• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.10
• /
• pp.1335-1342
• /
• 2000

Three-dimensional flow analysis and numerical optimization methods are presented for the design of an axial-flow fan. Steady, incompressible, three-dimensional Reynolds-averaged Navier-Stokes equations are used as governing equations, and standard k- ${\varepsilon}$ turbulence model is chosen as a turbulence model. Governing equations are discretized using finite volume method. Steepest descent method, conjugate gradient method and BFGS method are compared to determine the searching directions. Golden section method and quadratic fit-sectioning method are tested for one dimensional search. Objective function is defined as a ratio of generation rate of the turbulent kinetic energy to pressure head. Two variables concerning sweep angle distribution are selected as the design variables. Performance of the final fan designed by the optimization was tested experimentally.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.10
• /
• pp.1119-1127
• /
• 2012

In this paper, we present an inverse kinematics of a 7-dof Anthropomorphic robot arm using conformal geometric algebra. The inverse kinematics of a 7-dof Anthropomorphic robot arm using CGA can be computed in an easy way. The geometrically intuitive operations of CGA make it easy to compute the joint angles of a 7-dof Anthropomorphic robot arm which need to be set in order for the robot to reach its goal or the positions of a redundant robot arm's end-effector. In order to choose the best solution of the elbow position at an inverse kinematics, optimization techniques have been proposed to minimize an objective function while satisfying the euler-lagrange equation.

• Journal of KSNVE
• /
• v.9 no.4
• /
• pp.795-805
• /
• 1999

Rubber mounts so called grommets and pipes are two major paths of vibration transmission from a compressor, an important vibration source in an air conditioner, to the whole unit. A procedure of configuring the suction and discharge pipes of the compressor was developed in this paper so as to reduce the vibration transmission through the pipes as well as the grommets. Through investigating the effects of shapes and connecting disrections of pipe elements on vibration transmission, a guideline to configure the pipe layout, which enables to reduce vibration transmission, was proposed. The initial pipe layout by the guideline was optimized with the objective function, minimization of boty vibration transmission and the cost, and with the constraints to yield the final dimensions of the pipes. The procedure not only minimizes the transmitted force to the circumferential devices but enables to eliminate rubber blocks or dampers, which are generally used to avoid resonances of the pipe system.

• Korean Journal of Organic Agriculture
• /
• v.18 no.3
• /
• pp.291-313
• /
• 2010

The objective of this paper is to apply choice experiment methods to estimate non-market value of organic farming and its policy implication. A preliminary survey shows that the attributes of organic farming are reduce environmental pollution, bio-diversity improvements, cultural diversity improvements and maintain local community, reduce green-house gas emissions, energy saving, landscape improvements and tax for organic farming improvement policy. Questionnaire was eight different choice sets presented to each respondent. Implicit values of the attributive levels of organic farming have been calculated into tax money costs per house. This paper compared the six feasible scenarios in terms of willingness to pay per year. This study is expected to contribute to government's organic farming policies and quantitative information related to practice of organic farming.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.4 s.121
• /
• pp.324-332
• /
• 2007

Sensor placement method for damage identification has been developed for model updating using Taguchi method. In order to select the optimal sensor location, the analysis of variance of objective function using orthogonal array was carried out. Then, modal data at the selected locations were used for damage identification using model updating. The numerical model of a cantilever beam was used in order to compare the damage identification results with conventional sensor location method.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.1085-1089
• /
• 2007

An acoustic topology optimization method is developed to optimize the acoustic attenuation capability of a muffler. The transmission loss of the muffler is calculated by using the three-point method based on finite element analysis. Each element of the finite element model is assumed to have the variable acoustic properties, which are penalized by a carefully-selected interpolation function to yield clear expansion chamber shapes at the end of topology optimization. The objective of the acoustic topology optimization problem formulated in this work is to maximize the transmission loss at a target frequency. The transmission loss value at a deep frequency of a nominal muffler configuration can be dramatically increased by the proposed optimization method. Optimal muffler configurations are also obtained for other frequencies.

• KSTLE International Journal
• /
• v.2 no.1
• /
• pp.35-39
• /
• 2001

In this paper, statistical approach is undertaken to investigate the classification of wear debris which is the key function of objective assessment of wear debris morphology. Wear tests are run to produce various kinds of wear debris. The images of wear debris from wear tests are captured with image acquisition equipment. By thresholding, two-dimensional binary images of wear debris are made and, then, morphological parameters are used to quantify the images of debris. Parametric and nonparametric discriminant method are employed to classify wear debris into predefined wear conditions. It is demonstrated that classification accuracy of parametric and nonparametric discriminant method is similar. The selected use of morphological parameters by stepwise discriminant analysis can generally improve the classification accuracy of parametric and nonparametric discriminant method.

• Toxicological Research
• /
• v.17
• /
• pp.205-210
• /
• 2001

One of the major focuses and perhaps the greatest challenges during the past decade in the discipline of immunotoxicology has been the elucidation of the molecular mechanisms responsible for immunotoxicity by specific agents. Much is currently understood about the basic underlying intracellular processes that control leukocyte effector function. This fundamental information in cell biology can now be applied toward developing systematic approaches, through the application of cell and molecular biology techniques, to identify the intracellular targets and processes disrupted by immunotoxicants. The objective of this paper is two fold. First to discuss fundamental principles of experimental design aimed at elucidation of cellular mechanisms in immunotoxicology; and second to discuss the application of molecular biology techniques in characterizing the mechanism of TCDD-induced B cell dysfunction as a working example.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1998.04a
• /
• pp.684-688
• /
• 1998

Optimization of the collocated piezoceramic sensor/actuator placement is investigated numerically and verified experimentally for vibration control of laminated composite plates. The finite element method is used for the analysis of dynamic characteristics of the laminated composite plates with the piezoceramic sensor/actuator. The structural damping index(SDI) is defined from the modal damping. It is chosen as the objective function for optimization. Weights for each vibrational mode are taken into account in the SDI calculation. The gradient method is used for the optimization. Optimum location of the piezoceramic sensor/actuator is determined by maximizing tie SDI. Numerical simulation and experimental results show that the optimum location of the piezoceramic sensor/actuator is dependent upon the outer layer fiber orientations of the plate, and location and size of the piezoceramic sensor/actuator.

• Water Engineering Research
• /
• v.2 no.3
• /
• pp.171-178
• /
• 2001

There are three methods for analyzing flow and pressure distribution in looped water distribution networks (the loop method, the node method, the element method) taking into consideration hydraulic parameters chosen as unknown. For all these methods the non-linear system of equations can be solved by iterative procedures. The paper presents a different approach to this problem by using the method of variational formulations for hydraulic analysis of water distribution networks. This method has the advantage that it uses a specialized optimization algorithm which minimizes directly an objective multivariable function without constraints, implemented in a computer program. The paper compares developed method to the classic Hardy-Cross method. This shows the good performance of the new method.