• Textile Coloration and Finishing
• /
• v.18 no.6 s.91
• /
• pp.63-68
• /
• 2006

In synthetic/spandex blends fibers, contents of the synthetic fiber by percentage is higher than those of spandex. Thus, the dyeing process of the blends fiber is mainly focused on the synthetic fiber, but not the spandex. In this study, we used several series of vat dyes for dyeing the nylon/spandex blend fabrics and their dyeing properties(fk value) were investigated at various reduction agents, temperatures, pH which have the potential for deep shade dyeing effects. The formamidinesulfinic acid were found to be effective to increase the fk values of the blend fiber compared to sodium hydrosulfite and Rongalit C. Higher temperature($100^{\circ}C$) and lower pH(pH 4) were observed as suitable conditions for maximum fk values.

• Textile Coloration and Finishing
• /
• v.7 no.1
• /
• pp.72-79
• /
• 1995

The effect of copper sulfate/thiourea on the diffusion and the dye exhaustion of two dyes, C. I. Acid Orange 7 and C. I. Food Yellow 3 in nylon 6 fiber has been studied. The results obtained from the experimetal are as follows : 1) Copper sulfate reacted with thiourea at constant temperature and then generated the colorless trasparent coordination compound, and then combinated end group of carboxyl of nylon 6 fiber. 2) The coordination compound [$Cu_{2}$($TU_{6}$)] ($(SO_{4})_2$) is conducted at pH 5-6 in solution intensity and repulsed the sulfonic acid group of dyes, and therefore the diffusion of dyes is restraint. 3) Dye uptake and diffusion coefficient were decreased in the order of untreated > copper sulfate/thiourea-treated > tannin-treated.

• Asian-Australasian Journal of Animal Sciences
• /
• v.17 no.10
• /
• pp.1430-1433
• /
• 2004

A study was conducted to determine the effect of different alkali treatments on changes in chemical composition and on degradability of bagasse and rice straw. This study divided into 2 experiments, the first with bagasse and the second with rice straw. Each experiment comprised 9 treatments which included: untreated control; 3% NaOH; 6% NaOH; 3% urea; 6% urea; 3% NaOH/3% urea; 3% NaOH/6% urea; 6% NaOH/3% urea; 6% NaOH/6% urea. In both experiments, crude protein contents were increased from 2.0 to 12.5 units for bagasse and 3.1 to 13.7 units for rice straw by urea treatments. Ash contents of the treated bagasse and rice straw were increased over the untreated control (1.5-9.7 units for bagasse; 4.2-8.8 units for rice straw). The effects on ether extract, crude fiber, neutral detergent fiber and acid detergent fiber of the treated bagasse and rice straw were variable. Nylon bag degradability of dry matter and crude fiber were increased by treatments applying NaOH and NaOH plus urea but not urea alone. In contrast, the egradability of neutral detergent fiber and acid detergent fiber were reduced compared with the untreated control. From these degradability studies, it can be concluded that the most efficient treatments of bagasse were those treatments with 6% NaOH, followed by treatments with 6% NaOH plus 3% or 6% urea and 3% NaOH plus 3% or 6% urea, respectively. However, when comparison was made on the cost of chemical used to treat the agricultural by-products, particularly in case of rice straw, 3-6% urea would be appropriate.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1996.05a
• /
• pp.241-252
• /
• 1996

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.04a
• /
• pp.352-353
• /
• 2003

Clay 분산 유/무기 나노복합재 제조기술은 실리케이트 층상구조의 점토광물을 나노 스케일의 시트상의 기본 단위로 박리(exfoliation)하여 고분자수지에 분산시킴으로써 범용 고분자의 낮은 기계적 물성의 한계를 엔지니어링 플라스틱 수준으로까지 올리고자 하는 것으로서, 기존의 무기 충진재 및 강화재의 입자크기(〉1 $\mu\textrm{m}$)를 나노 스케일까지 분산시켜 기존 무기물 충진 복합재의 단점을 한층 보완하는 것을 목표로 하고 있어 성능 및 원가 면에서 매우 유리한 방법으로 21세기의 복합재료 생산시장의 판도에 상당한 변화를 가져오게 할 수 있는 핵심기술이라 할 수 있다. (중략)

• Proceedings of the Korean Fiber Society Conference
• /
• 1990.06b
• /
• pp.67-67
• /
• 1990

Three non-ionic and two anioinic spin probes, differing in size and substituent, were synthesized. Their mobility in dried nylon 6 film was investicated by the spin probe technique using electron spin resonance spectrometer. When the size of a spin probe was large and the interaction between the probe molecules and polymer chains existed, the mobility of spin probes decreased. From Arrhenius plots of rotational correlation time, one discontinuity point ($T_d$) was determined. The activation energies for rotation below and above $T_d$ were discussed in terms of the mode of probe rotation. Three spin probes could be viewed as azo dyes having a built-in nitroxide radical. Photolysis of them in dimethylformamide and in nylon 6 film was performed by exposure to 254 nm UV light in the presence of air. It was found that dyes having a built-in nitroxide radical showed better photostability than dyes derived from ${\bata}-naphthol$..

• Textile Coloration and Finishing
• /
• v.26 no.4
• /
• pp.331-338
• /
• 2014

In this research, split-type complex yarn of 20:80, 40:60, 50:50 nylon6/polyester composition ratio was used in order to impose unique sense on split-type complex woven. After treating both split-type complex yarn of each ratio and its produced woven in alkali solution, we got the following results by checking physical properties based on alkali proportion and treatment time. Under the condition of NaOH 20% in this experiment, it took approximately double time 20% loss of weight. The loss of weight became high when polyester proportion of N/P(nylon6/polyester) composition ratio was low, in the same fineness yarn. Even though polyester proportion was low, the loss of weight was low when the fineness was high. N/P division was well processed at about 25% loss of weight under the condition of NaOH 20%, treatment temperature $50^{\circ}C$, and treatment time 60 minutes. The research provides that the loss of weight should be processed around treatment time 24 hours in the case of NaOH concentration 15%, and treatment time 15 hours in the case of NaOH concentration 18%, respectively, in order to achieve N/P woven division ratio of about 70%-80% in industrial fields.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.6
• /
• pp.1023-1030
• /
• 2001

The tensile properties of short nylon6 fiber reinforced NR and SBR have been investigated as functions of diameter ratio(DR), interphase condition, fiber aspect ratio(AR), and fiber content. The short-fiber(DR=3 and AR=2) reinforced SBR did not show the dilution effect for all interphase conditions. And the short-fiber(DR=3 and AR=2) reinforced NR did not show the dilution effect except for the no-coating. The better interphase condition, the lower dilution effect at same DR. The tensile moduli are significantly improved due to fiber content and diameter ratio at same interphase condition. The pull-out force increased with the DR. The better interphase condition, the higher pull-out force at same DR. It is found that the DR and AR have an important effect on tensile properties.

• Elastomers and Composites
• /
• v.45 no.1
• /
• pp.2-6
• /
• 2010

The sizing treatments of PAN-based carbon fiber surfaces were carried out in order to improve the interfacial adhesion in the carbon fibers/nylon6 composite system. The parameter to characterize the wetting performance and surface free energy of the sized fibers were determined by a contact angle method. The mechanical interfacial properties of the composites were investigated using critical stress intensity factor ($K_{IC}$). The cross-section morphologies of sized CFs/nylon6composites were observed by SEM. As the experimental results, it was observed that silane-based sizing treated carbon fibers showed higher surface free energies than other sizing treatments. In particular, the KIC of the sizing-treated carbon fibers reinforced composites showed higher values than those of untreated carbon fibers-reinforced composites. This result indicated that the increase in the surface free energy of the fibers leads to the improvement of the mechanical interfacial properties of carbon fibers/nylon6 composites.

• The Korean Journal of Rheology
• /
• v.10 no.2
• /
• pp.57-64
• /
• 1998

A pultrusion resin impregnation (PRI) die, which has been developed recently in our laboratory, was used to pre-pare various composite system. The continuous fiber reinforced composites of glass fiber/polypropylene(GFPP) and glass fiber/polyamide 6 (GFPA) were first manufactured by means of the PRI die and then cut into chopped pellets of predet-ermined length. These pellets and either virgin or modified thermoplastic resin were melt-mixed by a twin screw extruder to prepare GF/PA/PP and GF/PA/PPMA system. The mechanical properties of these blends were investigated and discussed in terms of their morphological observations. These preliminary results revealed that this new impregnation die could be suc-cessfully applied to produce prepregs suitavle for the final shaping process.