• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.663-666
• /
• 2005

Gas hydrates are ice-like compounds that form at the low temperature and high pressure conditions common in shallow marine sediments at water depths greater than 300-500 m when concentrations of methane and other hydrocarbon gases exceed saturation. Estimates of the total mass of methane carbon that resides in this reservoir vary widely. While there is general agreement that gas hydrate is a significant component of the global near-surface carbon budget, there is considerable controversy about whether it has the potential to be a major source of fossil fuel in the future and whether periods of global climate change in the past can be attributed to destabilization of this reservoir. Also essentially unknown is the interaction between gas hydrate and the subsurface biosphere. ODP Leg 204 was designed to address these questions by determining the distribution, amount and rate of formation of gas hydrate within an accretionary ridge and adjacent basin and the sources of gas for forming hydrate. Additional objectives included identification of geologic proxies for past gas hydrate occurrence and calibration of remote sensing techniques to quantify the in situ amount of gas hydrate that can be used to improve estimates where no boreholes exist. Leg 204 also provided an opportunity to test several new techniques for sampling, preserving and measuring gas hydrates. During ODP Leg 204, nine sites were drilled and cored on southern Hydrate Ridge, a topographic high in the accretionary complex of the Cascadia subduction zone, located approximately 80km west of Newport, Oregon. Previous studies of southern Hydrate Ridge had documented the presence of seafloor gas vents, outcrops of massive gas hydrate, and a pinnacle' of authigenic carbonate near the summit. Deep-towed sidescan data show an approximately $300\times500m$ area of relatively high acoustic backscatter that indicates the extent of seafloor venting. Elsewhere on southern Hydrate Ridge, the seafloor is covered with low reflectivity sediment, but the presence of a regional bottom-simulating seismic reflection (BSR) suggests that gas hydrate is widespread. The sites that were drilled and cored during ODP Leg 204 can be grouped into three end-member environments basedon the seismic data. Sites 1244 through 1247 characterize the flanks of southern Hydrate Ridge. Sites 1248-1250 characterize the summit in the region of active seafloor venting. Sites 1251 and 1252 characterize the slope basin east of Hydrate Ridge, which is a region of rapid sedimentation, in contrast to the erosional environment of Hydrate Ridge. Site 1252 was located on the flank of a secondary anticline and is the only site where no BSR is observed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.2
• /
• pp.263-268
• /
• 2016

A rapid increase of data amount, used in ship-to-ship transmission of safety and logistics information, ships in the inland sea have trouble transmitting real-time information transmission due to an increase in traffic load caused by data transmitted by land station and offshore ships. In this study, therefore, communication is carried out by adaptively controlling the detailed beam width based on the distribution of offshore ships in land station durable in marine environment. Then after the adaptive sector system enabling real-time communication support between ships concentrated in an inland sea and land station is applied, the performance verification is conducted based on the respective Call Blocking Rates of an omnidirectional antenna, fisted sector system, and adaptive sector system. The performance verification result shows that adaptive sector system has better performance than the fixed sector system as the density of ship, q value, increases, and that the smaller the beam width is, the better performance of adaptive sector system will be.

• Korean Journal of Ecology and Environment
• /
• v.49 no.4
• /
• pp.245-257
• /
• 2016

Although rivers cover only 0.5% of the total land area on the Earth, they are windows that show the integrated effects of watershed biogeochemistry. Studies on the loads and properties of riverine carbon have been conducted because they are directly linked with drinking water quality, and because regional or global net ecosystem production (NEP) can be overestimated, unless riverine carbon loads are subtracted. Globally, ${\sim}0.8-1.5Pg\;yr^{-1}$ and ${\sim}0.62-2.1Pg\;yr^{-1}$ of carbon are transported from terrestrial ecosystems to the ocean via rivers and from inland waters to the atmosphere, respectively. Concentrations, ${\delta}^{13}C$, and fluorescence spectra of riverine carbon have been investigated in South Korea to understand the spatiotemporal changes in the sources. Precipitation as well as land use/land cover can strongly influence the composition of riverine carbon, thus shifting the ratios among DIC, DOC, and POC, which could affect the concentrations, loads, and the degradability of adsorbed organic and inorganic toxic materials. A variety of analyses including $^{14}C$ and high resolution mass spectroscopy need to be employed to precisely define the sources and to quantify the degradability of riverine carbon. Long-term data on concentrations of major ions including alkalinity and daily discharge have been used to show direct evidence of ecosystem changes in the US. The current database managed by the Korean government could be improved further by integrating the data collected by individual researchers, and by adding the major components ions including DIC, DOC, and POC into the database.

• Korean Journal of Ecology and Environment
• /
• v.53 no.4
• /
• pp.311-323
• /
• 2020

We analyzed food sources of 45 fish species in 28 genera of 12 families based on literature data in freshwater ecosystems of South Korea. The food sources of 45 fish species included in a total of 26 phyla, 42 classes, 94 orders, 189 families and 294 genera. Among them, animal food sources were 16 phyla, 24 classes, 54 orders, 126 families and 212 genera, whereas plant food sources were relatively small with 10 phyla, 18 classes, 42 orders, 63 families and 82 genera. The animal food sources were classified into Arthropod, Insecta, Diptera and Chironomidae according to taxa. Meanwhile, Bacillariophyta, Bacillariophyceae, Cymbellales and Cymbellaceae were the most abundant among the plant sources. Self-Organized Map (SOM) and network analysis were conducted the food sources were classified into taxonomic groups and the feeding types of fish : 45 fish species were divided into five groups, characterizing 1) fishvores, 2) invertebratevores, planktivores including 3) zooplankton and 4) phytoplankton, and 5) omnivores. The network analysis presented link association between fishes and food sources. Macroinvertebrate including diptera and ephemeroptera were revealed as hub food sources based on network analysis. This literature study would expect that the application model with the food source of fish could be utilized for the evaluation of the food network or chain in freshwater ecosystems.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.4
• /
• pp.289-299
• /
• 2011

We studied the characteristics of pollutant concentrations in 9 streams that flow into Shihwa Lake in order to provide the scientific data for effective implementation of total pollution loads management system (TPLMS) of the Lake. Suspended solid (SS), chemical oxygen demand (COD), dissolved nutrients ($NO_2$, $NO_3$, $NH_4$, $PO_4$ and $SiO_2$), total phosphorus (TP) and total nitrogen (TN) in stream water from industrial complexes, urban and agricultural regions were determined. Pollutant concentrations in December were higher than that in other sampling periods. COD concentration from industrial complex region with average of 12.6 mg/L was 2 times higher those from urban region (6.6 mg/L) and agricultural region (5.9 mg/L). TP concentration from industrial region also showed higher concentration than other regions. TN concentration in stream water was 5.89 mg/L for industrial region, 3.02 mg/L for urban region and 5.27 mg/L for agricultural region, respectively, suggesting inflow of TN due to fertilizer usage in agricultural field. Relative percentage of nitrogen compounds in TN follows the sequence: $NH_4$ (35.1%) > $NO_2$ (20.0%) > DON (22.8%) > PON (8.9%) > $NO_2$ (3.2%). Concentrations of dissolved nutrients, TP and TN in stream water were 3.2~37.2 times higher than that in Shihwa Lake seawater, therefore large amount of pollutants may be directly entered into Shihwa Lake without any treatment. For Gunja stream of industrial region, pollutants at midstream showed relatively higher concentration compared to upstream and downstream. It is necessary to manage the illegal discharging of sewage and waste water. Our results provide valuable informations on the estimation and reduction of total pollutant loads in the process of establishing adequately strategic and implemental plan of Shihwa Lake TPLMS.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.5
• /
• pp.594-604
• /
• 2021

To evaluate the causes of beach erosion in Sinji-Myeongsasimni Beach, external forces, such as tides, tidal currents, and waves, were observed seasonally from March 2019 to March 2020, and the surface sediments were analyzed for this period. In addition, the shoreline positions and beach elevations were regularly surveyed with a VRS GPS and fixed-wing drone. From these field data, the speed of the tidal currents was noted to be insufficient, but the waves were observed to af ect the deformation of the beach. As the beach is open to the southern direction, waves of heights over 1 m were received in the S-SE direction during the spring, summer, and fall seasons. Large waves with heights over 2 m were observed during typhoons in summer and fall. Because of the absence of typhoons for the previous two years from July 2018, the beach area over datum level (DL) as of July 2018 was greater by 30,138m² compared with that of March 2019, and the beach area as of March 2020 decreased by 61,210m² compared with that of March 2019 because of four typhoon attacks after July 2018. The beach volume as of March 2019 decreased by 5.4% compared with that of July 2018 owing to two typhoons, and the beach volume as of September 2019 decreased by 7.3% because of two typhoons during the observation year. However, the volume recovered slightly by about 3% during fall and winter, when there were no high waves. According to the sediment transport vectors by GSTA, the sediments were weakly influxed from small streams located at the center of the beach; the movement vectors were not noticeable at the west beach site, but the westward sediment transport under the water and seaward vectors from the foreshore beach were prominently observed at the east beach site. These patterns of westward sediment vectors could be explained by the angle between the annual mean incident wave direction and beach opening direction. This angle was inclined 24° counterclockwise with the west-east direction. Therefore, the westward wave-induced currents developed strongly during the large-wave seasons. Hence, the sand content is high in the west-side beach but the east-side beach has been eroded seriously, where the pebbles are exposed and sand dune has decreased because of the lack of sand sources except for the soiled dunes. Therefore, it is proposed that efforts for creating new sediment sources, such as beach nourishment and reducing wave heights via submerged breakwaters, be undertaken for the eastside of the beach.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.4
• /
• pp.363-371
• /
• 2023

To construct a ship, blocks of various sizes must be moved and erected . In this process, lugs are used such that they match the block fastening method and various functions suitable for the characteristics of each shipyard facility. The sizes and shapes of the lugs vary depending on the weight and shape of the block structures. The structure is reinforced by welding the doubling pads to compensate for insufficient rigidity around the holes where the shackle is fastened. As for the method of designing lugs according to lifting loading conditions, a simple calculation based on the beam theory and structural analysis using numerical modeling are performed. In the case of the analytical method, a standardized evaluation method must be established because results may differ depending on the type of element and modeling method. The application of this ambiguous methodology may cause serious safety problems during the process of moving and turning-over blocks. In this study , the effects of various parameters are compared and analyzed through numerical structural analysis to determine the modeling conditions and evaluation method that can evaluate the actual structural response of the lug. The modeling technique that represents the plate part and weld bead around the lug hole provides the most realistic behavior results. The modeling results with the same conditions as those of the actual lug where only the weld bead is connected to the main body of the lug, showed a lower ulimated strength compared with the results obtained by applying the MPC load. The two-dimensional shell element is applied to reduce the modeling and analysis time, and a safety working load was verified to be predicted by reducing the thickness of the doubling pad by 85%. The results of the effects of various parameters reviewed in the study are expected to be used as good reference data for the lug design and safe working load prediction.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.30 no.1
• /
• pp.127-134
• /
• 2024

With the growth of offshore wind power generation market, the corresponding installation vessel market is also growing. It is anticipated that approximately 100 installation vessels will be required in the of shore wind power generation market by 2030. With a price range of 300 to 400 billion Korean won per vessel, this represents a high-value market compared to merchant vessels. Particularly, the demand for large installation vessels with a capacity of 11 MW or more is increasing. The rapid growth of the offshore wind power generation market in the Asia-Pacific region, centered around China, has led to several discussions on orders for operational installation vessels in this region. The seabed geology in the Asia-Pacific region is dominated by clay layers with low bearing capacity. Owing to these characteristics, during vessel operations, significant spudcan and leg penetration depths occur as the installation vessel rises and descends above the water surface. In this study, using penetration variables ranging from 3 to 21 m, the unique vibration period, structural safety of the legs, and conductivity safety index were assessed based on penetration depths. As the penetration depth increases, the natural vibration period and the moment length of the leg become shorter, increasing the margin of structural strength. It is safe against overturning moment at all angles of incidence, and the maximum value occurs at 270 degrees. The conditions reviewed through this study can be used as crucial data to determine the operation of the legs according to the penetration depth when developing operating procedures for WTIV in soft soil. In conclusion, accurately determining the safety of the leg structure according to the penetration depth is directly related to the safety of the WTIV.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.6
• /
• pp.853-865
• /
• 2022

In this study, from August to October 2019, we conducted a survey of the spatial distribution and dominant species of macrobenthos on the rocky intertidal zones of 38 specified islands distributed along the southern coast of Korea. On the basis of observation made using 50 × 50 cm quadrats, we identified a total of 80 species, among which, Mollusca were the most abundant fauna, with 54 species that accounted for 67.4% of the total, followed by Crustacea with 15 species (18.7%). The recorded numbers of Cnidaria, Porifera, and Echinodermata species ranged from 1 to 6. In terms of the regional patterns of species richness, specified islands in Yeosu were found to be the most species rich, supporting 61 species, whereas islands in Hadong, Namhae, and Chujado were found to have a similar level of species richness, ranging from 42 to 46 species. Islands in Boseong and Goheung were home to the fewest species, with only 29 species being recorded. At the sampling station scale, we noted a considerable difference in faunal richness, ranging from 6 (St. 6) to 33 (St. 20) species. Among the recorded species, Echinolittorina radiata was identified as the dominant species on 15 specified islands, with the next most abundant species being Tetraclita japonica, considered an indicator species of climate change, which was recorded on 11 islands. In terms of frequency, E. radiata, found on 36 islands, was identified as the most frequently occurring species, followed by Reishia clavigera (30 islands), Mytilisepta virgata (29), Nerita japonica (28), Ligia. exotica (27), and Littorina brevicula (26). Of the 80 species identified, 9, 4, and 2 species of Mollusca, Crustacea, and Cnidaria, respectively, are classified as Marine fauna of accepted foreign export, whereas 50 are Red List species, 44 are species of Least Concern, 3 are Data Deficient species, and 1 species was not evaluated. However, during the survey, we found no Near Threatened or Not Applicable species. On the basis of the findings of this survey, it would appear that the abundance and richness of macrobenthic fauna inhabiting the rocky intertidal zones of specified islands along the southern coast of Korea differ according to different habitat conditions, particularly with respect to the duration of exposure and the extent and properties of the substrata. The findings of this study will provide baseline data for future monitoring and management of specified islands in Korea.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.26 no.4
• /
• pp.197-206
• /
• 2014

The purpose of this study is to evaluate coastal erosion due to a sea-level rise. The shoreline retreat rate was calculated due to future sea-level rise. Shoreline retreat rates were quantified with the cross-sectional data of 23 sandy coasts (12 sites from east coast, 5 sites from south coast, and 6 sites of west coast) and 3 cross-sectional profiles from each side of the coasts in Korea. The theory of equilibrium beach profile was employed in this study to evaluate the applicability of the theory into the coast of Korea and was tested with 15 cross-sectional beach profiles. Four scenarios of future sea level rise such as 38 cm, 59 cm, 75 cm, and 100 cm were adopted to estimate the shoreline retreat rates. Overall shoreline retreat rates for the coasts in Korea were predicted as 43.7% for 38 cm, 60.3% for 59 cm, 69.2% for 75 cm, and 80.1% for 100 cm sea level rises, respectively. Retreat rates in the east coast (29.6% for 38 cm, 45.1% for 59 cm, 56.0% for 75 cm, and 69.9% for 100 cm) showed relatively low compared to the south coast (51.9%, 67.6%, 77.2%, 87.3%) and the west coast (53.8%, 71.0%, 78.5%, 86.4%). However, all sandy coasts in Korea were assessed to be vulnerable with increasing sea-level rise. There are uncertainties in the assessment of this study, which include the limitation of the assessment model and the lack of the spatio-temporal data of the beach profiles. Therefore, this study shows that it is very important to spend integrated efforts to respond coastal erosion including comprehensive observations(monitoring) and the development of scientific understanding on the field.