• 한국산학기술학회논문지
• /
• 제16권10호
• /
• pp.6611-6617
• /
• 2015

본 연구는 수작업으로 제작된 metal coping과 CAD/CAM(Computer Aided Design/Computer Aided Manufacturing)으로 제작된 지르코니아 coping을 제작하여 변연과 내면 적합도를 비교 분석하고자 하였다. 모형은 우레탄 모형재를 사용하여 knife, chamfer변연 두 종류의 지대치를 제작하였다. 수작업과 CAD/CAM으로 제작된 보철물의 변연 적합도를 실리콘 리플리카 테크닉방법을 사용하여 측정하였다. 적합도 측정은 현미경의 CCD카메라로 캡쳐하였다. 이때 지대치와 보철물의 거리는 이미지분석 소프트웨어에서 거리 조정이 된 상태에서 실시하였다. 측정부위는 marginal opening을 MO, marginal gap을 MG, internal gap을 IG, Axial gap을 AG, occlusal gap을 OG로 하였다. 제작법과 변연 형태에 따른 비교분석을 위해 이원배치분산분석을 실시하였으며 서로 다른 평균값들의 비교 분석을 위해서 일원배치분산분석과 Scheffe's 사후 검정을 실시하였다. 그 결과 CAD/CAM의 OG와 knife 변연의 MO을 제외하고는 < $120{\mu}m$ 적합도를 나타냈다. CAD/CAM으로 제작된 coping은 chamfer 변연 MO에서 높은 적합도를 보였으나 MG에서는 knife변연이 chamfer변연 보다 더 좋은 적합도를 보였다. AG의 내면 적합도는 가장 좋은 값을 나타내었다(< $38{\mu}m$).

• The Journal of Advanced Prosthodontics
• /
• 제12권5호
• /
• pp.283-290
• /
• 2020

PURPOSE. The present study aimed to evaluate the clinical applicability of monolithic zirconia (MZ) crowns of different thickness via determination of fracture resistance and marginal fit. MATERIALS AND METHODS. MZ crowns with 0.5, 0.8, 1.0, and 1.5 mm thickness and porcelain fused to metal (PFM) crowns were prepared, ten crowns in each group. Marginal gaps of the crowns were measured. All crowns were aged with thermal cycling (5 - 55℃/10000 cycle) and chewing simulator (50 N/1 Hz/lateral movement: 2 mm, mouth opening: 2 mm/240000 cycles). After aging, fracture resistance of crowns was determined. Statistical analysis was performed with one-way ANOVA and Tukey's HDS post hoc test. RESULTS. Fracture loads were higher in the PFM and 1 mm MZ crowns compared to 0.5 mm and 0.8 mm crowns. 1.5 mm MZ crowns were not broken even with the highest force applied (10 kN). All marginal gap values were below 86 ㎛ even in the PFM crowns, and PFM crowns had a higher marginal gap than the MZ crowns. CONCLUSION. The monolithic zirconia exhibited high fracture resistance and good marginal fit even with the 0.5 mm thickness, which might be used with reduced occlusal thickness and be beneficial in challengingly narrow interocclusal space.

• 구강회복응용과학지
• /
• 제39권3호
• /
• pp.146-157
• /
• 2023

구치부 교모나 소실로 인해 발생하는 교합붕괴에서는 수복공간이 불충분하고 심미적 문제가 발생하는 경우가 많다. 이를 해결하기 위해 고경을 증가시키면, 하악이 후하방으로 회전함으로써 상하악 전치부 사이에 공간이 발생하여 전방유도각이 상실되는 문제점이 생긴다. 이런 이유 때문에 통상 고경 증가 후에 생긴 상하악 전치부 사이 공간은 교정을 통해 전치 치축 변화를 유도하거나 보철적 수복으로 피개하여 적절한 전방유도를 얻는 것이 일반적이었다. 그러나 구치부 교모나 소실 후 발생한 전치 과개교합 형식은 하악이 전상방 회전하며 전치부에 교합력이 과도하게 집중되고 있는 상태이기 때문에, 교합력이 제거되면 전치는 원래의 치축으로 돌아갈 수 있을 것이라고 추정할 수 있다. 이런 사실에 착안하여 이 증례보고에서는 덜 침습적인 치료 방법을 고안, 교합 수직 고경 증가를 통한 전치부의 자연스러운 전방유도 재획득을 의도하였다. 이후 디지털 중첩 방법으로 전치부의 치축 개선을 확인할 수 있었다. 새로운 치료법의 적절한 적응증을 정의하며 임상에 적용할 수 있도록 증례보고 하는 바이다.

• 대한치과교정학회지
• /
• 제51권2호
• /
• pp.135-141
• /
• 2021

Objective: To assess the effects of thermoforming on aligner thickness and gap width in six aligner systems with the same nominal thickness. Methods: Six passive upper aligners of different brands were adapted to a single printed cast. Each sample was evaluated with high-resolution micro-computed tomography. To investigate aligner thickness and gap width, two-dimensional (2D) analysis was conducted assessing the effects of the following variables: tooth type (central incisor, canine, and first molar), 2D reference points, and aligner type. Data were analyzed and compared using analysis of variance and Tukey's post-hoc tests (p < 0.05). Results: Tooth type, dental region, and aligner type affected both the gap width and aligner thickness. The aligner thickness remained moderately stable across the arch only in the F22. Conclusions: All thermoformed samples displayed smaller aligner thickness and gap width at anterior teeth and both gingival and coronal centers than at posterior teeth and occlusal surfaces.

• 대한소아치과학회지
• /
• 제24권3호
• /
• pp.590-596
• /
• 1997

Ankylosis is defined as a fusion of alveolar bone with dentin and/or cementum and may occur at any time during or following active eruption. Ankylosed teeth maintain existing occlusal levels while adjacent teeth continue to erupt via deposition of alveolar bone. This may result in the clinical appearance of depression or submergence of ankylosed teeth below the occlusal plane. It is found more frequently in children of late mixed dentition and in mandibular primary molars. The problems arising from ankylosed teeth, due to their submerged positions, are elongation of the antagonist, tipping of the adjacent teeth, loss of arch length, food impaction and subsequent destruction of periodontal tissue, disturbance of succedaneous tooth eruption. The author observed several cases of ankylosed primary molars and properly managed. Following results were obtained. 1. Severe infraoccluded ankylosis results in loss of arch length and undesirable effect on eruption path of succedaneous tooth, therefore early diagnosis and management are important. 2. The teeth without problems may be examined periodically and restored in order to maintain the normal occlusal function.

• The Journal of Advanced Prosthodontics
• /
• 제9권3호
• /
• pp.159-169
• /
• 2017

PURPOSE. The purposes of this study were to evaluate the marginal and internal gaps, and the potential clinical applications of three different methods of dental prostheses fabrication, and to compare the prostheses prepared using the silicone replica technique (SRT) and those prepared using the three-dimensional superimposition analysis (3DSA). MATERIALS AND METHODS. Five Pekkton, lithium disilicate, and zirconia crowns were each manufactured and tested using both the SRT and the two-dimensional section of the 3DSA. The data were analyzed with the nonparametric version of a two-way analysis of variance using rank-transformed values and the Tukey's post-hoc test (${\alpha}=.05$). RESULTS. Significant differences were observed between the fabrication methods in the marginal gap (P < .010), deep chamfer (P < .001), axial wall (P < .001), and occlusal area (P < .001). A significant difference in the occlusal area was found between the two measurement methods (P < .030), whereas no significant differences were found in the marginal gap (P > .350), deep chamfer (P > .719), and axial wall (P > .150). As the 3DSA method is three-dimensional, it allows for the measurement of arbitrary points. CONCLUSION. All of the three fabrication methods are valid for measuring clinical objectives because they produced prostheses within the clinically acceptable range. Furthermore, a three-dimensional superimposition analysis verification method such as the silicone replica technique is also applicable in clinical settings.

• 대한치과기공학회지
• /
• 제41권1호
• /
• pp.21-27
• /
• 2019

Purpose: To evaluate 2D and 3D of occulsal, mesial-occlusal and mesial-occlusal-distal cavity of composite resin inlay. Methods: Abutment tooth 16, 36 of FDI system was selected for the study. Inlay prostheses classified as occlusal cavity (OC group), mesial-occlusal (MOC) and mesial-occlusal-distal cavity (MODC) were prepared using composite resin. Composite resin was injected with composite resin in prepared tooth cavity and then photopolymerized with UV light. Additional thermal polymerization was performed. Marginal gap of composite resin inlays were measured by digital microscope(x160) with silicone replica technique. The data was analyzed from statistical software for Kruskal-Wallis test (${\alpha}=0.05$). 3-dimensional analysis was analyzed through superimposition method. Results: The smallest 2D marginal fit measure of the three groups was $47.0{\pm}21.6{\mu}m$ in the MOC group. The largest 2D marginal was $69.1{\pm}33.8{\mu}m$ in the MODC group. In the trueness of the three groups, the most accurate figure was $14.4{\pm}2.3{\mu}m$ for the MODC group. In Precision, the most accurate figure was $14.5{\pm}4.3{\mu}m$ for the MODC group. Conclusion : In this study, 2D marginal fit of OC, MOC, and MODC cavities fabricated with composite resin was applicable to all clinical applications. In the 3D inner surface accuracy evaluation, the MODC group showed the accuracy results.

• Restorative Dentistry and Endodontics
• /
• 제26권1호
• /
• pp.32-40
• /
• 2001

The aim of this study was to evaluate the effect of various polymerization techniques on the microleakage of compomer restorations. Fifty extracted human premolars and molar were used and randomly divided into 5 groups. After cavity preparation, compomer (F2000$^{\circledR}$) was filled according to the manufacturer's directions. All groups, except group 5, were filled using an incremental technique. Group 1 was polymerized for 40 seconds at a continuous 485mW/$\textrm{cm}^2$ with a VIP$^{\circledR}$(Bisco, USA) light cure unit. Group 2 was polymerized for 20 seconds at 345mW/$\textrm{cm}^2$ and then for 20 seconds at 645mW/$\textrm{cm}^2$ with the VIP equation omitted light cure unit. Group 3 was polymerized at 400mW/$\textrm{cm}^2$, gradually increased to 50mW/$\textrm{cm}^2$ 10 seconds until 550mW/$\textrm{cm}^2$ was reached; total 40 seconds with a Spectrum 800$^{\circledR}$ (Dentsply Caulk, USA) light cure unit. Group 4 was polymerized for 3 seconds using an incremental technique with a Flipo$^{\circledR}$ (LOKKi, France) light cure unit. Group 5 was polymerized for 3 seconds using a bulk fill technique with the Flipo$^{\circledR}$ light cure unit. The specimens were embedded with acrylic resin, and were sectioned with diamond saws in a mesiodistal direction along the longitudinal axis of the tooth so as to pass through the center of the restoration, and three surfaces (occlusal, pulpal, and gingival) were examined with SEM. The results were as follows ; 1. Group 5 showed a significantly larger gaps compared to other groups on the gingival, occlusal, and pulpal walls. 2. All groups except group 5 had no statistically significant gap on the gingival, occlusal, and pulpal walls. 3. There was no significant correlation between the amount of enamel on the gingival and occlusal walls and polymerization shrinkage.

• Journal of Yeungnam Medical Science
• /
• 제41권2호
• /
• pp.80-85
• /
• 2024

Background: This study aimed to compare and evaluate the marginal fit of nanocomposite computer-aided design/computer-aided manufacturing (CAD/CAM) inlays. Three types of nanocomposite CAD/CAM blocks (HASEM, VITA Enamic, and Lava Ultimate) were used as materials. Methods: Class II disto-occlusal inlay restorations were prepared on a typodont mandibular right first molar using diamond rotary instruments. The inlays were fabricated using CAD/CAM technology and evaluated using the silicone replica technique to measure marginal gaps at five locations on each inlay. The data were analyzed by two-way analysis of variance and Tukey post hoc tests (α=0.05). Results: There were no significant differences in the marginal gaps based on the type of nanocomposite CAD/CAM inlay used (p=0.209). However, there was a significant difference in the marginal gaps between the measurement regions. The gingival region consistently exhibited a larger marginal gap than the axial and occlusal regions (p<0.001). Conclusion: Within the limitations of this in vitro study, the measurement location significantly influenced the marginal fit of class II disto-occlusal inlay restorations. However, there were no significant differences in the marginal gaps among the different types of CAD/CAM blocks. Furthermore, the overall mean marginal fits of the class II disto-occlusal inlay restorations made with the three types of nanocomposite CAD/CAM blocks were within the clinically acceptable range.

• The Journal of Advanced Prosthodontics
• /
• 제15권3호
• /
• pp.155-170
• /
• 2023

PURPOSE. This study aims to clinically compare the fitness and trueness of zirconia crowns fabricated by different combinations of open CAD-CAM systems. MATERIALS AND METHODS. Total of 40 patients were enrolled in this study, and 9 different zirconia crowns were prepared per patient. Each crown was made through the cross-application of 3 different design software (EZIS VR, 3Shape Dental System, Exocad) with 3 different processing devices (Aegis HM, Trione Z, Motion 2). The marginal gap, absolute marginal discrepancy, internal gap(axial, line angle, occlusal) by a silicone replica technique were measured to compare the fit of the crown. The scanned inner and outer surfaces of the crowns were compared to CAD data using 3D metrology software to evaluate trueness. RESULTS. There were significant differences in the marginal gap, absolute marginal discrepancy, axial and line angle internal gap among the groups (P < .05) in the comparison of fit. There was no statistically significant difference among the groups in terms of occlusal internal gap. The trueness ranged from 36.19 to 43.78 ㎛ but there was no statistically significant difference within the groups (P > .05). CONCLUSION. All 9 groups showed clinically acceptable level of marginal gaps ranging from 74.26 to 112.20 ㎛ in terms of fit comparison. In the comparison of trueness, no significant difference within each group was spotted. Within the limitation of this study, open CAD-CAM systems used in this study can be assembled properly to fabricate zirconia crown.