmits and receives signals using two different PRFs(high and low) must be used to extend the vm while maintaining the maximum unambiguous range. Using a dual PRF mode, vm can be extended to the amount of lowest common denominator of two observed vm from high and low PRF. For this extension, we have developed a velocity unfolding algorithm of which uses several criteria for classification considering observed velocity differences between high and low PRF and their error boundary. Then, correction factors are calculated for each class and are applied to unfold radial velocity. The developed algorithm was applied to the Yong-In Testbed(YIT) radar and the generated better performance of radial velocity extraction than those of the previous system.

• Journal of Korea Multimedia Society
• /
• v.11 no.9
• /
• pp.1296-1301
• /
• 2008

Ultrasonography constructs pictures of areas inside the body needs in diagnosis by bouncing high-enorgy sound waves(ultrasound) off internal tissues or organs. In constructing an ultrasonographic image, the weakness of bounding signals induces noises and detailed differences of brightness, so that having a difficulty in detecting and diagnosing with the naked eyes in the analysis of ultrasonogram. Especially, the difficulty is extended when diagnosing muscle areas by using ultrasonographic images in the musculoskeletal test. In this paper, we propose a novel image processing method that computationally extracts a muscle area from an ultrasonographic image to assist in diagnosis. An ultrasonographic image consists of areas corresponding to various tissues and internal organs. The proposed method, based on features of intensity distribution, morphology and size of each area, extracts areas of the fascia, the subcutaneous fat and other internal organs, and then extracts a muscle area enclosed by areas of the fascia. In the extraction of areas of the fascia, a series of image processing methods such as histogram stretching, multiple operation, binarization and area connection by labeling is applied. A muscle area is extracted by using features on relative position and morphology of areas for the fascia and muscle areas. The performance evaluation using real ultrasonographic images and specialists' analysis show that the proposed method is able to extract target areas being approximate to real muscle areas.